Post by nixola on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hi, I added the following lines to /etc/codesyscontrol/CODESYSControl_User.cfg: [CmpCharDevice] PermittedPath.0=/dev/i2c* PermittedPath.1=/dev/spidev* PermittedPath.2=/sys/class/gpio/* PermittedPath.3=/dev/gpiochip* However, I'm still unable to read or control GPIO pins from any CODESYS application. Specifically, setting the pin direction (and, thus, the IoDrvGpioSysfs driver configuration) fails, with a rather non-descript error in the logs: Description Component Setting direction failed for GPIO pin 586 IEC Update configuration failed from driver IoDrvGPIOSysfs CmpIoMgr I'm running CODESYS Control for Linux ARM64 SL version 4.21.0.0; it's running in rootless mode, as the codesyscontrol user, but said user is in the gpio group and can otherwise normally interact with GPIO, both via gpioset/gpioget and via the sysfs driver in /sys/class/gpio/. The system is a custom 64-bit Raspberry OS based distro, running on a Raspberry Pi CM5 on kernel 6.18.34 with PREEMPT_RT scheduling.
Last updated: 2026-07-21

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
Good morning, I'm digging into this topic because I'm curious about resolving my problem in a test environment. In my previous message, I asked about the CODESYS Safe Timeprovider SL package (4.18.0.0), which I saw in the illustration. I noticed that it runs as a service. I am asking about this because from the perspective of an "ordinary" user, this service provides easier access to the settings of the time provider's operating parameters. The basic time provider configuration is outlined at https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_virtual_safe_time_provider.html. Why my questions? They stem from my specific case, which is experiencing timeout issues. I know that my environment is currently only a test environment. I'm assuming a real-world scenario in which I won't be able to achieve a better result with my configuration, and I will ultimately need to increase the time provider's cycle time. By running the time provider service, I can easily influence the time provider's operation and thus eliminate the problem. I know, I know, safety systems are not life-enhancing extras.
Last updated: 2025-11-19

