Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device
CODESYS Forge
talk
(Post)
Hello, CODESYS Control is running on my RevPi, and my system communicates over a CANbus with a master using the ConnectCan module (Slave - CANopen Device). The communication works perfectly fine so far. However, as soon as I call a Python script with "SysProcessExecuteCommand2" that creates a CSV file and executes without errors, the master does not adopt any changes to the Transmission Process Data Objects (TPDOs). I don't quite understand what one has to do with the other, and perhaps someone can help me with this. Here is my script call: SysProcess.SysProcessExecuteCommand2(pszCommand:='python /home/pi/test.py', pszStdOut:=sCMDOutput, udiStdOutLen:= SIZEOF(sCMDOutput), pResult := ADR(eResult)); Thank you in advance! Best regards, Stefan
Last updated: 2024-06-20
Post by imdatatas on Codesys IDE initialization error from a new Sandbox image
CODESYS Forge
talk
(Post)
Hello everyone, I created a new sandbox image on the D drive with Codesys Installer. However, when I launch the IDE from this image, it gives the error shown in the attached image. -- Codesys V3.5 SP19 Patch7. -- The installer is the latest (2.5.0). -- All packages in the installer were updated to the latest version as of today when creating the sandbox. -- The originally installed IDE on the C drive does not give this error when launched. -- I last upgraded it to Softmotion 4.20.1.0 through the installer. Has anyone encountered the same or a similar issue? Will this issue be fixed in the next update? Best regards, Imdat
Last updated: 2025-12-05
Post by aleksahin6824 on SysEthernet error
CODESYS Forge
talk
(Post)
Good afternoon Please help with localizing the error. Periodically, but on the same time grid, the error SysEthernet: packet could not be sent occurs. PLC and motors from XINJE. PLC — XSA-330L, rev. 1.2, drivers — DC5C2 (rev.5) In the task configurator, all tasks are set to simple numbers (11, 13, 41 ms) for convenience. The jitter for EtherCat and SoftMotion tasks is less than the task cycle (2 ms jitter for a 6 ms task). The power supply is sufficient for both the PLC and the motors. The cables are in good condition. Please suggest where to look for the problem. P.S. The PLC uses proprietary Linux and there is no SSH access.
Last updated: 2026-08-30
Post by aleksahin6824 on SysEthernet error
CODESYS Forge
talk
(Post)
Good afternoon Please help with localizing the error. Periodically, but on the same time grid, the error SysEthernet: packet could not be sent occurs. PLC and motors from XINJE. PLC — XSA-330L, rev. 1.2, drivers — DC5C2 (rev.5) In the task configurator, all tasks are set to simple numbers (11, 13, 41 ms) for convenience. The jitter for EtherCat and SoftMotion tasks is less than the task cycle (2 ms jitter for a 6 ms task). The power supply is sufficient for both the PLC and the motors. The cables are in good condition. Please suggest where to look for the problem. P.S. The PLC uses proprietary Linux and there is no SSH access.
Last updated: 2026-08-30
Post by bigwhig on Could not write options file at...
CODESYS Forge
talk
(Post)
Using Codesys 3.5.21.5. Tried installing both by full .exe file and using codesys installer. Installation requires elevation and completes just fine. However when running Codesys and closing the IDE, options-files are not written: Seems regular users are only given read-access to these files: Running Codesys as admin works as admins have full access. Haven’t been necessary before to run as admin. Don’t think I have the issue on my work-laptop, but have experienced this on a number of other computers. Above screenshots are from my private stationary running Windows 11 Pro: Anyone else experiencing this? Is this by design or a known issue?
