Post by mohammedben on Fail communication between CODESYS and Fuxa SCADA via OPC UA ^{CODESYS Forge talk (Post)}
hi, When I try to establish communication between CODESYS and Fuxa SCADA via OPC UA, the connection fails, and I receive the following error: 2026-02-15T08:38:13.618Z [ERR] 'codesys' connect failure! Error: The connection may have been rejected by server, Err = (ClientTCP_transport6: socket has been disconnected by third party) 2026-02-15T08:38:13.619Z [ERR] 'codesys' try to connect error! Error: The connection may have been rejected by server, Err = (ClientTCP_transport6: socket has been disconnected by third party) 2026-02-15T08:38:13.622Z [ERR] 'codesys' connect error! undefined (1) Note that there are no problems when I establish communication with the UaExpert and OPC UA Client Simulator software. I also previously tried communicating with RapidSCADA and received the following error: Endpoint with the specified security options not found. And when I try to connect with "none" in the security policy, I get this error: BadSecureChannelClosed I have tried almost all the solutions available online and have not found a solution. I hope you can provide me with a solution that solves this problem. Thanks in advance
Last updated: 2026-02-16

Post by risele on Modbus connection via Qronox PCD3 M6893 ^{CODESYS Forge talk (Post)}
You are welcome. Also note, that it's valid only if you modbus-device use same real/float value representation (IEEE 754). That's true for most of systems. But some devices may have other representation, such as integer + position of the decimal point, for example 123.456 is integer = 123456 and position = 3 Also note, that, ones again, depending on endianess of each system, you may also need to swap not just words, but bytes. TYPE u_Real : UNION rVal:REAL; wVal:ARRAY[0..1] OF WORD; bVal:ARRAY[0..3] OF BYTE; dwVAL:DWORD; //same as previous, may be easier to specify the MB register END_UNION END_TYPE than swapping may be something as VAR A,B,C,D:BYTE; //Bytes of the real value uIn, uOut:u_Real; rVal:REAL; ModbusReg1,ModbusReg2:WORD; END_VAR uIn.rVal:=rVal; uOut.A:=uIn.D; uOut.B:=uIn.C; uOut.C:=uIn.B; uOut.D:=uIn.A; ModbusReg1:=uOut.wVal[0]; ModbusReg1:=uOut.wVal[2]; Or you even need to reorder bits... Ones again, sending float/real values is not defined by Modbus protocol itself, so it is hardware- and software-dependent. The Modbus Poll (and most of modbus tools) have configuration parameters that will properly swap bytes on their side. Ones again, that's very helpful: https://www.scadacore.com/tools/programming-calculators/online-hex-converter/
Last updated: 2026-02-19

Post by thn-power on Updating OPC UA Core Nodeset on PLS ^{CODESYS Forge talk (Post)}
Hi After much trail and error I think I found the root cause to my OPC UA problem. The problem is that I cannot manage to build and download a program with a a custom OPC UA Information model. We use a Weidmueller WL2000 PLS, but the problem also exsist on the Win V3 PLC. Our custom information model is based on the latest versions of the OPC UA Core Nodeset v 1.05.03 (2023-09-20) and UA/DI nodeset 1.04.0 (2022-11-03) Those nodesets are installed in the Codesys Information Model Repository (3.5.19.6) However, when trying to build I get the following error. [ERROR] Untitled1: Communication Manager [Device: PLC Logic: Application]: The information model http://opcfoundation.org/UA/ is required by http://bos.org/ with a minimal publication date from 15.12.2023 but the device has only a model from 15.09.2021 installed. Probably the information model from 15.09.2021 is missing in the information model repository. [ERROR] Untitled1: Communication Manager [Device: PLC Logic: Application]: The information model http://opcfoundation.org/UA/DI/ is required by http://bos.org/ with a minimal publication date from 03.11.2022 but the device has only a model from 09.03.2021 installed. Probably the information model from 09.03.2021 is missing in the information model repository. Build complete -- 2 errors, 1 warnings : No download possible I think the problem is that the UA Core nodeset is implemented in the PLC firmware (at least that in Siemens S7), and that only includes the "old" nodeset from 2021-09-21 etc. So the question is, how (or if?) can I transfer the new nodeset to the PLS? I have created separate Information models under Communication manager with the newer code nodesets (UA and DI). But it seems that the compiler does not recognize them being excising, neither in the Codesys IDE or on the PLC. Would have guessed that this is a common issue, sine many manufacturers use the latest versions of the OPC UA standard, and that it would be a solution to the problem.
Last updated: 2024-09-20

