Post by dkugler on Beckhoff EL6652-0010 with Codesys ^{CODESYS Forge talk (Post)}
we use successful for many years the KEB MFI terminal for Profinet, EtherCAT, Ethernet/IP,... You'll need a EtherCAT Coupler as "head" from KEB, Kendrion or Berghof. It's all the same board inside: https://www.kebamerica.com/products/ethercat-bus-coupler/ Or the coupler with 16Di/Do integrated: https://www.kebamerica.com/products/ethercat-digital-io-module/ last year I got a EK1100 with EL6731 Profibus treminal runnig. But it was a lot of reverse engineering and thinkering in Codesys and TwinCAT to be done, to get it up, fulfilling my needs. Good luck!
Last updated: 2025-03-25

Post by janderson on Ethercat scan for devices not picking up EL7041 as a softmotion axis ^{CODESYS Forge talk (Post)}
I have a beckhoff EL7041-1000 rev 21 in my ethercat bus but it wont correctly create a softmotion axis unless i manually insert the device. scan for devices gives me an el7041-1000 without an SM3 axis.
Last updated: 2023-09-02

Post by trycyclepower on EtherCAT drive going into fault mode require power cycle everytime ^{CODESYS Forge talk (Post)}
I have EtherCAT servo drive lost communication with PLC everytime it gets faulted, it does not not communicate until I power cycle everything again, how to solve this issue?
Last updated: 2024-09-11

Post by reinier-geers on Ethercat not running. ^{CODESYS Forge talk (Post)}
I change a running programm but now ethercat is not running. all users are there. Why is it always problems with codesys/ Diadesigner. i see also a Crist ? Why ther is only one master
Last updated: 2024-10-16

Post by kbucsit22 on Ethercat Slave - Load PDO From Device ^{CODESYS Forge talk (Post)}
Hi All, I am using Control Win V3 x64. Anyone experiences to use Expert mode to map the Ethercat Slave device to press this Load PDO from Device, Pressed first time then nothing happens. Pressed second time then the software crashes. Best regards, Kenneth
Last updated: 2024-10-22

Post by kbucsit22 on Ethercat Slave - Load PDO From Device ^{CODESYS Forge talk (Post)}
Codesys Version V3.5 SP20 Patch 3 Ethercat Master: EXW1-BECAC (SMC) The Load PDO Button was pressed but software hangs. I try Beckhoff its working, dont know Codesys got issues.
Last updated: 2024-10-25

Post by kbucsit22 on Ethercat Slave - Load PDO From Device ^{CODESYS Forge talk (Post)}
Codesys Version V3.5 SP20 Patch 3 Ethercat Master: EXW1-BECAC (SMC) The Load PDO Button was pressed but software hangs. I try Beckhoff its working, dont know Codesys got issues.
Last updated: 2024-10-25

Post by andrax on Ethercat auf Raspbery 4 ^{CODESYS Forge talk (Post)}
Hallo zusammen, ich prüfe gerade eine Machbarkeit. Bei Ethercat werden ja bestimmte Anforderungen an die Netzwerkkarte gestellt. Wie sieht es da beim Raspbery 4 aus? Wird es funktionieren und was ist zu beachten? Grüße
Last updated: 2024-11-22

Post by ph0010421 on Axis EtherCAT address ^{CODESYS Forge talk (Post)}
Hello SDO will write to the drive, not the axis, so you need to pass in the ethercat slave: VAR_IN_OUT Axis: IoDrvEthercatLib.ETCSlave; END_VAR Then you can get the address with: Axis.PhysSlaveAddr (as UINT)
Last updated: 2025-03-07

Post by eschwellinger on ETHERCAT EK1100 und EL8601-8411 ^{CODESYS Forge talk (Post)}
welche Ethercat Masterversion verwendest du? Wenn nicht die aktuelle - bitte mit dem CODESYS Installer aktualisieren.(falls du ne alte Version hattest auch bitte nomal die ESI neuinstallieren + Gerätscannen)
Last updated: 2025-04-09

Post by ahofer on ETHERCAT EK1100 und EL8601-8411 ^{CODESYS Forge talk (Post)}
Leider etwas verspätet erst mal danke für die Antwort und für die Info. Ich habe jetzt ein Upate vom EtherCAT Master gemacht. Die Klemme funktioniert in ihrer Standardeinstellung. Bei den PWM-Klemmen geht das Umstellen auf DO, aber den Zähler kann ich immer noch nicht einstecken.
Last updated: 2025-05-21

