Post by transmin01 on PCAN serial "No CAN driver found" ^{CODESYS Forge talk (Post)}
Hi, I am using a PCAN mini CAN board which has the Windows drivers installed on the target PLC. PCAN board can be seen in device manager. However, I am getting "No CAN driver found" error. I have read the post https://forge.codesys.com/forge/talk/CODESYS-V2/thread/44aae19318/ and have uncommented the CmpPCANBasicDrv driver in the CodesysControl.cfg file in development PC and have copied it to the target PC. Current CodesysControl.cfg file attached. Is there anything else I am missing? Regards
Last updated: 2023-09-14

Post by timvh on When Keyboard Key is in Hold, then Webvisu is extreme slow and latent ^{CODESYS Forge talk (Post)}
I'm not really sure what you are trying to do, but maybe you are referring to using the CmpCharDevice library? When you "open" the connection to a device, you can pass flags. What helped me is to set the non-blocking flag. I'm not sure if this is what you are referring to, but maybe it helps: dFlags: DINT := CmpCharDevice.ACCESS_MODE.O_RDONLY + DINT#4000; // see details for flags: http://linux.die.net/man/2/open, + DINT#4000 is for non-blocking hDevice := CmpCharDevice.CDOpen(szFilename, dFlags, Result);
Last updated: 2023-09-20

Post by nathant on Can't open online view of FB instance from code editor, only from Device/POU windows ^{CODESYS Forge talk (Post)}
Hello, The title pretty much says it all. When trying to open a FB from the CFC/Ladder/SFC editors while online, the FB does not open in an online view of that specific instance. Instead, it opens an offline view with '???' shown for the value of any variable. This makes debugging extremely cumbersome, as I have to find each FB in the POU window and select the specific instance I am trying to view. Anyone know the cause/solution for this? Thanks.
Last updated: 2023-11-08

Post by fred on Rasperry Control Debian 12 ^{CODESYS Forge talk (Post)}
Hi, I have Proxmox running on a Rasperry 4 and have debian 12 ARM installed here. I wanted to install Codesys Control for Raspberry on it. According to the messages, the runtime environment and the gateway were installed successfully, but I can't find a device to downplay a program. The sudo service codesys start command fails. (see image) Does somebody has any idea? Thank you for your help! Greetings Fred
Last updated: 2023-11-22

Post by siggi95 on Übersetzungsfehler J1939 changeAdress (4.1.0.0) ^{CODESYS Forge talk (Post)}
Hallo zusammen, für den Aufruf VAR deviceDiag: J1939.IJ1939LocalECU; END_VAR deviceDiag.ChangeAddress(5); gibt es mit der Version 4.1.0.0 der Lib IoDrvJ1939 Übersetzungsfehler - C0035: Programmname, Funktion oder Funktionsbausteinstanz an Stelle von 'deviceDiag.ChangeAddress' erwartet - C0004: 'ChangeAddress' ist keine Komponente von 'IJ1939LocalECU__Union' Mit der bisher verwendeten Lib-version 3.5.17.0 nicht und auch das Setzen der device adress hat funktioniert. Lt. Release notes ("J1939: ChangeAddress method does not work properly.") wurde hier verbessert. Leider habe ich keine Beschbreibung dazu gefunden. Wie muss der Aufruf angepasst werden? Vieeln Dank und beste Grüße Siggi
Last updated: 2023-11-29

Post by snhatton on Running webvisu with Codesys Control Win V3 in Simulation Mode ^{CODESYS Forge talk (Post)}
Yes, you can use the CODESYS ControlWin V3 Soft PLC. However, if simulation is enabled on the device this will disable all communication, so you need to turn off simulation to view the visualization in a web browser. In simulation mode, all IO and communication is disabled for standalone testing. In addition, make sure to set the start visualization in the WebVisu object in the application tree. I hope this helps!
Last updated: 2023-12-04

