Post by toby on SM Drive license error ^{CODESYS Forge talk (Post)}
Hi albert1999 and forest, I hope you are well. I too am wondering if you have found any solutions? Im working with a RPi and a Omron R88D-ETH servo amplifier. The SoftMotion is timing out after 30min without the license, but I cant figure out how to license it, and I seem to have some compatibility issues between my RPi license and any SoftMotion licenses. Did you guys have any luck? Thank you very much for any assistance offered. Toby
Last updated: 2024-01-10

Post by wehling-h on PI Input value ^{CODESYS Forge talk (Post)}
Hi geoweil, have you tried to save changed values to remanent area or using a VAR RETAIN? After restart you have to initialize Counter with last remanent value. Depending on changes per cycle and the possibilitiy of your control unit to write remanent storage. Otherwise you need a buffering system to ensure save backup of last PI_Counter value. May you could read this Thread to get further help: https://forge.codesys.com/forge/talk/Engineering/thread/31e1c8349e/#bf48
Last updated: 2024-01-12

Post by hsmw-wolf on How to fix Codesys Simulation Exception ? ^{CODESYS Forge talk (Post)}
Did anybody have a solution for this problem? I have the same issue and it occured as i wanted to continue work after the weekend. On Friday the simulation was working fine and on Monday thise error appears. There should be a more specific fault description to be honest. As I am writing I try to repair the installation and hope, that this will work. Still I am frustrated, because I don't know where to look for eliminating this fault. I am using CODESYS 3.5 SP19 Patch 5.
Last updated: 2024-01-29

Post by durstloescher on Codesys Input Detector ^{CODESYS Forge talk (Post)}
Good morning, I am currently working on implementing a display dimmer. I want the display to dim after X minutes. This works so far. The implementation is done via the Linux subsystem, to which a command is sent to dim the display. However, my problem is resetting the timer when input is received. I want the dimming timer to be reset with each click/touch. Unfortunately, I can't find a suitable solution for this. Are there any ways to do this? Codesys v3.5 SP19 Patch 2
Last updated: 2024-02-15

Post by kleeswi on SysFileOpen does not work after update to V3.5 SP19 Patch 5 ^{CODESYS Forge talk (Post)}
I use the function SysFile.SysFileOpen(sFileNamePara, SysFile.ACCESS_MODE.AM_WRITE, pErrorFileOpen); to open and write a file. Since the update from Codesys V3.5 SP17 to V3.5 SP19 Patch 5 it does not work anymore. I first had SysFile.SysFileOpen(sFileNamePara, SysFile.ACCESS_MODE.AM_APPEND_PLUS, pErrorFileOpen); in both versions. hFile_Test is a pointer to byte. It gives an exceptional error when dereferencing the hFile_Test pointer. Edit: I use Codesys on a Raspberry pi
Last updated: 2024-02-19

Post by timvh on IFM CR711S Version Mismatch ^{CODESYS Forge talk (Post)}
You should ask IFM to provide you with the correct version of their controller packages. Then after you have installed this, you can select the correct version of the controller by right clicking on it in the device tree, update device, enable the option "Display all versions" and then select the version which matches your controller. Alternatively you can ask IFM to provide an update package which can update the runtime version on your controller to 3.2.0.0.
Last updated: 2024-03-05

Post by k4zz on Continuous Build Server ^{CODESYS Forge talk (Post)}
Hallo Martin, Thank you so much for the Code example. It works really fine for .porject Types. However, I encountered a challenge when attempting to apply it to .library Types. I also tried the option to "Perform static analysis automatically after compilation" # get Project values myProject = projects.primary # Creates an active application app = myProject.active_application # build Application and run static code analysis app.generate_code() Could you please offer any insights into why this might be occurring?
Last updated: 2024-03-15

Post by wollvieh on Problem while updating to new runtime 4.11.0.0 ^{CODESYS Forge talk (Post)}
okay, no ideas. So i made a new fresh image for the raspberry, so far,so good. Licensing the new image was no problem. And, after having trouble while read write files on the raspberry pi, i found the solution for these file operations with the Variable ForceIecFilePath in the CODESYSControl.cfg file. Some people had that issue discussed in that thread : https://forge.codesys.com/forge/talk/Deutsch/thread/d2df08e587/
Last updated: 2024-03-18

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi everybody We are currently working on a project with an RS232 serial COM interface and using the CAA SerialCOM library. We have it working fine reading and writing data, although we have found an issue we cannot resolve and any suggestions would be helpful. We have noticed that after a while the RS232 stops working. We have tracked this down to the HANDLE hCom keeps increasing and when this reaches 1023 the COM returns an unknown error "5003". Is there a way to reset this hCom reference? Thanks Richard
Last updated: 2024-03-22

