Post by tobifenny on Modbus TLS Kommunikation ^{CODESYS Forge talk (Post)}
Hier ist das handbuch: https://www.kostal-solar-electric.com/fileadmin/downloadcenter/kse/BA_KOSTAL_Interface_KSEM_DE.pdf Im Kapitel 1.3.2 ist das mit dem TLS beschrieben und in Kapitel 3.6.2 sind die Modbus-Register beschrieben.
Last updated: 2025-11-06

Post by ggaida on runtime dynamic modbus devices ^{CODESYS Forge talk (Post)}
Kurtk, I am working through a very similar scenario. I am curious if you have had any success since your post in implementing dynamic modbus configurations? Thx!
Last updated: 2025-11-20

Post by ggaida on runtime dynamic modbus devices ^{CODESYS Forge talk (Post)}
Kurtk, I am working through a very similar scenario. I am curious if you have had any success since your post in implementing dynamic modbus configurations? Thx!
Last updated: 2025-11-20

Post by paulorb on STRUCT AT %MW1000 ^{CODESYS Forge talk (Post)}
Hi I am trying to use STRUCT to parse commands from Modbus/TCP, Modbus client will fill the bytes related to a specific command (type, parameters), then PLC (Codesys) will access the command parameters. A STRUCT will simplify a lot the process of parsing the data, so I don't need to parse byte per byte, address will be mapped to a struct and I can use it for parsing the data. From what I understood, the compiler does not allow me to specify the location of the struct for a %MW register. VAR_COMMAND AT %MW1002: structGenericModbusCommand; This will throw: Bad declaration, use '%ML' for 'structGenericModbusCommand' variable But If I change it to %ML, when you go online you see that it is actually allocating the struct in another memory address. When we go online, on GVL we can see: VAR_COMMAND. structGenericModbusCommand %ML1002 commandType COMMANDTYPE %MB8016 ... %MB8020 I am not specifying a pointer or a reference it is a struct type, why is it mapping to a %MW location (random one). How can I control where it is mapping to? I need a consistent way to map STRUCT to specific modbus address. Is it possible? Thanks, Paulo Note I am using a Codesys OEM: Schneider Machine Expert Logic Builder (M241)
Last updated: 2024-08-13

Post by andrea199403 on Assigning Modbus addresses to a structure in a dynamic way ^{CODESYS Forge talk (Post)}
Hello everyone, I am new to this forum and I am also new to Codesys programming. My problem is this: I have a STRUCT of 64 bool and 30 real, this STRUCT is assigned in the programme 9 times. Now I need to communicate with an HMI via Modbus and I have defined the slave device and created the holding registers for communication. I would like to declare the first call of the STRUCT on the Modbus registers %QX2000.0 to %QX2007.7 for the booleans and on the registers %QW1004 to %QW1034 for the real registers. That said, I would like to change an index and set an offset of 100 bytes for the calls of the other 8 assignments, so that the result is: %QX2100.0 to %QX2107.7 for the booleans and on the %QW1104 to %QW1134 registers for the Real registers, etc. Is there a way to declare this? Thank you very much.
Last updated: 2025-10-21

Post by dawidr on Best practices for querying multiple MODBUS devices ^{CODESYS Forge talk (Post)}
Hi! What are the best practices for querying multiple Modbus devices? Single PRG or maybe multiple PRG (so basically multiple thread) per each Modbus device. In my current implementation I'm using single PRG and I'm utilizing FbMbMasterMultiQuerySerial and WagoAppPlcModbus.FbDigitalTwinMbSlaveDevice in eCockpit with PFC200. I've the timer with 2 seconds delay there and it was working fine for single device. But now I have three Modbus devices and for two of them I need to run 2/3 queries to get data from all registers. I noticed that the delays for getting the data from the Modbus devices is much bigger right now.
Last updated: 2024-07-31

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by attarzade on Servo motor as an slave and AC motor as an Mster ^{CODESYS Forge talk (Post)}
Hello, I would like to control a servo motor via EtherCAT as a slave axis, and have it follow a master axis that is driven by a Control Techniques C200 AC drive (ethercat communication).Could anyone help me with how to achieve this setup? I use codesys version 3.5.20 and crevis Ethercat cards. AC drive is master axis and Servo drive is slave axis Thanks in advance
Last updated: 2025-07-14

Post by tama00 on Raspberry Pi 4 als SPI Slave ^{CODESYS Forge talk (Post)}
Hallo zusammen, grundsätzlich sollte ja die Möglichkeit bestehen den Raspberry auch als SPI Slave zu nutzen. Leider habe ich kein entsprechendes Projekt gefunden, bei dem dies der Fall war. Kann mir jemand dabei weiter helfen, wie ich bei Codesys Control for Raspberry , die Konfigurationen für den SPI Slave machen kann? Der Master soll ein Microkontroller sein von einem anderen Gerät sein. Ich arbeite noch mit 4.10.0.0 und einem Raspberry Pi 4 Vielen Dank und liebe Grüße
Last updated: 2024-03-19

Post by simover on TCP/IP client ^{CODESYS Forge talk (Post)}
HELLO thank for you answer!! I'm a beginner can you give me an example?
Last updated: 2023-12-19

Post by kislov on Disable Communications to 'Modbus_Server_COM_Port' from the logic ^{CODESYS Forge talk (Post)}
Modbus_Slave_COM_Port.Enable := FALSE; where "Modbus_Slave_COM_Port" - slave device name from Device Tree
Last updated: 2024-08-30

Post by gatto on library ModbusTCP Slave 4.1.0.0 - function block ModbusServer ^{CODESYS Forge talk (Post)}
I've always liked codesys, but sometimes it drives me crazy
Last updated: 2024-11-28

Post by struccc on library ModbusTCP Slave 4.1.0.0 - function block ModbusServer ^{CODESYS Forge talk (Post)}
:) Yeah... Definitely not a "boring" platform, they are nice to give us work for the upcoming years... :)
Last updated: 2024-12-02

Post by dkugler on Direct Pointers in IOMapping for EtherCAT with IoDrvEthercatLib.ETCSlave_Dia ^{CODESYS Forge talk (Post)}
rmaas: how do you get the reference of the slave?
Last updated: 2024-02-13

Post by rmaas on Direct Pointers in IOMapping for EtherCAT with IoDrvEthercatLib.ETCSlave_Dia ^{CODESYS Forge talk (Post)}
The reference used is the ethercat slave name. For example in this screenshot the reference would be: EL1809_1
Last updated: 2024-02-13

Post by dkugler on EtherCAT fieldbus ^{CODESYS Forge talk (Post)}
There is an example for activating/deaktivating an optional Slave in the FAQ's: https://faq.codesys.com/pages/viewpage.action?pageId=49283084
Last updated: 2024-04-12

Post by boehli on canOPEN ^{CODESYS Forge talk (Post)}
Hallo, gibt es einen codesys Treiber oder Unterstützung für Hilscher canOPEN Slave oder Master Karten?
Last updated: 2024-05-15

Post by xiaonyan on Generic EtherCAT slave ^{CODESYS Forge talk (Post)}
Thanks for the reply. so where can i get this help from...the new post or link....where can i find it
Last updated: 2024-05-17

Post by greenwood on CODESYS Control Raspberry Pi mit Servotreiber T6 von StepperOnline ^{CODESYS Forge talk (Post)}
Kleines Update; mit dem richtigen Adapter und Kabel läuft jetzt auch der Slave. Herzlichen Dank noch mal!
Last updated: 2024-06-06

Sort by relevance or date