Post by paulpotat on cm4 runtime problem ^{CODESYS Forge talk (Post)}
Hello, We are having the same kind of problem again with the last CM4 we received : ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-18, 0x00000BB8, 0xFFFFFFFB) Hardware Version $ cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 3 (v7l) BogoMIPS : 126.00 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32 CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xd08 CPU revision : 3 processor : 1 model name : ARMv7 Processor rev 3 (v7l) BogoMIPS : 126.00 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32 CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xd08 CPU revision : 3 processor : 2 model name : ARMv7 Processor rev 3 (v7l) BogoMIPS : 126.00 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32 CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xd08 CPU revision : 3 processor : 3 model name : ARMv7 Processor rev 3 (v7l) BogoMIPS : 126.00 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32 CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xd08 CPU revision : 3 Hardware : BCM2711 Revision : a03141 Serial : 1000000097594db7 Model : Raspberry Pi Compute Module 4 Rev 1.1 Kernel Version $ uname -a Linux cmr-pv2-1t00-0001 6.12.25-rt9-v7l #1 SMP PREEMPT_RT Thu Sep 25 11:53:00 CEST 2025 armv7l GNU/Linux OS Version $ cat /etc/os-release PRETTY_NAME="Raspbian GNU/Linux 12 (bookworm)" NAME="Raspbian GNU/Linux" VERSION_ID="12" VERSION="12 (bookworm)" VERSION_CODENAME=bookworm ID=raspbian ID_LIKE=debian HOME_URL="http://www.raspbian.org/" SUPPORT_URL="http://www.raspbian.org/RaspbianForums" BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs" CodeSys runtime 4.13.0.0 So far we tested runtime versions up to 4.18.0.0, here are the results : * 4.13.0.0 --> Not working ❌ * 4.14.0.0 --> Not working ❌ * 4.15.0.0 --> Not working ❌ * 4.16.0.0 --> Not working ❌ * 4.17.0.0 --> Working ✅ * 4.18.0.0 --> Working ✅ There is nothing in the 4.17.0.0 release note that mentions that, so I'm not sure what to think about this. Is this a known problem within the CodeSys development team ? If yes, how do you follow CM4 hardware evolutions ? Is there a way of making this work without having to update the runtime version ? We have several products working with the 4.13.0.0 runtime and we would like to avoid having to update them all. BR
Last updated: 2026-02-02