Last updated: 2026-09-04
Post by harryc on Soft Container License issue with ARM64 Linux
CODESYS Forge
talk
(Post)
Hi, We are working to provide our customers with CODESYS operation on our hardware product ( https://elprotech.com/product/el-qe-e-quantum-edge-series/ ). I'm trying to enable a CODESYS license (Soft container) on our product running ARM64 linux. This problem am having looks similar to here: https://forge.codesys.com/forge/talk/Runtime/thread/6d29b6b4de/ and here: https://forge.codesys.com/forge/talk/Runtime/thread/a2d0c63375/; but I am not running docker, and I am not re-installing a license. This is first time install. I have CODESYS Control SL running on my device, as well as CodeMeter. I purchased a license, and installed it to the CODESYS Development system, (Tools >> License Repository) then tried to install to the device (Tools >> License Manager >> o Device >> o Soft container >> Remote [0001] >> OK. This gives me the "License Manager - Overview" dialog, and the message "Licensing info not available. There is no dongle attached to the device." Below shows the running applications, installed packages, and current content of /var/opt/codesys Also attached screenshots of the Development software as I go through the steps to install the license. # # ps | grep -e "code" -e "CodeMeter" 1391 daemon /usr/sbin/CodeMeterLin 1407 root /opt/codesys/bin/codesyscontrol.bin /etc/codesyscontrol/CODESYSControl.cfg 1442 root /opt/codesysedge/bin/codesysedge.bin /etc/codesysedge/Gateway.cfg 29229 root grep -e code -e CodeMeter # dpkg -l Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Architecture Description +++-==============-=============-============-============================================================================================== ii codemeter-lite 8.20.6539.500 arm64 WIBU CodeMeter minimal runtime ii codesyscontrol 4.14.0.0 arm64 codesyscontrol based on SDK 3.5.20.40 , from Fri Nov 29 08:35:37 CET 2024 [265], Release build ii codesysedge 4.14.0.0 arm64 codesysedge based on SDK 3.5.20.40 , from Fri Nov 29 08:34:19 CET 2024 [265], Release build # ls -la /var/opt/codesys total 208 drwxr-xr-x 6 root root 4096 Nov 7 05:31 . drwxr-xr-x 1 root root 4096 Nov 6 08:33 .. -rw-r--r-- 1 root root 23515 Nov 7 07:26 .Audit.log -rw-r--r-- 1 root root 160 Nov 7 05:31 .GroupDatabase.csv -rw-r--r-- 1 root root 160 Nov 7 04:37 .GroupDatabase.csv_ -rw-r--r-- 1 root root 20736 Nov 29 2024 .SoftContainer_CmRuntime.wbb -rw-r--r-- 1 root root 1982 Nov 29 2024 .UFC_SoftContainer_CmRuntime.WibuCmLif -rw-r--r-- 1 root root 229 Nov 7 04:35 .UserDatabase.csv -rw-r--r-- 1 root root 229 Nov 7 04:35 .UserDatabase.csv_ -rw-r--r-- 1 root root 11807 Nov 7 05:30 .UserMgmtRightsDB.csv drwxr-xr-x 6 root root 4096 Nov 6 08:30 .pki drwxr-xr-x 3 root root 4096 Nov 6 08:30 OPCUAServer drwxr-xr-x 7 root root 4096 Nov 6 08:30 PlcLogic -rw-r--r-- 1 root root 13 Nov 6 08:30 SysFileMap.cfg -rw-r--r-- 1 root root 2640 Nov 29 2024 bacstac.ini drwxr-xr-x 4 root root 4096 Nov 6 08:30 cert -rw-r--r-- 1 root root 94105 Nov 7 07:25 codesyscontrol.log # # uname -a Linux Remote 6.1.22 #5 SMP PREEMPT Tue Nov 18 11:35:46 AEST 2025 aarch64 GNU/Linux #
Last updated: 2025-12-04
Post by reinier-geers on wEBCLIENT Post data api
CODESYS Forge
talk
(Post)
Ive got the webclient axample. If i put https://reversed.notion.site/Marktprijzen-API-89ce600a88ac4abe8c2ad89d3167a83e example to https://reqbin.com/post-online then i get data. If i do the same in Webclient example i get " not a valid graphql request. Why ? sUrl := 'https://graphql.frankenergie.nl/' Request_type_post Contenttype = 1 (json ) Postvalue := '{"query":{"query":"query MarketPrices {\n marketPrices(date:\"2025-12-25\") {\n electricityPrices {\n from\n till\n marketPrice\n marketPriceTax\n sourcingMarkupPrice\n energyTaxPrice\n perUnit\n }\n gasPrices {\n from\n till\n marketPrice\n marketPriceTax\n sourcingMarkupPrice\n energyTaxPrice\n perUnit\n }\n }\n}' I tranfer the postvalue from String to WSTRING
Last updated: 2025-12-25