Post by remcoborghuis on C0032 Error to type Pointer to IoConfigParameter ^{CODESYS Forge talk (Post)}
Hi All, I'm using codesys on a raspberry PI. I use V3.5 SP18 Patch 2 development system and codesys for raspberry pi 4.8.0.0. Sometimes when I build the project I get error messages C0007: Expression expected instead of ',' and C0032: Cannot convert type 'Unknow type: '!!!'ERROR'!!!" to type 'POINTER TO IoConfigParameter'. I can't click on the message to bring me to the fault. After I do a "Clean all" the build finishes successful. Anyone who can help me with this problem? Thanks! Remco Borghuis
Last updated: 2024-03-25

Post by carohe on VisuNamespace != null ^{CODESYS Forge talk (Post)}
Hello, this error occured frequently over the past couple of weeks. I found out, when adding a webvisu, CODESYS added Visu libraries in the library manager. One of the libraries was the "VisuElemsAlarm" library. In my case it added this one with the version 4.3.0.0. However another library that also contained the "VisuElemsAlarm", used the "VisuElemsAlarm" with the version "4.4.0.0". After changing the Version "4.4.0.0" and uninstalling this version, the error has not occured anymore. Regards, carohe
Last updated: 2024-04-02

Post by installwhat on raspistepper error after install ^{CODESYS Forge talk (Post)}
I've had issues getting the raspistepper installed, all due to errors upon installation. The closest I get is the pictured error. The functions are in the sm3_shared library. I can add this library but that leaves 2 issues. I don't actually know, and I really want to understand this, why the required dependencies haven't been installed correctly. If I add the library it's only available with through the namespace. What can I do to both understand and resolve this? Thanks edit codesys 64 3.5.20.0 - same error on other versions too sm3 raspi stepper 0.0.0.5
Last updated: 2024-04-20

Post by dkugler on Alarm State Icon ^{CODESYS Forge talk (Post)}
thank you for pointing me to this "bug"!! I haven't recognized, the bit is reset after the first alarm is gone. I use this only for warnings, so it's not a drama, but was not correct in the past. I solved it now simply stupid by counting up a variable every time an alarm appears and decreasing it if an alarm is gone. The "warning lamp" is activated by checking the counter is > 0 The nice side effect, i'm able to show the number of active alarms in the state line now.
Last updated: 2024-04-24

Post by yongchaow on Can't connect to Device Raspberry Pi 4 from CODESYS IDE V3.5 SP19 ^{CODESYS Forge talk (Post)}
Hi, eschwellinger, I have the same problem, but I can not resolve the problem following this forum. There are my situation: pi@RevPiXXXX:~ $ uname -a Linux RevPiXXXX 5.10.120-rt70-v7l #1 SMP PREEMPT_RT Thu, 28 Jul 2022 10:36:48 +0200 armv7l GNU/Linux After "top": It looks like runtime is not running. One more piece of information to refer to, when I reboot the device it is possible to scan the device. Looking forward your reply.
Last updated: 2024-04-25

Post by yannick on Raspberry PI 5 not working ^{CODESYS Forge talk (Post)}
Hello I'm using Codesys V3.5 SP19 Patch 6 and a Raspberry PI 5 4GB Bookworm 32bit with the Runtime 4.11.0.0 SL. I can install the runtime and download the software completly but after a few seconds the connection disconnects with the message no connection to device. Please scan network again. And the object reference was not set to an object instance. See screenshot. Can somebody help me with that? Thanks
Last updated: 2024-04-28

Post by richard-wang on Codesys recipe manager - what does it do? ^{CODESYS Forge talk (Post)}
Hi All Thanks for sharing this information. For whom may not know why always get error code 16#4000 or 16#4002 while performing Recipe commands, the root cause is There is a line need to be inserted in CODESYSControl.cfg file, which is PlaceholderFilePath.1=/var/opt/codesys/PlcLogic/ I am using Pi, therefore the above path is set to my pi unit, after adding above line to my cfg file, all the Recipe commands work fine. But I still do not know how and when this file got modified though.
Last updated: 2024-04-29

Post by tomas111 on OPC UA Client API ^{CODESYS Forge talk (Post)}
I ran into a problem. Uploaded an example (https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_uacapi_example.html) After launch. on the emulator. I see that I am having problems: - UaExpert does not connect. There are many servers but no connection. - I can’t transfer the certificate from quarantine to trusted ones. There is some problem with creating the certificate. CS 19.2. If anyone has had similar problems, please give me advice. Thank you.
Last updated: 2024-05-20