Post by mondinmr on COL.IMap2 and HashTableFactory cause frequent Access Violation ^{CODESYS Forge talk (Post)}
Good morning, I’ve been using the Collection library for a long time, mostly with Stack, LinkedList, and List. From your examples I was able to manage the different factories, even for custom elements. Now I need a hashtable, but with this object I’m running into a lot of random access violations. If I append something inside FB_Init after constructing the hashtable, it crashes, even though the list was already created. If I only create the hashtable in FB_Init and append afterwards, it usually works. I don’t understand the meaning of the dispose call in this code: pSlave := ADR(slave); uSlave := TO_ULINT(pSlave); iKey := fKey.Create(uSlave); IF hash.CountKeys() = 0 THEN Service.logger.appendLog('Filling hashtable', 'HashManager', AdvLogType.AdvDebugMsg); ok := FALSE; ELSE eError := hash.ContainsKey(iKey, xResult => ok); END_IF IF NOT ok THEN pI := __NEW(UINT); iVal := fKey.Create(TO_ULINT(pI)); Service.logger.appendLog(CONCAT('New slave', TO_STRING(uSlave)), 'HashManager', AdvLogType.AdvDebugMsg); hash.AddKeyValuePair(iKey, iVal); appendNewSlave := pI; ELSE eError := hash.GetElementByKey(iKey, itfValue => iElem); xResult := __QUERYINTERFACE(iKey, itfIInstance); IF xResult THEN itfIInstance.Dispose(); END_IF IF eError <> COL.COLLECTION_ERROR.NO_ERROR THEN Service.logger.appendLog(CONCAT('ERROR ', TO_STRING(eError)), 'HashManager', AdvLogType.AdvCriticalMsg); appendNewSlave := nullptr; RETURN; END_IF __QUERYINTERFACE(iElem, iVal); {warning disable C0033} pI := TO___UXINT(iVal.UlintValue); {warning restore C0033} appendNewSlave := pI; END_IF Without the dispose call, every second cold reset crashes immediately when I try to access iVal, even if eError doesn’t report any error. With the dispose call, the cold reset issue disappears, but I get other problems: a) If I start the runtime using systemctl start codesyscontrol, it crashes at IF hash.CountKeys() = 0 THEN b) If I delete the files in PlcLogic and download again, it works and survives multiple cold resets. But as soon as I run systemctl restart codesyscontrol, everything gets corrupted again and it starts crashing at that point. FUNCTION_BLOCK SlaveMapCounter VAR hash : COL.IMap2; eError : COL.COLLECTION_ERROR; END_VAR In its FB_Init I create it: METHOD FB_Init: BOOL VAR_INPUT bInitRetains: BOOL; // TRUE: retain variables are initialized (reset warm / reset cold) bInCopyCode: BOOL; // TRUE: the instance will be copied to the copy code afterward (online change) END_VAR VAR hF : COL.HashTableFactory; END_VAR hash := hF.Create(256); In another FB I instantiate it statically: FUNCTION_BLOCK ABSTRACT AbstractServoEthercatController EXTENDS AbstractServoController VAR_STAT hashSlaves : SlaveMapCounter; END_VAR VAR field : REFERENCE TO ADVAbstractFieldUnitEthercatCia402; initCnt : REFERENCE TO UINT; END_VAR The append method is the one shown above, and I call it after the runtime has started. The accesses are performed by a single task, and in any case I’m working on an isolated single core. I’ve tried everything, moving the create, the instances, and all the rest several times, but nothing seems to work. I’d like to point out that these FBs are part of our own library, which is used in many applications.
Last updated: 2025-09-11

Post by cfam on Codesys Control for PLCnext (PLC - AXL F 2152) ^{CODESYS Forge talk (Post)}
Good day All I would like to share some information on this site for the Codesys team as well for the future members using Codesys Control for PLCnext if it is allowed. I hope that i Post it in the correct spot. Subject: Codesys, Codesys Control for PLCnext Objective: Using the following Phoenix components to built a PLC Rack and run it on Codesys: Hardware and Software used 1. 2404267, AXC F 2152 - Controller 2. 1088136, AXL F BP SE6 - Module carrier 3. 1088129, AXL SE DO16/1 - Digital module 4. 1337224, AXL SE PD16 GND - Potential distributors 5. 1088127, AXL SE DI16/1 - Digital module 6. 1337223, AXL SE PD16 24V - Potential distributors 7. 1088123, AXL SE AO4 I 4-20 - Analog module 8. 1088134, AXL SE SC-A - Cover 9. Codesys v3.5 SP19 Patch 4 10. Codesys Control for PLCnext V4.10.0.0 Process: Firstly I built the Rack according to the Phoenix Project+ Software tool. Where I rebuilt it onto my test bench . I used the PLCnext Engineer IDE from Phoenix and all Communications where up and running and my PLC program executed successfully. THEN I tried the same PLC Layout with Codesys and Codesys Control for PLCnext. It was not successful and gave me the "Error: Local Bus not Running". I searched the web for answers but was unsuccessful in finding a solution. So I tried to change my configuration and found that the following Modules COULD NOT be recognized by Codesys Control. The result was that the Local Bus Failed to run. 1337224, AXL SE PD16 GND - Potential distributors 1337223, AXL SE PD16 24V - Potential distributors Example 1, Resulted in "Error: Local Bus Not Running": Module carrier slot 1: 1088129, AXL SE DO16/1 - Digital module Module carrier slot 2: 1337224, AXL SE PD16 GND - Potential distributors Module carrier slot 3: 1088127, AXL SE DI16/1 - Digital module Module carrier slot 4: 1337223, AXL SE PD16 24V - Potential distributors Module carrier slot 5: 1088123, AXL SE AO4 I 4-20 - Analog module Module carrier slot 6: 1088134, AXL SE SC-A - Cover Example 2, Result "Successful": Module carrier slot 1: 1088129, AXL SE DO16/1 - Digital module Module carrier slot 2: 1088127, AXL SE DI16/1 - Digital module Module carrier slot 3: 1088123, AXL SE AO4 I 4-20 - Analog module Module carrier slot 4: 1088134, AXL SE SC-A - Cover Module carrier slot 5: 1088134, AXL SE SC-A - Cover Module carrier slot 6: 1088134, AXL SE SC-A - Cover Result: Codesys or Codesys Control for PLCnext, has a PROBLEM to identify the following Modules. 1. AXL SE PD16 24V - Potential distributors 2. AXL SE PD16 GND - Potential distributors Hope that this information could be useful in future. Best regards Jaco Pretorius
Last updated: 2023-12-06