Post by rita56re on →Temu Coupon Code $100 Off [^•^''act892435^•^''] First Order in Canada→→ ^{CODESYS Forge talk (Post)}
The TEMU $100 Off Coupon Code "act892435" Canada is an all-in-one opportunity that offers a $100 off and 50% discount! The TEMU $100 Off Coupon Code "act892435" offers an impressive $40 Off and a 40% discount on purchases for both new and existing customers in Canada. This special offer is a fantastic opportunity to save significantly on your TEMU shopping experience in Canada. By using the 40 Off Coupon Code "act892435" Canada, you can unlock the $100 coupon bundle, which provides $120 worth of savings. This means that you can enjoy a $100 discount on your order in Canada, as well as access to exclusive deals and additional savings opportunities in Canada. ⇦ Exclusive Temu coupon Codes Canada, ,,,act892435 ,,, ➤ Offers Canada → Discounts, Student Deals & More Canada ╰┈➤ Best Temu $100 Off Coupon Code Canada ➤ "act892435" ⇨ "act892435" ➥ Up to 50% Off Canada To redeem the TEMU $100 40 Off Coupon Code Canada, simply follow these steps: Sign up for a TEMU account on their website or mobile app in Canada. Add items worth $100 or more to your shopping cart in Canada. During checkout, enter the 40 Off Coupon Code "act892435" Canada in the designated field. The $100 discount will be automatically applied, and you can also enjoy an additional 50% off on your purchase in Canada. This 40 Off Coupon Code is valid for both new and existing TEMU customers in Canada, making it a great opportunity for everyone in Canada to save on their shopping. The $100 coupon bundle Canada can be combined with other available discounts, such as the 30% off code for fashion, home, and beauty categories, allowing you to maximize your savings in Canada. ➥ Temu Coupon Code $100 Off Canada {act892435} ➥ Temu Coupon Code 40 Off Canada {act892435} ➥ Temu Coupon Code 50 Off Canada {act892435} ➥ Temu Coupon Code 70 Off Canada {act892435} ➥ Temu Coupon Code 90 Off Canada {act892435} ➥ Temu Coupon Code 30 Off Canada {act892435} ➥ Temu Coupon Code First Order Canada {act892435} ➥ Temu Coupon Code Existing User Canada {act892435} Overall, the TEMU 40 Off Coupon Code "act892435" Canada is an excellent way to save a significant amount on your purchases in Canada, with a $100 discount and a 50% discount on top of that. Take advantage of this fantastic offer in Canada and enjoy the benefits of shopping with TEMU in Canada. Are you looking for the best deals on TEMU in Canada? Look no further! The TEMU 40 Off Coupon Code "act892435" Canada offers an incredible $100 off and a whopping 50% discount on your purchases in Canada. Whether you're a new customer in Canada or a loyal shopper, this code will maximize your savings and enhance your shopping experience in Canada. Let’s dive into the details and discover how you can make the most of this fantastic offer in Canada. Why Choose TEMU Canada? TEMU is a popular online marketplace in Canada, known for its wide range of products, competitive prices, and excellent customer service in Canada. From electronics and fashion to home goods and beauty products, TEMU has something for everyone in Canada. With regular promotions and discounts in Canada, TEMU ensures that you get the best value for your money in Canada. How to Use the TEMU 40 Off Coupon Code "act892435" Canada Using the TEMU 40 Off Coupon Code "act892435" Canada is straightforward. Follow these simple steps to unlock your $100 off and 50% discount in Canada: Visit the TEMU Website or App: Go to the official TEMU website or open the TEMU app on your mobile device in Canada. Browse and Shop: Explore the extensive range of products and add your desired items to the shopping cart in Canada. Proceed to Checkout: Once you’ve finished shopping, click on the cart icon and proceed to checkout in Canada. Enter the 40 Off Coupon Code: In the 40 Off Coupon Code field in Canada, enter "act892435" and click apply. Enjoy Your Savings: Watch the total amount drop as the $100 off and 50% discount are applied to your order in Canada. Benefits of Using TEMU 40 Off Coupon Code "act892435" Canada Significant Savings: Enjoy a substantial discount on your total purchase in Canada, making it easier to buy more for less. Wide Range of Products: The 40 Off Coupon Code is applicable to a vast selection of items in Canada, ensuring you can use it on the products you need and love. Easy to Use: The straightforward process of applying the 40 Off Coupon Code ensures a hassle-free shopping experience in Canada. Frequent Promotions: TEMU regularly offers promotional codes and discounts in Canada, so keep an eye out for more great deals in the future. Tips for Maximizing Your Savings on TEMU Canada Sign Up for the Newsletter: Stay updated on the latest promotions, new arrivals, and exclusive offers by subscribing to the TEMU newsletter in Canada. Follow TEMU on Social Media: Follow TEMU on platforms like Facebook, Instagram, and Twitter for real-time updates on sales and special deals in Canada. Download the App: The TEMU app in Canada often features app-exclusive discounts and offers, making it a great way to save more. Shop During Sales Events in Canada: Keep an eye out for major sales events like Black Friday, Cyber Monday, and seasonal sales for additional discounts in Canada.
Last updated: 2024-10-26

