Post by ducng on SMC_ERROR.SMC_AXIS_NOT_READY_FOR_MOTION when using Drive Virtual ^{CODESYS Forge talk (Post)}
I'm using drive virtual and cannot run the motion command. Please help.
Last updated: 2025-11-26

Port instantiation of serial interface in WAGO PLC using Modb_L05.lib in CoDeSys v2.3 ^{CODESYS Forge talk (Thread)}
Port instantiation of serial interface in WAGO PLC using Modb_L05.lib in CoDeSys v2.3
Last updated: 2025-12-01

Post by eoahe on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hey Guys :) I have the following Problem using Modbus via Codesys: I'm trying to implement a Modbus Device into my codesys project. The device is a Router from Teltonika (RUT956) and it can communicate via Modbus. Currently I'm trying to implement it into my codesys prject as a slave and I'm using my windows computer as master. As it is not a codesys device (the codesys application is not uploaded to device as it has its own software) I'm having problems requesting and reading registers from the router. I've set up my windows computer as Master and implemented the router as slave. When I go online on my master device it sais that it has established a connection to the slave (router)(So I'm thinking this could work as there is a connection?). The goal is to read the GPS (latitude and longitude) data and on the homepage of teltonika you can find the register address and number of registers (adress 143 for latitude and 145 for longitude; both have a number of two registers). I've found tutorials how to read specific registers via their register address with other modbus programs (like modbus-cli), but as my entire project is established in codesys I was hoping to read these specific registers via codesys so that I can show the GPS data on my dashboard. I've tried establishing slave channels but that hasn't been working. I tried read input register channels of the length 4 but it's not possible to define specific register addresses to read via codesys so that didn't work (I jsut get a slaves device failure) and I've also tried establishing 516 (total number of registers the router sends I think?) read inputregister channels but that has the samle failure... So i guess the problem I'm having is establishing slave channels to read these specific registers. Does anyone know how to tackle this problem and has maybe had the same problem? Or maybe someone knows a workaround? I'm quite new to codesys so maybe I'm also lacking expertise...
Last updated: 2025-03-01

Post by andrax on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Hi, Communication with the ADS1115 is actually simple. 1. write config 2. write address pointer 3. read conversation register The ADS1115 works like a multiplexer. This means that you do this individually for each channel that you want to read. e.g: Channel 1: write config > write address pointer > read conversation register Channel 2: write config > write address pointer > read conversation register Channel 3: write config > write address pointer > read conversation register Channel 4: write config > write address pointer > read conversation register then you start again from the beginning You can also omit individual channels or read only one. It doesn't matter. I have written the driver so that I can also use it on the TCA9548. The driver is from Stefan Dreyer. In your case, the driver works and communication with the ADS1115 is running. As you can see, the cfgWrong:=FALSE If you could not write or read data, cfgWrong:=TRUE; This means that either something is wrong with your ADS1115 or you have connected something incorrectly. Question: what voltage do you want to measure?
Last updated: 2024-11-08

Post by dkugler on csv datei einlesen und verarbeiten ^{CODESYS Forge talk (Post)}
in der https://store.codesys.com/de/codesys-iiot-libraries-sl.html ist u.a. die CSV Utility SL Bibliothek incl. Beispiel enthalten. Die kostet etwas. Generell Codesys Beispiele findest Du hier: https://content.helpme-codesys.com/de/CODESYS%20Examples/_ex_start_page.html Alternativ file read verwenden und Zeit investieren um von Hand zu Fuß den Dateiinhalt zu durchforsten: https://content.helpme-codesys.com/de/CODESYS%20Examples/_ex_cds_file_utilities.html In der OSCAT Library gab es mal noch etwas, da könnte google weiterhelfen
Last updated: 2024-10-28