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Hello everyone, I have a very simple program for the process, but it's driving me crazy and I can't see the problems I'm left with: Short topological description: Dual Core Berghof controller with softmotion runtime version 3.5.19.30; Two axes with servodrive on canopen bus, clocked distributed from master; Ethercat I/O node; 2 ms ethercat task, 2 ms canopen bus cycle time; I/O objects of the canopen master and canopen drives connected to the ethercat task cycle; Problem 1: Two separate programs each manage their own axis and drive, with separate state machines. A first axis moves primarily in velocity, except having to position itself absolutely at a predetermined point at the end of the job; the second axis, on the other hand, is a paper unwinder that changes, for each job cycle, from actions in absolute, relative, and cam displacement with the master axis. Well, the state machine of both axes was written in such a way as to call running the useful FB and change it on state change in this way: CASE i_stateMachine OF 0: o_Power(Enable := TRUE, bRegulatorOn := FALSE, bDriveStart := FALSE, Axis := o_PaperUnwinderAxis); o_MoveAbs(Execute := FALSE, Axis := o_PaperUnwinderAxis); o_MoveRel(Execute := FALSE, Axis := o_PaperUnwinderAxis); o_CamSelect(Execute := FALSE, Master := o_MachineAxis, Slave := o_PaperUnwinderAxis, CamTable := cam_PaperUnwinder); o_CamIn(Execute := FALSE, Master := MachineEncoder, Slave := o_PaperUnwinderAxis); o_CamOut(Execute := FALSE, Slave := o_PaperUnwinderAxis); o_SetPosition(Execute := FALSE, Axis := o_PaperUnwinderAxis); IF ... THEN i_StateMachine := 10; END_IF; 10: o_Power( Enable := TRUE, bRegulatorOn := TRUE, bDriveStart := TRUE, Axis := o_PaperUnwinderAxis ); IF o_Power.Status THEN i_StateMachine := 20; END_IF; 20: (* Avanzamento carta *) o_MoveAbs( Execute := TRUE, Position := o_Somewhere, Velocity := 25.0, Acceleration := 3666.7, Deceleration := 3666.7, Jerk := 48000.0, Direction := MC_DIRECTION.positive, Axis := o_PaperUnwinderAxis ); IF o_MoveAbs.Done THEN o_MoveAbs(Execute := FALSE, Axis := o_PaperUnwinderAxis); i_StateMachine := 30; END_IF 30: d_HomingPosition := ...; o_SetPosition( Execute := TRUE, Position := d_HomingPosition, Mode := FALSE, Axis := o_PaperUnwinderAxis ); (* ... *) IF o_SetPosition.Done = TRUE THEN o_SetPosition(Execute := FALSE, Axis := o_PaperUnwinderAxis ); o_LogServer.Append(sMessage := '...', lscClass := LOGSERVER_CLASS.ALWAYS, sdt := o_CommonsMgrData.systime.sdtLocal); i_StateMachine := 40; END_IF; 50: ... The code above is a sketchy example of what I wanted to write. But it gives me a spot problem: in some, the state change results in a drive error, which is unrecoverable except with a reinitialization via SM3_ReinitDrive(). Things are improved a little if in the program I always run the call of all softmotion blocks in this way: o_Power(Axis := o_PaperUnwinderAxis); o_Jog(Axis := o_PaperUnwinderAxis); o_Halt(Axis := o_PaperUnwinderAxis); o_MoveAbs(Axis := o_PaperUnwinderAxis); o_MoveRel(Axis := o_PaperUnwinderAxis); o_CamIn(Master := MachineEncoder, Slave := o_PaperUnwinderAxis); o_CamOut(Slave := o_PaperUnwinderAxis); If I don't execute all the calls of all the motion FBs used, when exchanging machine state often (but not always), the axis goes into error with event id THE_FB_WASNT_CALL... Done a little diagnostics it seems that the FBs return the bDone, before they are completely terminated. I tried doing the machine state exchange not with the bDone bit of the FBs, but with the 'standstill' state of the axis. It didn't seem to change anything. Problem 2: During the use SM3_ReinitDrive() I get the erro in the log: "NetID 0: SDO read error for object 16#607C..." Assuming that the device involved it's one of the two servodrive, (no others device are present in the network), I don't found any object 0x607C in the 'possible object list in/out' of the two drive, and I don't understand where this object can be listed. So any ideas and suggestions regarding these two issues will be very, very welcome. If you need the source project, I am willing to send it.
Last updated: 2024-07-17