Post by rita56re on Temu coupon code ⁠╭⁠☞ {act892435}: ~||$100 off in Canada ^{CODESYS Forge talk (Post)}
The TEMU $100 Off Coupon Code "act892435" Canada is an all-in-one opportunity that offers a $100 off and 50% discount! The TEMU $100 Off Coupon Code "act892435" offers an impressive $40 Off and a 40% discount on purchases for both new and existing customers in Canada. This special offer is a fantastic opportunity to save significantly on your TEMU shopping experience in Canada. By using the 40 Off Coupon Code "act892435" Canada, you can unlock the $100 coupon bundle, which provides $120 worth of savings. This means that you can enjoy a $100 discount on your order in Canada, as well as access to exclusive deals and additional savings opportunities in Canada. ⇦ Exclusive Temu coupon Codes Canada, ,,,act892435 ,,, ➤ Offers Canada → Discounts, Student Deals & More Canada ╰┈➤ Best Temu $100 Off Coupon Code Canada ➤ "act892435" ⇨ "act892435" ➥ Up to 50% Off Canada To redeem the TEMU $100 40 Off Coupon Code Canada, simply follow these steps: Sign up for a TEMU account on their website or mobile app in Canada. Add items worth $100 or more to your shopping cart in Canada. During checkout, enter the 40 Off Coupon Code "act892435" Canada in the designated field. The $100 discount will be automatically applied, and you can also enjoy an additional 50% off on your purchase in Canada. This 40 Off Coupon Code is valid for both new and existing TEMU customers in Canada, making it a great opportunity for everyone in Canada to save on their shopping. The $100 coupon bundle Canada can be combined with other available discounts, such as the 30% off code for fashion, home, and beauty categories, allowing you to maximize your savings in Canada. ➥ Temu Coupon Code $100 Off Canada {act892435} ➥ Temu Coupon Code 40 Off Canada {act892435} ➥ Temu Coupon Code 50 Off Canada {act892435} ➥ Temu Coupon Code 70 Off Canada {act892435} ➥ Temu Coupon Code 90 Off Canada {act892435} ➥ Temu Coupon Code 30 Off Canada {act892435} ➥ Temu Coupon Code First Order Canada {act892435} ➥ Temu Coupon Code Existing User Canada {act892435} Overall, the TEMU 40 Off Coupon Code "act892435" Canada is an excellent way to save a significant amount on your purchases in Canada, with a $100 discount and a 50% discount on top of that. Take advantage of this fantastic offer in Canada and enjoy the benefits of shopping with TEMU in Canada. Are you looking for the best deals on TEMU in Canada? Look no further! The TEMU 40 Off Coupon Code "act892435" Canada offers an incredible $100 off and a whopping 50% discount on your purchases in Canada. Whether you're a new customer in Canada or a loyal shopper, this code will maximize your savings and enhance your shopping experience in Canada. Let’s dive into the details and discover how you can make the most of this fantastic offer in Canada. Why Choose TEMU Canada? TEMU is a popular online marketplace in Canada, known for its wide range of products, competitive prices, and excellent customer service in Canada. From electronics and fashion to home goods and beauty products, TEMU has something for everyone in Canada. With regular promotions and discounts in Canada, TEMU ensures that you get the best value for your money in Canada. How to Use the TEMU 40 Off Coupon Code "act892435" Canada Using the TEMU 40 Off Coupon Code "act892435" Canada is straightforward. Follow these simple steps to unlock your $100 off and 50% discount in Canada: Visit the TEMU Website or App: Go to the official TEMU website or open the TEMU app on your mobile device in Canada. Browse and Shop: Explore the extensive range of products and add your desired items to the shopping cart in Canada. Proceed to Checkout: Once you’ve finished shopping, click on the cart icon and proceed to checkout in Canada. Enter the 40 Off Coupon Code: In the 40 Off Coupon Code field in Canada, enter "act892435" and click apply. Enjoy Your Savings: Watch the total amount drop as the $100 off and 50% discount are applied to your order in Canada. Benefits of Using TEMU 40 Off Coupon Code "act892435" Canada Significant Savings: Enjoy a substantial discount on your total purchase in Canada, making it easier to buy more for less. Wide Range of Products: The 40 Off Coupon Code is applicable to a vast selection of items in Canada, ensuring you can use it on the products you need and love. Easy to Use: The straightforward process of applying the 40 Off Coupon Code ensures a hassle-free shopping experience in Canada. Frequent Promotions: TEMU regularly offers promotional codes and discounts in Canada, so keep an eye out for more great deals in the future. Tips for Maximizing Your Savings on TEMU Canada Sign Up for the Newsletter: Stay updated on the latest promotions, new arrivals, and exclusive offers by subscribing to the TEMU newsletter in Canada. Follow TEMU on Social Media: Follow TEMU on platforms like Facebook, Instagram, and Twitter for real-time updates on sales and special deals in Canada. Download the App: The TEMU app in Canada often features app-exclusive discounts and offers, making it a great way to save more. Shop During Sales Events in Canada: Keep an eye out for major sales events like Black Friday, Cyber Monday, and seasonal sales for additional discounts in Canada.
Last updated: 2024-10-26