Post by plunje on Sensor not set ^{CODESYS Forge talk (Post)}
A got a larger project but this very small example makes it clear. I have a button, and after it's clicked a lamp should flip on and stays on, and when the mouse-button is released it should stay on. When I try that in the PLC_PRG it works, but when I change it to a function block (seet attched demo proj) it isn't. I'm fairly new to PLC programming but are very experienced C# engineer, but this goes above my head...
Last updated: 2024-05-26

Post by installwhat on C0077 on one machine but not another ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/92c913bf7c/ Solved by changing the ethercat master version after reading the thread linked above. I think I need to read up on why this happened. I understand that placeholders should point to a particular version for obvious reasons however what has occurred in this instance is different. The example project was released as a "project archive" but it seems to load differently based on what I've got installed in my repositories. I'm going to dig into that tomorrow but any advice is welcome.
Last updated: 2024-06-11

Post by kenth1973 on MC_Phasing state explenation ^{CODESYS Forge talk (Post)}
My MC_Phasing FB was stuck in iPhasingState=1 and error output HIGH on one axis. I could manually overwrite the state to 0 in the instance data. During normal run I see the state change from 0 to 10 to 100 back to 0 (maybe more states that I couldnt catch with the naked eye) But - what are the states numbers and their different explenations? This is not explained in the FB guide on codesys. (the pictures show state = 0 after I reset)
Last updated: 2025-11-22

Post by antonz on OSCAT Scale_r function not working in LD 4.60 works in LAD2 on 3.5.21sp3 ^{CODESYS Forge talk (Post)}
That's what I found as well Shaun. I have seen it at least in versions 3.5.21.1 and 3.5.21.3. There seems to be an issue with the FBD/LD package v4.6.0.0. The workaround proposed by Tim works but needs to be done manually on every code change/addition. For now we manually downgrade the FBD/LD package from v4.6.0.0 down to v4.5.0.0 after installation of CoDeSys. Same as you did. I hope this gets fixed on a next patch.
Last updated: 2025-11-21

Post by gseidel on Scara3 kinematic robot error ^{CODESYS Forge talk (Post)}
Hi aniket-b, the maximum cycle time of the EtherCAT_Task is very high, ca. 35 ms. Could you please check if this is just the first cycle after starting the application or if it happens during motion? (You can reset the times in the task configuration by right-clicking in the "monitoring" tab.) Another thing to try: put the SoftMotion_Planning task on a different core. Best regards, Georg
Last updated: 2026-01-07

Post by suyash on Device User Logon ^{CODESYS Forge talk (Post)}
Thanks for your reply @eschwellinger. Update : the is problem is resolved. It was done by renaming the User database file (/var/opt/codesys/.UserDatabase.csv) as deleting it was risky. After restart the IDE asked me to create new user. On doing that the problem got resolved. Reference for members facing similar problem/s : sudo systemctl stop codesyscontrol sudo mv /var/opt/codesys/.UserDatabase.csv_ /var/opt/codesys/.UserDatabase.csv_.old sudo systemctl start codesyscontrol
Last updated: 2026-05-14

Post by charly29160 on WebVisu scaling regression in V3.5.22 P2: frame size jumps when switching visualizations ^{CODESYS Forge talk (Post)}
Environment: - CODESYS V3.5.22 Patch 2 - CODESYS Control for Raspberry Pi MC SL - WebVisu in browser Problem: When switching between visualizations using a Register element (Registerkarten), the displayed frame size jumps incorrectly after returning to a previously viewed visualization. This behavior was introduced in V3.5.22 Patch 2. The same project worked correctly in V3.5.21 Patch 4. WebVisu settings in V3.5.21 (working): - Scaling: Isotropisch - Automatisch ermittelte Clientgröße verwenden: active - All visualizations: Automatisch erkannte Visualisierungsgröße Workaround?
Last updated: 2026-06-15

Post by winki on Error in licence activation ^{CODESYS Forge talk (Post)}
Hello, Despite receiving an activation message after entering the license number, I don’t have any license installed on my gateway. I went to check in /var/opt/codesys/ and there is no License file. I searched the entire gateway for a .lic file and found no license. I’m really stuck—how can I fix this, please? When I am using the licence tools I got this picture: But nothing that have been activated. Loic,
Last updated: 2026-02-03

Sort by relevance or date