Post by mg0815 on Codesys Control log "eventbuffer full" ^{CODESYS Forge talk (Post)}
Device: RPI 3b or 3B+ System: Wheezy Codesys: 3.5.16.2 I got the Log: 2023-12-13T00:38:43Z, 0x00000054, 2,6,11, !!!! Warning: Eventbuffer full for app=<app>Application</app>; an inputevent with the tag <tag>128</tag> has been dropped This log happens aroud 10 times a second. Sometimes the controller stopped working any more. What is the reason for this? I will update this controller soon (I hope so, but in the meantime I should at least know hoe to prevent this issue) Mario
Last updated: 2023-12-14

Post by elektron785 on CAN-Bus in Demo-Version ^{CODESYS Forge talk (Post)}
Hallo, wie verhält es sich mit der Demo-Version und Datenübertragung z.B. via CAN-Bus. Der Bus läuft, das Device befindet sich im Zustand "Operational" aber es werden keine Daten von der Soft-SPS empfangen. Ich benutze aktuell eine nicht lizenzierte Version von CoDeSys Control for Linux ARM64SL. Normalerweise sollte die Demo-Version uneingeschränkt laufen - also kann ich davon ausgehen, dass es sich um einen Programmierfehler handelt oder ist die Feldbusfunktion ohne Lizenz doch in irgendeiner Form eingeschränkt verfügbar (außer dem 30 Minuten Limit nach Reboot)?
Last updated: 2024-02-06

Post by timl on BacNet Server ^{CODESYS Forge talk (Post)}
Hallo, für einen BacNet2 Server lassen sich mit zwei Ethernet Schnittstellen auch zwei Bacnet 2 IP Datalinks anlegen. Einen Datalink nutze ich für den UDP Port 47808 und einen für den UDP Port 47809. Dadurch ist der Server aus beiden Netzwerken erreichbar, was so gewollt ist. Allerdings verbindet er die beiden Netze auch miteinander, was zu Kommunikationsproblemen führt, da in beiden Netzwerken bereits gleiche Device ID's vergeben sind und diese sich dann doppeln. Lässt sich diese Verbindung der beiden Netze abschalten? Gruß Tim
Last updated: 2024-02-20

Post by mimodia1 on I do not have any reedings in RUN MODE from MPU6050........ ^{CODESYS Forge talk (Post)}
Good morning, mecke96. Exactly the same thing happens to me, although I have not done the part of executing a .py file. It only reads the temperature and the counter, but the other values are zero as in your image "no readings". I have tested the MPU6050 device on an Arduino and it works. Could you tell me if you solved it?
Last updated: 2024-03-29

Post by ofey on EtherCAT fieldbus ^{CODESYS Forge talk (Post)}
Okey, thank you! Do you think it is something in this library, that makes it possible to do the configuration in a PRG? https://content.helpme-codesys.com/en/libs/IODrvEtherCATDriver/Current/IoDrvEtherCAT.html#id1 I think the codesys modbus libraries support configuration and connection to modbus slaves without having to add the slave devices in the device tree. Just do it from function blocks inside the program. I was hoping for something similar with EtherCAT.
Last updated: 2024-04-10

Post by valenting on Problem with Licenced Software Metrics ^{CODESYS Forge talk (Post)}
Hi, When I try to install my codesys program with the new application-based licensing, I have an error "it exceeds the scope of the license agreement. See Device > Licensed Software Metrics" In the Licensed Software Metrics section, I see a code size < 3MB and less than 2700 variables in visualiaztions. I'm using a license "Control Basic L" with "Codesys Visualization L" option, so it should be enough with these metrics. What can I do ?
Last updated: 2024-04-22

Post by valenting on Problem with Licenced Software Metrics ^{CODESYS Forge talk (Post)}
Hi, I tried with another project, using codesys SP20 with the latest visualization installed, I can install the application on my device but it doesn't work I get an exception "invalid license metrics" and the app won't run See attached the metrics in project and allowed by license, and the logs What am I supposed to do ? Everything is in the newest version and the values are lower than allowed and nothing works...
Last updated: 2024-04-26