Post by sigurdrb on send appliaction files to wago plc (codesys 3.5) via ssh ^{CODESYS Forge talk (Post)}
Hi, I was hoping I could send the two files "application.app" and "application.crc" directly to the directory "/home/codesys/PlcLogic/Application" instead of logging into the device with codesys, downloading the program to the controller and then do the "create boot application", so it will reboot with the correct program running. I think i also need to edit the file "eRUNTIME.cfg" located in the "/home/codesys/ folder, because when I create the boot application from the codesys IDE, these lines are added to the file: [CmpApp] Application.1 = Application [SysFileMap] /home/codesys/PlcLogic/Application/Application.app=0x212520, 0x2DBC747E, 2DBC747E.app I think the "eRUNTIME.cfg" file is the same as CODESYSControl.cfg I also dont know the purpose of the hexadecimal numbers etc. that is generated. When I tried to replicate what codesys was doing, I placed the same files in the same folder as when codesys generated the boot file. And also added the lines in the eRUNTIME.cfg file: [CmpApp] Application.1 = Application [SysFileMap] /home/codesys/PlcLogic/Application/Application.app The controller did not boot up with any program, so my method did not work at all. I guess these lines tells the controller to run an application and where to find it? Could any of you help me with the best way to get the compiled program to the controller without using codesys or wago-software?
Last updated: 2024-05-28

Post by jonathan1321351 on IO-Link read/write parameters Ethernet/IP ^{CODESYS Forge talk (Post)}
I want to read and write parameters of an IO-Link device using acyclic messages. I have a Cube67+ in Ethernet/IP, connected to an IO-Link master. In the datasheet, I can find the parameters required for the message (Service, Class, Instance, etc.). I see the function block "Set_attribute_single" in the "EthernetIP Services" library, but I'm not sure how to correctly send the index and sub-index for the IO-Link device. The class in the datasheet is 0x80 for the IO-Link Parameter Object, but it’s not present in the CPIClass enum. Is there another function block more suitable for configuring IO-Link devices? (similar to "iol_call" in PROFINET or what’s used in EtherCAT).
Last updated: 2024-09-04

Post by mkintegration on Reading Absolute Encoder Position From Yasakawa Drive ^{CODESYS Forge talk (Post)}
I am looking to read in the absolute position of a yaskawa servo drive Sigma 7 that is using absolute encoder. It looks like yaskawa outputs this across there CN1 I/O connecter and during operation just outputs encoder pulses. But at boot up transmits the Multiturn data position and the Position within one rotation (pulse train) on two different wires. Once the drives are enabled it just uses incremental pulses. Does any one have experience with what IEC blocks to use to read this information in. I attached the Yaskawa Manual section that talks about the format.
Last updated: 2025-02-26

Post by mkintegration on Reading Absolute Encoder Position From Yasakawa Drive ^{CODESYS Forge talk (Post)}
I am looking to read in the absolute position of a yaskawa servo drive Sigma 7 that is using absolute encoder. It looks like yaskawa outputs this across there CN1 I/O connecter and during operation just outputs encoder pulses. But at boot up transmits the Multiturn data position and the Position within one rotation (pulse train) on two different wires. Once the drives are enabled it just uses incremental pulses. Does any one have experience with what IEC blocks to use to read this information in. I attached the Yaskawa Manual section that talks about the format.
Last updated: 2025-02-26

Post by jens on Modbus tcp - channel ^{CODESYS Forge talk (Post)}
Help wanted This is the first time i'm doing a Modbus Tcp project. I have some VLT with a extension module MCA-122. i'm currently unable to write to the VLT slave, but i can read from status word parameter=1603 and address := 16029 where the address is calculated from parameter is ((id x 10)-1). in the manual the functions that are supported are 3 hex, 6 hex, 10 hex, b hex and 11 hex. read holdin registers, write single register, write multiple registers, get comm. event counter, report slave id. i'm only using the Modbus Slave Channel is this wrong when trying to write to the vlt ?
Last updated: 2024-06-13