Post by julianramirez on Visu 4.9.1 auto-logon/login
CODESYS Forge
talk
(Post)
Hello everyone, I have been trying to test the auto-login feature that is advertised on the Release Notes since Visu 4.8: *Version: 4.8.0.0 Besides some bug fixes and improvements this version contains the following new functionality: Alarmmanagement: Possibility to raise alarms programmatically Use real time clock of IEC context Automatic login for WebVisu using Chrome "Sign in automatically"* I am using a personalized login Visualization, the User Management works, however, when ticking the checkbox that keeps the credentials stored, after I reload the page I still see that the user and password details are not filled in. I tried with the default Login Visu (Blue one), and still see the same behavior - VisuUserManagement.VUM_LoginVisualization - I've tried with Chrome and Edge. Thanks for your help
Last updated: 2026-01-12
Post by baotthitawat on Why Structured SCADA Documentation Matters in Modern Industrial Systems
CODESYS Forge
talk
(Post)
Modern SCADA development is no longer limited to monitoring dashboards and PLC communication. Today’s industrial systems often require: Cloud architecture Web & mobile SCADA API integration IIoT communication Alarm management Scalable deployment workflows One challenge in many projects is that deployment knowledge is usually scattered across multiple documents, configuration guides, and troubleshooting references. As systems become more connected, engineers need a more structured learning approach to reduce deployment time and improve maintainability. The ATSCADA Training Book is an interesting example because it organizes the ecosystem into a clearer roadmap covering: SCADA architecture Driver & OPC communication Web visualization Mobile applications Cloud & IIoT systems Troubleshooting & maintenance I think structured technical documentation will become increasingly important as industrial automation systems continue evolving toward larger and more connected environments.
Last updated: 2026-05-27
Post by egerobotics on [New Hardware] EtherCAT Digital & Analog IO Board – CODESYS Compatible, All Channels Isolated
CODESYS Forge
talk
(Post)
Hi everyone, I'd like to share a new EtherCAT slave I/O board I've developed — the EtherCAT Digital & Analog IO Board by EGEROBOTICS. Key specs: 12x isolated digital outputs (24VDC) 12x isolated digital inputs (24VDC) 4x isolated 0–10V analog outputs (12-bit DAC) 4x isolated 0–10V analog inputs (12-bit ADC) All channels galvanically isolated 24VDC powered EtherCAT CoE protocol Typical use cases: Analog servo drive speed reference (0–10V) via EtherCAT Frequency inverter reference signal Proportional valve control Industrial sensor data acquisition Compatible with CODESYS SoftMotion, Beckhoff TwinCAT 2/3, LinuxCNC + EtherCAT HAL, and SOEM. Here's a quick demo video showing it running under CODESYS: 👉 https://www.youtube.com/watch?v=bUuo9reK29s ESI file, PDF manual and AutoCAD drawings available. Available on Tindie: https://www.tindie.com/products/emresensoy/ethercat-digan-io/ Happy to answer any technical questions!
Last updated: 2026-06-13
Post by timvh on CPU + EtherCAT redundancy
CODESYS Forge
talk
(Post)
It works well with two Wago 750-8210's. I helped a few customers setting this up. But it should work with any device which can control EtherCAT I/O, is real-time and has sufficient network interfaces. Two network adapters can be used to create a redundant EtherCAT network (you need 2 additional switches for this). The other network adapters can be used to interconnect the 2 PLC's (synchronization). We noticed that if you exchange variable lists that there could be some issues if you have long lists. So what we did is use a SoftPLC on a server that contains all the settings which continuously sends network packages (GVL sender) and which is received by both PLC's (network receiver). Switching over is done in milliseconds. The bus doesn't notice the change-over. EtherCAT communication works flawlessly.