Post by gseidel on SMC_FB_WASNT_CALLED_DURING_MOTION when enable MC_MoveRelative ^{CODESYS Forge talk (Post)}
Hi ducng, please make sure to call all Motion-FBs in the EtherCAT task. In your case, the PLC_PRG should be below the EtherCAT task, not the MainTask. Best regards, Georg
Last updated: 2025-11-03

Post by eschwellinger on EtherCAT status errors ^{CODESYS Forge talk (Post)}
Setting IRQ priorities using shell commands irq-list and irq-set-prio for the network adapter which is used for Ethercat. This is here: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_performance_optimization_linux.html
Last updated: 2025-11-25

Post by anhkdv on Motion FB Error ^{CODESYS Forge talk (Post)}
Hi! I'm a newbie. I'm doing a project for Delta Robot using Codesys and got this error when trying to move in a dynamic coordinate system. This error occurs when I use FB MC_MoveLinearRelative and FB SMC_GroupWait
Last updated: 2023-10-08

Post by ragarcia on Error while using UpdateConfiguredIPSettings to change IP address ^{CODESYS Forge talk (Post)}
I did check I cannot see any error log. It is when executing the Reconfigure function that I get an error as return from that function.
Last updated: 2024-02-19

Post by chir on SMC_REGULATOR_OR_START_NOT_SET issue ^{CODESYS Forge talk (Post)}
Hello everyone! I faced the error SMC_REGULATOR_OR_START_NOT_SET using InoProShop (Inovance IDE). This error occured then I enable MC_Power block. The output BUSY is TRUE constantly.. The description of this error in documentation - "Controller enable not done or brake applied". Maybe someone know how to solve this problem
Last updated: 2024-04-19

Post by donm on Regarding trend storage access error ^{CODESYS Forge talk (Post)}
i have created a project which contain 30 trend and suddenly trend recording is not working. its showing an error 30437."Determination of root pages for recording did not work for 'screen', error:30437" how to solve this issue?
Last updated: 2024-05-27

Post by donm on trend storage access error ^{CODESYS Forge talk (Post)}
i have created a project which contain 30 trend and suddenly trend recording is not working. its showing an error 30437."Determination of root pages for recording did not work for 'screen', error:30437" how to solve this issue?
Last updated: 2024-05-27

Post by fahrettin on CODESYS 3.5.17.30 Setup Error ^{CODESYS Forge talk (Post)}
While trying to install CODESYS 3.5.17.30 (64-bit) on my Windows 11 computer, I'm getting the errors below. The first error occurs near the end of the installation. Once you bypass it, the installation returns the second error. Do you have any suggestions for a solution? By the way, I've tried this on several PCs, but I haven't found a solution.
Last updated: 2025-10-30

an error happened; will automatically restart -vermeidbar? ^{CODESYS Forge talk (Thread)}
an error happened; will automatically restart -vermeidbar?
Last updated: 2015-05-31

CODESYS Automation Server Connector [1.12.0.0] Installation Error ^{CODESYS Forge talk (Thread)}
CODESYS Automation Server Connector [1.12.0.0] Installation Error
Last updated: 2020-09-12

Error IoDrvEthernetIP: Connection Failure. (16#1) How to solve ^{CODESYS Forge talk (Thread)}
Error IoDrvEthernetIP: Connection Failure. (16#1) How to solve
Last updated: 2024-07-22

Connection error to Wago 750-363 EtherNet/IP Adapter ^{CODESYS Forge talk (Thread)}
Connection error to Wago 750-363 EtherNet/IP Adapter
Last updated: 2024-07-22

False Notification Application Error with raspberry pi 4 ^{CODESYS Forge talk (Thread)}
False Notification Application Error with raspberry pi 4
Last updated: 2024-09-03

ERROR: CodeMAccess2: Used CmRuntime 2.61.2705.500 is too old ^{CODESYS Forge talk (Thread)}
ERROR: CodeMAccess2: Used CmRuntime 2.61.2705.500 is too old
Last updated: 2024-09-18

Sort by relevance or date