Post by rita56re on Temu coupon code ⁠╭⁠☞ {act892435}: ~||$100 off in Canada ^{CODESYS Forge talk (Post)}
The TEMU $100 Off Coupon Code "act892435" Canada is an all-in-one opportunity that offers a $100 off and 50% discount! The TEMU $100 Off Coupon Code "act892435" offers an impressive $40 Off and a 40% discount on purchases for both new and existing customers in Canada. This special offer is a fantastic opportunity to save significantly on your TEMU shopping experience in Canada. By using the 40 Off Coupon Code "act892435" Canada, you can unlock the $100 coupon bundle, which provides $120 worth of savings. This means that you can enjoy a $100 discount on your order in Canada, as well as access to exclusive deals and additional savings opportunities in Canada. ⇦ Exclusive Temu coupon Codes Canada, ,,,act892435 ,,, ➤ Offers Canada → Discounts, Student Deals & More Canada ╰┈➤ Best Temu $100 Off Coupon Code Canada ➤ "act892435" ⇨ "act892435" ➥ Up to 50% Off Canada To redeem the TEMU $100 40 Off Coupon Code Canada, simply follow these steps: Sign up for a TEMU account on their website or mobile app in Canada. Add items worth $100 or more to your shopping cart in Canada. During checkout, enter the 40 Off Coupon Code "act892435" Canada in the designated field. The $100 discount will be automatically applied, and you can also enjoy an additional 50% off on your purchase in Canada. This 40 Off Coupon Code is valid for both new and existing TEMU customers in Canada, making it a great opportunity for everyone in Canada to save on their shopping. The $100 coupon bundle Canada can be combined with other available discounts, such as the 30% off code for fashion, home, and beauty categories, allowing you to maximize your savings in Canada. ➥ Temu Coupon Code $100 Off Canada {act892435} ➥ Temu Coupon Code 40 Off Canada {act892435} ➥ Temu Coupon Code 50 Off Canada {act892435} ➥ Temu Coupon Code 70 Off Canada {act892435} ➥ Temu Coupon Code 90 Off Canada {act892435} ➥ Temu Coupon Code 30 Off Canada {act892435} ➥ Temu Coupon Code First Order Canada {act892435} ➥ Temu Coupon Code Existing User Canada {act892435} Overall, the TEMU 40 Off Coupon Code "act892435" Canada is an excellent way to save a significant amount on your purchases in Canada, with a $100 discount and a 50% discount on top of that. Take advantage of this fantastic offer in Canada and enjoy the benefits of shopping with TEMU in Canada. Are you looking for the best deals on TEMU in Canada? Look no further! The TEMU 40 Off Coupon Code "act892435" Canada offers an incredible $100 off and a whopping 50% discount on your purchases in Canada. Whether you're a new customer in Canada or a loyal shopper, this code will maximize your savings and enhance your shopping experience in Canada. Let’s dive into the details and discover how you can make the most of this fantastic offer in Canada. Why Choose TEMU Canada? TEMU is a popular online marketplace in Canada, known for its wide range of products, competitive prices, and excellent customer service in Canada. From electronics and fashion to home goods and beauty products, TEMU has something for everyone in Canada. With regular promotions and discounts in Canada, TEMU ensures that you get the best value for your money in Canada. How to Use the TEMU 40 Off Coupon Code "act892435" Canada Using the TEMU 40 Off Coupon Code "act892435" Canada is straightforward. Follow these simple steps to unlock your $100 off and 50% discount in Canada: Visit the TEMU Website or App: Go to the official TEMU website or open the TEMU app on your mobile device in Canada. Browse and Shop: Explore the extensive range of products and add your desired items to the shopping cart in Canada. Proceed to Checkout: Once you’ve finished shopping, click on the cart icon and proceed to checkout in Canada. Enter the 40 Off Coupon Code: In the 40 Off Coupon Code field in Canada, enter "act892435" and click apply. Enjoy Your Savings: Watch the total amount drop as the $100 off and 50% discount are applied to your order in Canada. Benefits of Using TEMU 40 Off Coupon Code "act892435" Canada Significant Savings: Enjoy a substantial discount on your total purchase in Canada, making it easier to buy more for less. Wide Range of Products: The 40 Off Coupon Code is applicable to a vast selection of items in Canada, ensuring you can use it on the products you need and love. Easy to Use: The straightforward process of applying the 40 Off Coupon Code ensures a hassle-free shopping experience in Canada. Frequent Promotions: TEMU regularly offers promotional codes and discounts in Canada, so keep an eye out for more great deals in the future. Tips for Maximizing Your Savings on TEMU Canada Sign Up for the Newsletter: Stay updated on the latest promotions, new arrivals, and exclusive offers by subscribing to the TEMU newsletter in Canada. Follow TEMU on Social Media: Follow TEMU on platforms like Facebook, Instagram, and Twitter for real-time updates on sales and special deals in Canada. Download the App: The TEMU app in Canada often features app-exclusive discounts and offers, making it a great way to save more. Shop During Sales Events in Canada: Keep an eye out for major sales events like Black Friday, Cyber Monday, and seasonal sales for additional discounts in Canada.
Last updated: 2024-10-26