Post by vstrom on Codesys v3.5.22.10 - Internal error:System.AggregateException...Value cannot be null...Parameter name: expLValue ^{CODESYS Forge talk (Post)}
Hi to all, I receive an error when I try to compile a project that in v.3.5.21.50 have no problem. The error seems to comes out when I add the Visualization part into the project. The complete error is: [ERROR] Internal error:System.AggregateException: One or more errors occurred. ---> System.Exception: Internal error in Code ---> System.ArgumentNullException: Value cannot be null. Parameter name: expLValue at _3S.CoDeSys.LanguageModelManager.LanguageModelBuilder.CreateAssignmentExpression(IExprementPosition pos, IExpression expLValue, IExpression expRValue, Operator kindof) at _3S.CoDeSys.LanguageModelManager.LanguageModelBuilder.CreateAssignmentStatement(IExprementPosition pos, IExpression expLeft, IExpression expRight) at ..
(IExpression , IExpression ) at ..
(_IAssignmentExpression ,  ) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.AssignmentStatementReplacer.ReplaceExpressionStatement(_IExpressionStatement expressionStatement, _ICompiledPOU cpou) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_IIfStatement ifst) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_IIfStatement ifst) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_IForStatement forloop) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at ..
(_ICompiledPOU ) at ..(_ICompiledPOU ) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Codegeneration.
(_ICompiledPOU , _ISignature ) at ..
(_ICompiledPOU ) at ..
(_ICompiledPOU& ) at ..
() --- End of inner exception stack trace --- --- End of inner exception stack trace --- at _3S.CoDeSys.Compiler35220.CompilerPhases.CompilerPhase5_Codegenerator.
(IList1 ) at _3S.CoDeSys.Compiler35220.CompilerPhases.CompilerPhase5_Codegenerator.
(IScope5 , IList1 ) at _3S.CoDeSys.Compiler35220.CompilerPhases.CompilerPhase5_Codegenerator.
(ICodegenerator ) at _3S.CoDeSys.Compiler35220.CompilerPhases.CompilerPhaseControllerGenerateCode.() at _3S.CoDeSys.Compiler35220.CompilerPhases.CompilerPhaseControllerGenerateCode.() ---> (Inner Exception #0) System.Exception: Internal error in Code ---> System.ArgumentNullException: Value cannot be null. Parameter name: expLValue at _3S.CoDeSys.LanguageModelManager.LanguageModelBuilder.CreateAssignmentExpression(IExprementPosition pos, IExpression expLValue, IExpression expRValue, Operator kindof) at _3S.CoDeSys.LanguageModelManager.LanguageModelBuilder.CreateAssignmentStatement(IExprementPosition pos, IExpression expLeft, IExpression expRight) at ..
(IExpression , IExpression ) at ..
(_IAssignmentExpression ,  ) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.AssignmentStatementReplacer.ReplaceExpressionStatement(_IExpressionStatement expressionStatement, _ICompiledPOU cpou) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_IIfStatement ifst) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_IIfStatement ifst) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_IForStatement forloop) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Optimization.ExpressionStatementReplacerVisitor.visit(_ISequenceStatement sequenceStatement) at ..
(_ICompiledPOU ) at ..(_ICompiledPOU ) at _3S.CoDeSys.Compiler35220.Phase5_Codegeneration.Codegeneration.
(_ICompiledPOU , _ISignature ) at ..
(_ICompiledPOU ) at ..
(_ICompiledPOU& ) at ..
() --- End of inner exception stack trace ---<---
Last updated: 2 days ago