Last updated: 2026-01-30
Post by steven-schalm on Frustration-Fueled Feedback on Project File Management and Git Integration
CODESYS Forge
talk
(Post)
Yes, it's very tedious, especially since Codesys 4 is a custom web development... At Rex Automatisierungstechnik GmbH, we've invested a lot of time in the Python interface to enable something like CI/CD, but also to export the code and re-import it after making clean modifications. Also, the fact that a class/function block is just a single file containing all the methods, props, etc. Yes, and right now I’m building my own VS Code extension with a clean LSP (Language Server Protocol) for ST, as well as an st-validator, st-formatter, st-linter, codesysPackage.json, and codesys_modules folder... Best regards, Steven Schalm / Sharok6130
Last updated: 2026-06-11
Post by boiwithproblems on branch_copy(checkout=True) liefert ungültigen Projekt-Handle (0) in CODESYS V3.5 SP22 Patch 3
CODESYS Forge
talk
(Post)
Since upgrading from V3.5 SP21 P3 to SP22 P3, this previously working scripted call fails: project, current_branch = project.git.branch_copy(current_branch,new_branch_name,checkout=True) Error: _3S.CoDeSys.Core.Objects.InvalidProjectHandleException Standard Error: The project handle 0 is invalid Workaround: When you do branch copy with checkout=False and then checkout the branch in a seperate line everything works. The issue seems to be that Codesys doesn't give back a proper handle when you do branch_copy with checkout=True. This is mainly so that issue gets noted and resolved in a further Patch and that people with the same issue might have an easier time debugging their scripts. With kind regards Matthias Rudigier
Last updated: 2026-09-22
Post by mankh on Legacy IFM CANopen I/O modules with CR710S / CODESYS 3.5
CODESYS Forge
talk
(Post)
Hi, I am migrating an existing IFM system from CR0020 + CODESYS 2.3 to CR710S + CODESYS 3.5. The existing CANopen I/O modules are: CR9011 CR2042 CR2011 My questions are: Can these legacy IFM CANopen modules be used as slaves with the CR710S CANopen Master? Can their existing EDS files be imported directly into CODESYS 3.5? Are there any known compatibility issues with the old IFM EDS files, PDO mapping, or startup SDO configuration? Has anyone successfully used these modules with a CR710S? If so, could you share the recommended configuration procedure? The goal is to replace the CR0020 with a CR710S while keeping the existing CANopen I/O modules
Last updated: 2026-09-25
Post by gseidel on Mismatch between coordinate monitor and actual motion using SMC_GroupJog2, MC_MoveLinearAbsolute (6DOF)
CODESYS Forge
talk
(Post)
Hi darwin03, as can bee seen at the end of your video, the direction of rotation now seems correct for all axes. I can only guess, but the most likely reason are different denavit hartenberg parameters in the SoftMotion axis group editors and the robot used in the simulation tool. Maybe some arm lengths differ, maybe some offsets are given with opposite sign. I would again refer you to https://content.helpme-codesys.com/en/libs/SM3_Transformation/Current/SM3_Transformation/Function-Blocks/Standalone-Kinematics/Articulated-Robots/6AxisArticulated/Kin_ArticulatedRobot_6DOF.html. Please double check all parameters and the table of the DH parameters given there and compare that against the robot in the simulation tool. Also: did you configure any tool in CODESYS? I would suggest to simplify and remove any tools for finding the source of the wrong movements. Best regards, Georg
Last updated: 2026-10-16
Post by martinlithlith on CODESYS Control for Raspberry Pi SL on Raspberry Pi 4b
CODESYS Forge
talk
(Post)
hi! a quick question - is it possible to run CODESYS Control for Raspberry Pi SL license on a raspberry pi 4b? i know it says all models in the data sheet, but im not sure it the data sheet has been updated seince the MC-processors for pi. best, Martin
Last updated: 2023-09-04
Post by transmin01 on EL6751 Canopen_Manager issue
CODESYS Forge
talk
(Post)
Hi, I have a Beckhoff EL6751 EtherCAT / CANopen gateway which fails on the Canbus when the CANopen_Manager is added. Currently no devices are connected to the EL6751. If I add a device, I get the same issue. If I add a device and connect the bus, I get the same issue. Is there something I am doing wrong? Regards Trevor
Last updated: 2023-09-12
Post by snhatton on Alarm Management - latched variable represented as Text list
CODESYS Forge
talk
(Post)
Hi There, For my understanding: are you trying to display the contents of a text list in an alarm message based on the id? For example, you could maintain a text list of common alarm messages, and then display based on which message is true?