Post by timvh on VisuElems.CurrentUserGroupId is not stable ^{CODESYS Forge talk (Post)}
I'm not sure what you are trying to do, but getting the CurrentUserGroupID like this will not work, because there could be multiple Visualization Clients and each can have a different user that is logged in. Also when you go online with CODESYS and open an Visualization, this is counted as a client. Probably this is the reason you see it changing. What you can to is "iterate" over all clients and then see which user is logged in on which visualization Client. For this you need to add the Visu Utils library to the project and call the FbIterateClients. See https://content.helpme-codesys.com/en/libs/Visu%20Utils/4.4.0.0/VisuUtils/VisuActionUtilities/Function-Blocks/FbIterateClients.html fbClientIteration( xExecute := x_Execute, itfClientFilter := VU.Globals.AllClients, itfIterationCallback := fbIterator, xDone => x_Done, xBusy => x_Busy, xError => x_Error, eError => e_Error); The fbIterator, in the example above, should be an instance of an FB which you have created yourself and this must implement VU.IVisualizationClientIteration. For example: FUNCTION_BLOCK FB_ITERATOR IMPLEMENTS VU.IVisualizationClientIteration Then automatically the corresponding methods will be called. In the HandleClient Method, you will get an interface to the client(s) and then you can get the current user through this interface: itfClient.UserGroupId You can also get the UserName: itfClient.UserName
Last updated: 2023-11-14

Post by open on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
Hi @ph0010421, I tried the program the TimeTaken is calculated when stop is triggered. I want the TimeTaken to be continuously calculated and counting when a BOOL variable is true. I tried to program this way: Declaration: PROGRAM PLC_PRG VAR bStartStop: BOOL := FALSE; // Start/Stop button bReset: BOOL := FALSE; // Reset button bRunning: BOOL := FALSE; // Flag indicating whether the stopwatch is running tStartTime: TIME; // Variable to store the start time tElapsedTime: TIME; // Variable to store the elapsed time END_VAR Implementation: // Main program logic IF bReset THEN // Reset button pressed, reset the stopwatch bRunning := FALSE; tElapsedTime := T#0s; ELSIF bStartStop THEN // Start/Stop button pressed, toggle the running state IF bRunning THEN // Stop the stopwatch bRunning := FALSE; ELSE // Start the stopwatch bRunning := TRUE; tStartTime := tElapsedTime; END_IF; END_IF // Update the elapsed time when the stopwatch is running IF bRunning THEN tElapsedTime := tElapsedTime + T#1s; // Adjust the time increment as needed END_IF However counting of the seconds is not accurate. I tried changing the main task cycle time interval to 1000ms. The counting of seconds become slower. (see attached) Please help
Last updated: 2023-12-08