Post by deeps on web visu on IFM ^{CODESYS Forge talk (Post)}
I have an IFM cr1077 display. I would like to show B&R mapp view on IFM visualization. I used coedsys web browser elemnt for this. I could see IFM working fine in Internet web browser but IFM device shows white screen and freezes. I think there is problem with IFM showing the web browser. Is my understanding of the web visu right? am I doing any mistake here?
Last updated: 2023-08-18

Post by arnog on Two drives on one axis, Gantry Robot ^{CODESYS Forge talk (Post)}
Hi TK_Jenssen did you found a solution I am setting up the samelike gantry only with two z-axes which are mounted on fix position with an X axes between the two z-axes. The movement and position of both z-axes must be very well aligned and calibrated. Maybe also to be adjusted by programming. Can you sent an example of your solution?
Last updated: 2023-08-25

Post by john-ronald on Communication error (#0), logout performed,please check if plc is connected ^{CODESYS Forge talk (Post)}
Hi, I have the same problem. However I am using ethernet connection not USB. I can ping the PLC and also connect to it via Wago ethernet settings, but I cannot upload using the Codesys 2.3. My PLC is Wago 750-862. The detailed error is - " connect: Connection refused Write attempt from invalid socket. " Any help would be appreciated.
Last updated: 2023-09-11

Post by transmin01 on PCAN serial "No CAN driver found" ^{CODESYS Forge talk (Post)}
Hi, I am using a PCAN mini CAN board which has the Windows drivers installed on the target PLC. PCAN board can be seen in device manager. However, I am getting "No CAN driver found" error. I have read the post https://forge.codesys.com/forge/talk/CODESYS-V2/thread/44aae19318/ and have uncommented the CmpPCANBasicDrv driver in the CodesysControl.cfg file in development PC and have copied it to the target PC. Current CodesysControl.cfg file attached. Is there anything else I am missing? Regards
Last updated: 2023-09-14

Post by manuknecht on Detect "Cancel" Press in FileOpenSave Dialog ^{CODESYS Forge talk (Post)}
When using the FileOpenSave dialog and using the Visu_FbFileListProvider FB as an In/Output I could not manage to detect the difference of pressing the "Load" button on the dialog vs. pressing the "Cancel" button. In both cases, the selected file is updated if the dialog is closed when checking using the Visu_FbFileListProvider.GetSelectedFileName() command. How can I prevent reading or writing of a file when the "Cancel" button was pressed?
Last updated: 2023-09-19

Post by damian177 on Codesys and SMS in RPi ^{CODESYS Forge talk (Post)}
Hi, I try use IIoT library to send and receive SMS by Raspbery PI and Codesys. I installed IIoT package and added the SMS library, But something is wrong, when I init communication it doesn't work, When I sniffer my communication (AT commands) beetwen RS232 RaspberryPi and my GSM modem I have only below commands: AT+CMEE=1 OK AT+CPIN? +CPIN: READY Anyone have idea what can be wrong ?
Last updated: 2023-09-28

Post by sukrit on What licenses are required for runtime on raspberry pi cm4 ^{CODESYS Forge talk (Post)}
We have developed a project for 2 servo motors using raspberry pi computemodule 4 on ethercat master. we are using web visualization for display different screens. project is running well in demo. we want to implement it in production envoirment. being new still wondering which licences i need. Can We get this information in codesys devlopment software. code size is approx 5 mb, 1 instance of etharcat master and aproox 100 variables in visaualization.
Last updated: 2023-10-17

Post by simotion on Online view : code is scanned ^{CODESYS Forge talk (Post)}
If I do online monitoring of code in f.i. a function block, I cannot see if the function block is called or not. In software from other vendors you normally have an indication if the online code you are looking on is scanned at that moment or not. Is there a way in Codesys to determine in the online view if (parts) of the code are scanned or not? Thanks
Last updated: 2023-10-23

Post by ekristoffe on Beispieldateien finden / Inhalt der Packages ^{CODESYS Forge talk (Post)}
Hello @eschwellinger, Why not using one of those 2 folders: C:\ProgramData\CODESYS C:\Users\Public\Documents\CODESYS The main reason is depending on the company and the user right, the end user may not have the access to use those folders. Also having a non version dependent folder may help if the end user uninstall a previous version and forgot all its sample project where in this previous version installation. Thanks.
Last updated: 2023-11-24