Post by yannick on Raspberry PI 5 not working ^{CODESYS Forge talk (Post)}
Hello I'm using Codesys V3.5 SP19 Patch 6 and a Raspberry PI 5 4GB Bookworm 32bit with the Runtime 4.11.0.0 SL. I can install the runtime and download the software completly but after a few seconds the connection disconnects with the message no connection to device. Please scan network again. And the object reference was not set to an object instance. See screenshot. Can somebody help me with that? Thanks
Last updated: 2024-04-28

Post by miodusy on CODESYS Control Standard S and Beaglebone ^{CODESYS Forge talk (Post)}
Hi, CODESYS Control Standard S + CODESYS Visualization L, CODESYS Control for Beaglebone 4.11.0.0, CODESYS V3.5 SP20 + (64-bit) I have problem that license manager say that this device is not supported when i try active whole license. When I select only runtime and communication it is go next step, but then I no have license on in Visualistion section, all of rest of software metric licese is ok(IO, Istances of com et, code size etc.). Thanks!
Last updated: 2024-05-11

Post by engrahman on The current baud rate could not be determined in CR0020 IFM with maintenance tool ^{CODESYS Forge talk (Post)}
Hello everyone, im working with IFM CR0020 controller via RS232 protocol where im trying to connect it to my PC but, every time when im using the maintenance tool to identify the device i get the error "The baud rate could not be determined" i have tried to change the cable of RS232 with different types but the error presist, any idea how to fix it
Last updated: 2024-05-21

Post by yofi on Raspberry Pi 4 POU not running ^{CODESYS Forge talk (Post)}
I have this error where the pou doesn't run even for simple programs like contact and a coil if i remove the pou from the task and put another one it works for one run then it stops working again in the photo we can see a contact is on but the coil connected to it is still not on and the device is in run mode I had this issue again and again any help
Last updated: 2024-06-02

Post by yofi on Raspberry Pi 4 POU not running ^{CODESYS Forge talk (Post)}
I have this error where the pou doesn't run even for simple programs like contact and a coil if i remove the pou from the task and put another one it works for one run then it stops working again in the photo we can see a contact is on but the coil connected to it is still not on and the device is in run mode I had this issue again and again any help
Last updated: 2024-06-02

Post by kris-samoy on Get Alarm status in Codesys ^{CODESYS Forge talk (Post)}
I am rather new to Codesys and I'm trying to figure out how to get the status of an alarm. This to interlock the start of a device until the alarm has been acknowledged... I am not sure if IAlarm.GetState (METH) can be used for this purpose. If yes then could someone please briefly explain how to use this? https://content.helpme-codesys.com/en/libs/AlarmManager/4.1.0.0/Interfaces/pou-IAlarm/GetState.html Thx & grtz, Kris
Last updated: 2024-06-03

Post by mozed on Bug Device login ^{CODESYS Forge talk (Post)}
Good morning, The problem I encounter is very disturbing, when I try to connect to my project, it asks me to put in my username and password, which I do. However, I cannot connect and it restarts. the window to rewrite my identifiers. However it is the correct identifier and password I do not understand why. When I try to put false identifiers there strangely it tells me that these are not valid identifiers. There is something what can I do? Sincerely
Last updated: 2024-06-11

Post by srouse on PFC200BUS not running ^{CODESYS Forge talk (Post)}
I started a project in codesys for a WAGO 750-8212 PLC and I am working on getting online with the controller. I can log in to the controller and I can see and control all of the fieldbus couplers that I have. I am unable to get the internal bus working. It just says that the bus is not running and when I scan or devices nothing shows up. Am I missing something important in my device tree?
Last updated: 2024-07-10

