Post by wind-11 on Problem with simulation Modbus ^{CODESYS Forge talk (Post)}
Hello everyone, I encountered a problem in the simulation while working. In a test project we set up a Modbus connection. We wanted to simulate this with test values. The connection also worked, but unfortunately the values are frozen and do not report any “current data”. (Picture attached) Since these are my first points of contact with Codesys and my colleague continues to work elsewhere, I was hoping that someone here might have an idea. Kind regards and thanks in advance.
Last updated: 2024-03-22

Post by mbmik on IoDrvModbusTCP_Diag not defined when using MODBUS ^{CODESYS Forge talk (Post)}
Hi Im trying to setup a Weidmüller WL2000 to run with MODBUS, to get some data from a server. Codesys V3.5 SP20. The issue is, that whenever i attach an ethernet port and add MODBUS Master und also a Slave, codesys will compile the project, but there always seem to be some remaining errors, which or only visible, when setting the messages window to "Pre-Compiled". I tried a lot of stuff to get rid of these errors, but cant find to seem the reason. New installation of codesys, cleaned project, setup completely empty new project, manually adding libs. Nothing helps. Any help is apreciated. Maybe we are doing something wrong.. Example Project is available, if somebodey wants to take a look. Greetings and thanks alot
Last updated: 2024-04-15

Post by schorge on Modbus RTU Slave ^{CODESYS Forge talk (Post)}
Ich würde gerne bestimmt Modbus RTU Slave Adressen auslesen, leider bekomme ich keine Werte vom Bus. Verbindung erfolgt über einen Raspberry mit Modbus RS485 Adapter, welcher erfolgreich verbunden ist. Mit einem IOBroker kann ich die Daten erfolgreich auslesen. In der Modbus_COM_Port => Modbus_Serial_Device habe ich Input Register 4000 %QW und Startadressen auf Input Register 3000, als Variable ein Array[0..2999] of Word, kann aber keine Werte auslesen.
Last updated: 2023-12-06

Post by dengsberg on Disable Communications to 'Modbus_Server_COM_Port' from the logic ^{CODESYS Forge talk (Post)}
I have a serial Modbus RTU communicating to the Slave device. But when the control system is not in Run there is no power applied to one of the Modbus Devices. Can I enable / disable the communications to that Modbus Slave in the code based on my running mode, so I don't get all the errors?
Last updated: 2024-08-29

Post by bolopg on MODBUS TCP REGISTERS CODESYS V3.5 ^{CODESYS Forge talk (Post)}
Hi. I have a problem with MODBUS TCP MASTER. I treid to read HR in range 3027-3037 but I cannot read them. I have modbus slave chanel with offset 0x3037. I checked what I read and it looks like I am reading HR in range 1-10. What I am doing wrong.
Last updated: 2024-10-11

Post by ahuckphin on Issues with Modbus Slave with Raspberry Pi ^{CODESYS Forge talk (Post)}
I have a DFRobot RS485 temperature & humidity sensor (SEN0438) connected to my Raspberry Pi via a USB to RS485 adapter. I am able to connect and read the sensor data when running a python code locally. However in Codesys, I encounter this error "A bus error has occurred." and "There was no response in time". Could this be because of Modbus Server Channel and Modbus Server Init configuration on my part? Admittedly I am new to Codesys. To get to this stage, I: 1. added some lines to CODESYSControl_User.cfg 2. added "Modbus_COM" in Codesys and set "Serial Port Configuration" under "General" 3. added "Modbus_Master_COM_Port" in Codesys and checked transmission mode is set to "RTU" 4. added "Modbus_Slave_COM_Port" in Codesys and checked server address is set to 1 (also set 1 in my sensor) 5. added 1 channel and 1 init for "Modbus_Slave_COM_Port" under "Modbus Server Channel" and "Modbus Server Init"
Last updated: 2024-07-10

Post by timvh on Accessing ModbusTCP addresses from python ^{CODESYS Forge talk (Post)}
https://en.wikipedia.org/wiki/Modbus
Last updated: 2023-09-20

Post by eschwellinger on IoDrvModbusTCP_Diag not defined when using MODBUS ^{CODESYS Forge talk (Post)}
known issue hopefully solved to next version
Last updated: 2024-04-18

Post by ahuckphin on Issues with Modbus Slave with Raspberry Pi ^{CODESYS Forge talk (Post)}
duplicate
Last updated: 2024-07-11

Post by dohy on Modbus RTU Response CRC fail ^{CODESYS Forge talk (Post)}
Did you resolve it?
Last updated: 2024-09-19

Post by ph0010421 on MODBUS TCP REGISTERS CODESYS V3.5 ^{CODESYS Forge talk (Post)}
hello Use FC3 instead of FC4
Last updated: 2024-10-11

Post by bartspako on Connection between Beijer PLC and Schneider Tesys-Island using Modbus TCP ^{CODESYS Forge talk (Post)}
Last updated: 2024-10-16