Post by jeffgamsby on Accessing ModbusTCP addresses from python ^{CODESYS Forge talk (Post)}
Hi, I am new to modbusTCP and I am trying to access Input registers from codesys (3.5.SP13). The offset is 16#0000 and I am trying to access Channel 1[24] %IW24 to pull analog values. I am using pyModbusTCP and I need to supply a modbus address and the number of registers to read. What does 16#0000 mean in terms of the actual offset, how do I translate this number plus the channel to access this info via python? Any help would be appreciated, thank you.
Last updated: 2023-09-20

Post by liamb on Converting CANbus to Decimal from signed 2's complement ^{CODESYS Forge talk (Post)}
I need to combine two 8 bit CANbus messages to 16 bits signed int then convert to decimal Decimal from signed 2's complement. I've been using the below code to read for new messages, combine them then assign them to a variable What is the best way to do this for from signed 2's complement? fbRxMessage351(Data := RxMessage351Data); IF fbRxMessage351.NewMessage THEN ChargeVoltage := (WORD_TO_REAL((RxMessage351Data[0]) + ((RxMessage351Data[1]) * 256))) * 0.1; END_IF
Last updated: 2024-08-16

Post by mostafa-beshr on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on implementing continuous movement in Codesys, but I've run into some trouble. I've tried using ALL SM3 Basic and SML without success. I’m specifically looking for a library that supports continuous updates and can fetch values from a server in real time. Does anyone know of a library or approach that fits these requirements? Any advice or suggestions would be greatly appreciated! i read plcopen documentaion as well as codesys Thank you!
Last updated: 2024-09-11

Post by mostafa-beshr on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on implementing continuous movement in Codesys, but I've run into some trouble. I've tried using ALL SM3 Basic and SML without success. I’m specifically looking for a library that supports continuous updates and can fetch values from a server in real time. Does anyone know of a library or approach that fits these requirements? Any advice or suggestions would be greatly appreciated! i read plcopen documentaion as well as codesys Thank you!
Last updated: 2024-09-11

Post by mostafa-beshr on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on implementing continuous movement in Codesys, but I've run into some trouble. I've tried using ALL SM3 Basic and SML without success. I’m specifically looking for a library that supports continuous updates and can fetch values from a server in real time. Does anyone know of a library or approach that fits these requirements? Any advice or suggestions would be greatly appreciated! i read plcopen documentaion as well as codesys Thank you!
Last updated: 2024-09-11

Post by camjam on BOOL variable in OPC UA and modbus simultaneously ^{CODESYS Forge talk (Post)}
I have come across this. The only way i could get it to work would be to define a word that is also the same address as the Bools. eg %MX600.0 through to %MX600.15 would be individually defined in the variables and them have another variable word defined at %MW300. You still need to break out the word in what ever program you are using to read/write the OPCUA tags.
Last updated: 2025-08-18

Post by astutoski on MCP23017: inputs OK, but outputs won’t switch (CODESYS on Raspberry Pi) ^{CODESYS Forge talk (Post)}
Hi everyone, I’ve connected and configured an MCP23017 over I²C on a Raspberry Pi using the available CODESYS/RPi library. Input reading works fine (I can reliably read a digital input). However, I can’t get any output pin to change state. Example: when I try to drive PB0, the watch shows MCP23017.Out_B.0 = TRUE (1), but there is no actual output on the pin (no voltage change). Anyone solved this?
Last updated: 2025-09-17

Post by usacodesysuser on How to connect serial devices ? ^{CODESYS Forge talk (Post)}
@eschwellinger do you have any examples of using a USB barcode scanner? I have read through the forums here and I am unable to find how to get the barcode data to populate in a text field without having to first click into the text field to activate it. Is there a library that allows you to access the barcode data? I am really new to this in general any help is greatly appreciated, hopefully you have a pretty clear example
Last updated: 2024-01-06