Last updated: 2023-09-18
Post by derpaul on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED
CODESYS Forge
talk
(Post)
I've post the Versions in the Attachments. It seems with htop, that there is a very high CPU Load. In the Log I can see nothing, as mentioned above I've to restart the PLC with Power off/on and the log in codesys was deleted. Or what do you mean with plclogger?
Last updated: 2023-09-23
Post by i-campbell on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED
CODESYS Forge
talk
(Post)
I can't answer why it's not resetting, but from the description of g_udiMaxReceiveBufferSize, I would guess the sum of sizes of the mqtt packets received in one cycle exceeded this value. So the answer may be to increase that parameter. https://content.helpme-codesys.com/en/libs/MQTT%20Client%20SL/Current/MQTT-Client/Common/Params/MQTTParam.html https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_dlg_library_parameter.html
Last updated: 2023-09-26
Post by sivakov on CoDeSys Exception EIP Adapter
CODESYS Forge
talk
(Post)
Hi, Got same problem, appeared after 4.3.1.0 update. Prabably problem is in performance. I am using virtual machine, so adding one more core and several GB to RAM still not solved, but atleast did system more stable. Try optimise your main program or set less task interval. Regards, I will be your mate in solving this mistery =)
Last updated: 2023-09-28
Post by chiali on Recipe issue.
CODESYS Forge
talk
(Post)
Hi Everyone, I'm trying to make a simple Recipe project using 'Save Recipe In File' and 'Load and Write Recipe' Execute Command buttons in Visualization but No dialog box 'Save As' appears when I click on buttons (Nothing happens). What is wrong. Please see the attached files. Best Regards, Chiali.
Last updated: 2023-10-23
Post by andrax on Mux I2C
CODESYS Forge
talk
(Post)
Hi, sorry I was not there for a long time. The TCA9548 needs terminating resistors, do you have them in? That's why I went to QWIIC, the muxboard already has them built in. If it still does not work, try it first without the muxboard. PS: Note the channel assignment. Muxboard 0 = I2C_Master 1,0,0,0,0,0,0,0 Muxboard 1 = I2C_Master 2,0,0,0,0,0,0,0 etc.
Last updated: 2023-10-29
Post by leon78 on Codesys 3.5 SP17 Patch 2 CheckBounds (POUs for Implicit Checks)
CODESYS Forge
talk
(Post)
Hello! I use CheckBounds (POUs for Implicit Checks). But I have a problem. I use an array as an VAR_IN_OUT of Function Block. If I try to monitor the array of variable length ([* ]), its does't work. The CheckBounds POU isn't called. If I use the array of fixed lenght ([lower..upper]), the CheckBounds POU is called. Why?
Last updated: 2023-11-14
Post by leon78 on Codesys 3.5 SP17 Patch 2 CheckBounds (POUs for Implicit Checks)
CODESYS Forge
talk
(Post)
Hello! I use CheckBounds (POUs for Implicit Checks). But I have a problem. I use an array as an VAR_IN_OUT of Function Block. If I try to monitor the array of variable length ([* ]), its does't work. The CheckBounds POU isn't called. If I use the array of fixed lenght ([lower..upper]), the CheckBounds POU is called. Why?
Last updated: 2023-11-14
To search for an exact phrase, put it in quotes. Example: "getting started docs"
To exclude a word or phrase, put a dash in front of it. Example: docs -help
To search on specific fields, use these field names instead of a general text search. You can group with AND or OR.