Post by pouyavakili on Execute Codesys Tests with python ^{CODESYS Forge talk (Post)}
Thank you for your input! What I'm ultimately trying to achieve is automated test execution as part of a CI/CD pipeline (e.g. in GitLab or Azure DevOps). For this, I need to: Open a CODESYS project via script Build the project Run the Test Manager tests from a .TestRepository.xml Collect test results (e.g., pass/fail + a report) Exit with a proper return code (for pipeline success/failure) To integrate this into automation, I’m using the CODESYS scripting engine via Python (headless), but the issue is that the get_testmanager() function isn't available on the project object — even though Test Manager is installed, licensed, and works interactively in the IDE. Are you suggesting that I should: Use the Test Manager GUI to script the logic with its internal scripting language? Or is there a way to launch the Test Manager in headless/scripted mode, while still being able to control things via Python? If there's a supported way to automate tests with the Test Manager using scripting, especially from pipelines or headless environments, I’d really appreciate any pointers or example workflows. Thanks again!
Last updated: 2025-07-24

Post by imdatatas on MC_MoveAbsolute: C0138: No matching 'FB_Init' method found for instantiation of SMC_MoveAbsRelPerformerImpl [ERROR] ^{CODESYS Forge talk (Post)}
Dear @gseidel, Thank you for your reply. The exact version of Codesys and its compiler was 3.5.21.20. The compiler version was fixed and could not be changed in project settings. Since I couldn't continue due to this compilation error, I temporarily overcame this issue as follows. -- I completely uninstalled Codesys 3.5.21.20 and completely deleted the Codesys folder in the C:\ProgramData folder. -- I restarted my computer and installed Codesys 3.5.19.70. -- I updated the Codesys Installer and all its add-ons to the latest versions. -- The project that was giving me the compilation error I mentioned before is now open with Codesys 3.5.19.70, compiled it, and successfully downloaded it on the device. -- I haven't encountered the same problem anymore. I think this issue is related to SP21 and its compiler. Frankly, I'd expect a project created with an older version to compile without errors after opening it with the latest Codesys version and updating all libraries. Regards, imdatatas
Last updated: 2025-09-26

Post by jrsantab on Remote connection to ifm PLC & HMI ^{CODESYS Forge talk (Post)}
We have finally solved the problem. The version of the Gateway in the computer that worked (3.5.11.0) and the one that didn't (3.5.17.30) was different. We have three different Codesys 3.5 versions installed because we work with different controllers. I believe that, depending on the sequence you follow to install the versions you get a different Gateway version. To solve the problem you first have to disable the "obsolete" services. Open services, serach for (in our case) CODESYS Gateway V3 Version 3.5.11.0 CODESYS ServiceControl Version 3.5.11.0 I stopped the services and changed to Manual Start. Then you have to create the new services. In our case, from a Command Prompt session (cmd): SC CREATE "Codesys GatewayService Rigual" binpath="C:\Program Files\CODESYS 3.5.17.30\GatewayPLC\GatewayService.exe" and then SC CREATE "CODESYS ServiceControl Version 3.5.17.30" binpath="C:\Program Files\CODESYS 3.5.17.30\GatewayPLC\CODESYSControlService.exe" remember also to set them as Automatic Start!
Last updated: 2024-04-22