Post by wehling-h on PI Input value ^{CODESYS Forge talk (Post)}
Hi geoweil, have you tried to save changed values to remanent area or using a VAR RETAIN? After restart you have to initialize Counter with last remanent value. Depending on changes per cycle and the possibilitiy of your control unit to write remanent storage. Otherwise you need a buffering system to ensure save backup of last PI_Counter value. May you could read this Thread to get further help: https://forge.codesys.com/forge/talk/Engineering/thread/31e1c8349e/#bf48
Last updated: 2024-01-12

Post by ph0010421 on General question about library versions ^{CODESYS Forge talk (Post)}
Hello I can't find anything to read on the subject so I'll ask here. Up to now, when adding a (for example) Modbus Master, I've selected the version <= the RT version, so if I'm using SP13 Patch 3, I can use a library that doesn't exceed this. I've no idea if this is correct, but it's always worked. Can someone explain the 4.x.x.x libraries that have appeared; are they tied to a RT version? The controller I use is now at SP18Patch60, so should I continue to use 3.5.xxx or change? thanks
Last updated: 2024-05-29

Post by voffi on projects.open not working for file based storage project ^{CODESYS Forge talk (Post)}
Hello! Opening a project from a python script given at the CODESYS command line does not work for me with a file based storage project. Example: Running projects.open("test.project", primary = True) works but converting the project to a file based storage project and then give the folder name as an argument to project.open Running projects.open("test.fbsproj", primary = True) does not work. We decided to work with file based storage for the project. Is there a scripting API for file-based storage to e.g. convert it while running the script back or how to open file based storage project with projects.open? Thank you! voffi
Last updated: 2025-09-05

Post by gmau on RS232 Communication in CODESYS Control RTE V3 ^{CODESYS Forge talk (Post)}
Hello, I would like to implement RS232 communication into CODESYS Control RTE V3. I was writing the program testing it on CODESYS Control Win V3, where it worked fine. When I changed it to RTE, the communication was on, but I cannot send the data between PLC and scale - there is no or little response from scale - mostly one time receive and that is it. On Win V3 it was working fine. I read that I am supposed to configure CODESYSControl file for a proper communication using RTE, but even after that I can not get a stable and working communication. I am attaching my CODESYSControl and CODESYSControlUser data below, as well as I am sending the code from communication function. The communication should be through COM1 port of PC. CODESYS Version: CODESYS V3.5 SP21 + (64-bit) Runtime + Version: CODESYS Control RTE V3 Version 3.5.21.0 / CODESYS Gateway V3 - x64 Version 2.5.21.0 I would be much gratefull for any help. Sincerely,
Last updated: 2025-07-16

Post by seesle on Extracting information out of a *.library or *.compiled-library file ^{CODESYS Forge talk (Post)}
Hey there, is there a way to extract any data out of a .library or a .compiled-library file? Do you have any tools or a description of the binary or something like this to get for example the referenced libraries of a *.library file or any other stuff? Thx in advance M.
Last updated: 2023-12-04

Post by hua-huang on Compile problem - can't get .bin or .h86 file ^{CODESYS Forge talk (Post)}
Hello, I am programming for IFM controller CR7132, after I check 'create binary file of the application' and 'rebuild all', there is no error when compiling but no .bin or .h86 file generated. Could someone please inform the correct way? Thanks in advance! BR, Hua
Last updated: 2024-09-12

Post by csu-chris on No file found ^{CODESYS Forge talk (Post)}
I'm having trouble getting started with the SysFile library. I tried copying and running the code found here: https://forge.codesys.com/forge/talk/Engineering/thread/f17c3d0e64/ Every time I try to run the file handle pointer returns: 16#FFFFFFFFFFFFFFFF <dereference of="" invalid="" pointer=""></dereference> I can see the file when I look in the Device -> Files window Any idea what I'm doing wrong?
Last updated: 2024-10-15

Sort by relevance or date