Post by dantheman on Connecting to SoftPLC Only Works By Turning Off Modbus Ethernet Port ^{CODESYS Forge talk (Post)}
I have an IPC with 2 ethernet ports and 1 Wi-Fi. I'm using ModbusTCP with the ethernet port named "enp2s0" connected to my remote I/O. This works fine when testing with Python and also works with CODESYS, but CODESYS is only able to scan for the Linux SoftPLC when I turn off the "enp2s0" interface. In other words, I can't get online with the IDE if I want my ModbusTCP comms to run with CODESYS. I'm using a Linux SoftPLC that has the following entry in CODESYSControl.cfg, hoping that this will allow me to connect with "enp1s0" or "wlp3s0", and leave "enp2s0" for field comms, but this seems to only make the source IP of the ModbusTCP comms to be bound to "enp2s0". That last point is the case only if I don't restart the service, but if I do restart the service after changing the config file, the source IP for the ModbusTCP comms then becomes the one for "enp1s0", which is very confusing to me: [SysSocket] Adapter.0.Name="enp2s0" Adapter.0.EnableSetIpAndMask=1 On the device list, I only have "enp2s0" given as the ethernet device that has the ModbusTCP master & slave beneath it, shown in Screenshot 1. On the IPC, I can ping the ModbusTCP client (remote I/O) from "enp2s0", and I've attached a Wireshark capture of running ModbusTCP from the CODESYS runtime as Screenshot 2, 3 & 4 (again, I can't get online when this is running, I have to turn off "enp2s0" to connect even when it's idle and I don't have an active TCP session with my Python tests). Like I explained above, the source IP is "enp1s0", even though the ethernet device on the project is "enp2s0". I was lucky to catch the red message that showed the source IP that makes sense to me (the one for "enp2s0"), but for some reason that connection was reset and I never saw that packet again. I've also tried this with Auto-reconnect both enabled & disabled, for the ModbusTCP Master device. I also have to turn off "enp1s0" and then turn it on, just so that I can have the ModbusTCP comms running from "enp2s0" (which is not intuitive in any way to me, I'd love some help understanding that phenomenon as well) in the weird manner that I've described above. I would be very appreciative if someone can help me figure out this pickle. I'd love to just connect to CODESYS through my Wi-Fi interface and leave my ethernet ports for field comms.
Last updated: 2024-08-01

Post by nicopolux on Profinet RPC-call error ^{CODESYS Forge talk (Post)}
Hello everyone Since I have installed Codesys 3.5.20sp2 I cannot get the profinet features working again. Now I get RPC Blocked during device scan (see attached file) and when online I get RPC-call error (see attached file). I run Codesys on the last version of Windows 11, Profinet ports have been added to Firewall rules, and even with disabled Firewall I get same result I really never seen that before Same result using another PC I already spent 2 days to find the issu without any success, I would appreciate some help, thank you! Nico
Last updated: 2024-08-22

Post by timvh on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
If your Control Win is the Modbus "Master" then your configuration should be something like: Modbus_COM (Serial port) - Modbus Master (this is the Control Win SoftPLC actively setting up the communication) - Modbus Slave (this is then your WAGO 750-315) You need to add channels to the Modbus Slave configuration to inform the master which variables to read/write from the Wago module. The way you configured it now, the Control Win is also a slave. PS, don't forget to put the PLC (Control Win) in Run.
Last updated: 2024-09-03

Post by trprsmn on "Scan Network" doesn't find CR1140 device (ifm) ^{CODESYS Forge talk (Post)}
Hi, I'm watching an ifm tutorial on how to setup an industrial controller in CODESYS. I'm using an 'ecomatDisplay43inch_64bit) controller. CODESYS Gateway and PLC are both runngin (systray). However if I click "Scan Network" I can't find my controller. The only thing it finds is a "desktop" it seems (I'm using a Windows 10 on a Mac Book using VMWare, so maybe it has something to do with that?). How can I fix this? Thanks in advance!
Last updated: 2024-09-11

Sort by relevance or date