Post by simotion on Inheritance of axis ^{CODESYS Forge talk (Post)}
I have developped a function block 'Axis' the inherits from 'AXIS_REF_SM3' -> FUNCTION_BLOCK Axis EXTENDS AXIS_REF_SM3 In my global variable list I define a variable MasterDrive of type Axis and assign Axis1. Axis1 is a virtual drive (AXIS_REF_VIRTUAL_SM3). This type should inherit from AXIS_REF_VIRTUAL. VAR_GLOBAL MasterDrive : Axis := Axis1; However I get the error 'Cannot convert type'. What is the way to obtain what I want : function block inheriting AXIS_REF_SM3 and initialising this function block with a Softmotion virtual or real axis?
Last updated: 2023-12-07

Post by andre-luis on Check if Codesys runtime is on 'Running' or 'Stopped' state? ^{CODESYS Forge talk (Post)}
Just to share, for those who as me are seeking for this and had found no information anywhere in this World: Every time I stop/start the PLC runtime ( turning into 'Stopped' or 'Running' state ) the 'CODESYSControlService' appears at the Taskmanager list, which could suggest a straight correlation. I was expecting a clever solution, but this one solves for while.
Last updated: 2024-07-02

Post by nano on Issues with Modbus Slave with Raspberry Pi ^{CODESYS Forge talk (Post)}
in the codesyscontrol.cfg or codesyscontrol_user.cfg you have to declare whoch comport-ports from runtime are used. please tell us how the comport is called in linux an post the codesyscontrol.cfg files also write down here, which parameters are used in the python-script and what is parameteized in the modbus-master-comport of your codesys-application. mostly the errors occurs in ine of these areas
Last updated: 2024-07-11

Post by taqamert on Codesys 2.3 & Peak PCAN ^{CODESYS Forge talk (Post)}
Despite working on it for days, I haven't achieved any results. I followed the necessary steps one by one as mentioned in the file you sent, but there hasn't been the slightest change. I couldn't find the step you mentioned "Set the 'Can Board Type' to PCAN USB" in the Word document. There is no such setting anywhere I looked. Is there a more detailed explanation available, or can you explain it in more detail? What am I missing?
Last updated: 2024-07-16

Post by kislov on Change modbus server parameters from program ^{CODESYS Forge talk (Post)}
Use in IEC-code: Modbus_Serial_Device.UpdateComPortSettings(...) https://content.helpme-codesys.com/en/libs/IoDrvModbusSerialSlave/Current/pou-ModbusSerialDeviceDiag/UpdateComPortSettings.html Take note: "Only possible if server is disabled (see xEnable Input)" So: Modbus_Serial_Device.xEnable := FALSE; Modbus_Serial_Device.UpdateComPortSettings(...) Modbus_Serial_Device.xEnable := TRUE; Please note that after PLC reboot the values from the GUI (from your screenshot) will be applied again. So you need to save values from HMI in RETAIN and restore them after start of application.
Last updated: 2024-07-17

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Yes, this point is part of my misunderstanding. Why, after the execution ot the motion FBs is set to FALSE and exsecuted at lest one time, it must be continuosly called, even if the motion control it's take from another subsequent instruction. This is what I really don't undertand, but what in fact it's happening. For example, in case of stopping a MoveVelocity FB, then Halting the motion by the related FB, the axis at spot goes into error. If there was bad trigger management, the various instructions would NEVER work.
Last updated: 2024-07-18

Post by schweizer on Position und Größe optimal anpassen (Container.Height - Visu.Height) funktioniert nicht. ^{CODESYS Forge talk (Post)}
Hello forum Does anyone have experience with optimally adjusting the position and size of the visualization elements? For us, the adjustment on the x-axis works in Codesys 3.5 SP20 with (Container.Width - Visu.Width). However, the y-axis is not affected with (Container.Height - Visu.Height). We implemented this according to the example from Codesys "Optimally adjust position and size" and had no success. Thank you very much for your help.
Last updated: 2024-07-29

Post by pavanifm on Test a manager script (.tsd file{xml document}) not starting from Git CI heedlessly/ without ui ^{CODESYS Forge talk (Post)}
'--noUI' option of Command line interface for test manager test script not executing when triggered from CI as well as from Local PC however is it working for execution of python scripts from CLI. can we start codesys test manager scripts from CLI interface without any GUI in background process of windows? i can see simlillar questions asked but no answer yet. otherwise, what is the solution to built test automation framework using Test Manager & GIT CI/CD?
Last updated: 2024-08-07

Sort by relevance or date