Post by sumit on Not able to see input data coming from eip adapter on codesys ^{CODESYS Forge talk (Post)}
Hello there, I have an eip adapter running (remotely) that is sending data back to eip scanner (running on codesys). I can send data from scanner (codesys) to the adapter but not getting the data back from the adapter. I have verified the incoming data on wireshark but I don't see this data in the codesys. I have tried local variable mapping and global variable mapping not variable values just stays at 0. Please guide.
Last updated: 2024-02-29

Hi, I try to send and receive data using a UDP connection via SysSocket 3.5.17.0. While sending data works fine, I have problems with the receiving part. I am able to capture the received data of client side in wireshark But unable to capture it on the codesys ^{CODESYS Forge talk (Thread)}
Hi, I try to send and receive data using a UDP connection via SysSocket 3.5.17.0. While sending data works fine, I have problems with the receiving part. I am able to capture the received data of client side in wireshark But unable to capture it on the codesys
Last updated: 2024-06-03

Post by paulorb on STRUCT AT %MW1000 ^{CODESYS Forge talk (Post)}
Hi I am trying to use STRUCT to parse commands from Modbus/TCP, Modbus client will fill the bytes related to a specific command (type, parameters), then PLC (Codesys) will access the command parameters. A STRUCT will simplify a lot the process of parsing the data, so I don't need to parse byte per byte, address will be mapped to a struct and I can use it for parsing the data. From what I understood, the compiler does not allow me to specify the location of the struct for a %MW register. VAR_COMMAND AT %MW1002: structGenericModbusCommand; This will throw: Bad declaration, use '%ML' for 'structGenericModbusCommand' variable But If I change it to %ML, when you go online you see that it is actually allocating the struct in another memory address. When we go online, on GVL we can see: VAR_COMMAND. structGenericModbusCommand %ML1002 commandType COMMANDTYPE %MB8016 ... %MB8020 I am not specifying a pointer or a reference it is a struct type, why is it mapping to a %MW location (random one). How can I control where it is mapping to? I need a consistent way to map STRUCT to specific modbus address. Is it possible? Thanks, Paulo Note I am using a Codesys OEM: Schneider Machine Expert Logic Builder (M241)
Last updated: 2024-08-13

Post by laazik2 on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
I am actually wondering as well if there are plans to fix it or not? As adding two modbus devices creates it's own problems with connection limits and other issues, which some slave devices have.
Last updated: 2023-09-05

How to use more 4 instances of CANopen/Profibus/Modbus with The application-based license CODESYS Control ^{CODESYS Forge talk (Thread)}
How to use more 4 instances of CANopen/Profibus/Modbus with The application-based license CODESYS Control
Last updated: 2023-11-02

Post by gorditron on Modbus Slave RTU in der Applikation abschalten ^{CODESYS Forge talk (Post)}
Hallo, gibt es eine Möglichkeit die Modbus Slaves (ModbusSlaveComPort) innerhalb der Applikation über ein Variable zu aktivieren oder zu deaktivieren? Bilder als Datei Danke!
Last updated: 2023-11-09

Controlling PM564-eth PLC using Weintek HMI with MODBUS TCP/I. I keep getting communication errors. ^{CODESYS Forge talk (Thread)}
Controlling PM564-eth PLC using Weintek HMI with MODBUS TCP/I. I keep getting communication errors.
Last updated: 2021-02-15

Post by squiggleypuff on Can't Add New Version of Modbus TCP Master ^{CODESYS Forge talk (Post)}
Turns out Modbus was working despite the pre-compiler errors; I was reading the wrong addresses of the slave device, which was why I was seeing all 0s. Thanks for ignoring me.
Last updated: 2024-04-09

Post by brzozka100 on Change modbus server parameters from program ^{CODESYS Forge talk (Post)}
Hello, is there a possibility to change modbus server parameters (baud rate, parity, etc.) configured in devices tree from PRG? I need to be able to change them, for example, from HMI.
Last updated: 2024-07-16

Post by brzozka100 on Change modbus server parameters from program ^{CODESYS Forge talk (Post)}
Hello, is there a possibility to change modbus server parameters (baud rate, parity, etc.) configured in devices tree from PRG? I need to be able to change them, for example, from HMI.
Last updated: 2024-07-16

Post by wagomikep on Number of Connections to Modbus TCP Slave ^{CODESYS Forge talk (Post)}
Hello, Is there a maximum number of Masters that can connect to a Modbus Slave that is configured in the device tree? Is this limited by the CODESYS IDE, or the manufactures hardware and CPU load? Thank you,
Last updated: 2024-08-01

Post by wagomikep on Number of Connections to Modbus TCP Slave ^{CODESYS Forge talk (Post)}
Hello, Is there a maximum number of Masters that can connect to a Modbus Slave that is configured in the device tree? Is this limited by the CODESYS IDE, or the manufactures hardware and CPU load? Thank you,
Last updated: 2024-08-01

Post by wagomikep on Number of Connections to Modbus TCP Slave ^{CODESYS Forge talk (Post)}
Hello, Is there a maximum number of Masters that can connect to a Modbus Slave that is configured in the device tree? Is this limited by the CODESYS IDE, or the manufactures hardware and CPU load? Thank you,
Last updated: 2024-08-01

Sort by relevance or date