Post by jroddball79 on PM556-TP-ETH — How to change IP address without overwriting the PLC program? ^{CODESYS Forge talk (Post)}
Hi, I need to change the IP address of an ABB PM556-TP-ETH using ABB Automation Builder. The situation is: I have connectivity to the PLC using the current IP (configured in Communication Settings) Online Login works fine The Network Scan does not detect the PLC IP-Configuration tool shows all fields disabled I don't have the original project source, only an empty project The PLC has no SD card inserted The Online menu does not show an Upload option When I modify the IP in the project and connect, Automation Builder shows: "The PLC configuration needs to be updated. A full PLC download is required" I'm afraid a full download will overwrite the running program. Is there any way to change only the IP address without overwriting the application? I'm also open to solutions using third-party tools, Python scripts, or any other method (DCP protocol, direct TCP communication, etc.) as long as it doesn't overwrite the running application. Thank you
Last updated: 2026-05-19

Post by fajean on Issue with library updates ^{CODESYS Forge talk (Post)}
We make heavy use of internally developed libraries, which are often nested on multiple levels. I routinely work simultaneously on several libraries along with a project that use them. I make changes to a library and immediately perform a download (online or otherwise) in the project. For the longest time, we had zero issue with this. But starting a good while back, with 3.5 SP19 I think, CODESYS started not noticing library updates in other instances most of the time. When the update is missed, the project sees no need to update the code, and any download ignores the new code. A "Clean all" does not solve the issue. But if I close and then re-open the project, then the new version is noticed and the download works. The other solution is saving the library to the registry multiple times (say, 20-30 times, less if lucky), and then at some point the project notices the changed library. I am now on SP21, and it is still not fixed. This is driving me mad, any tasks probably takes me double the time or more due to this problem. My colleague has the same problem on a separate computer. Is this a known issue? Is there a setting somewhere that changes how updates are checked? Thanks for any help!
Last updated: 2026-02-13

Post by timvh on USB Game Controller with Raspberry Pi ^{CODESYS Forge talk (Post)}
I'm not sure it will work, but you could try it with the CmpCharDevice library. You could create a function block that looks something like this: As input for the filename, you have to use your Linux device, e.g.: '/dev/input/event0' '/dev/input/by-path/platform-button@23-event' Off course you must also pass the pointer to the memory where the data can be written to and the size (count in number of bytes) of the buffer. FUNCTION_BLOCK FB_CharDevice VAR_INPUT szFilename: STRING; pbyBuffer : POINTER TO BYTE; udCount : UDINT; END_VAR VAR_OUTPUT iState : INT := 0; nrBytesRead : DINT; END_VAR VAR xInit : BOOL := TRUE; dFlags: DINT := CmpCharDevice.ACCESS_MODE.O_RDONLY + DINT#4000; // see details for flags: http://linux.die.net/man/2/open, + DINT#4000 is for non-blocking hDevice: CmpCharDevice.CmpCharDevice_Implementation.RTS_IEC_HANDLE := -1; Result : CmpCharDevice.CmpCharDevice_Implementation.RTS_IEC_RESULT; END_VAR IF xInit THEN hDevice := CmpCharDevice.CDOpen(szFilename, dFlags ,Result); // if it would not succeed, the result is -1 (Invalid handle) IF hDevice <> 16#FFFFFFFF AND Result = 0 THEN iState := 5; END_IF xInit := FALSE; END_IF IF iState = 5 THEN nrBytesRead := CmpCharDevice.CDRead(hDevice, pbyBuffer, udCount, Result); ELSE nrBytesRead := 0; END_IF Make sure you close the connection properly, maybe by overwriting the default FB_Exit method of the FB: // Clean up device IF hDevice <> 16#FFFFFFFF THEN __TRY CmpCharDevice.CDClose(hDevice,Result); __CATCH ; __ENDTRY iState := 0; END_IF
Last updated: 2026-05-01

Post by elektron785 on GPIO mit Codesys Virtual Control for Linux ARM64 SL ^{CODESYS Forge talk (Post)}
Hallo zusammen, ich möchte an einem Entwicklungsboard auf dem der i.MX 8M Plus von NXP aufgesteckt ist die vier zur Verfügung gestellten GPIOs als Ausgänge verwenden. Ich habe mir dazu die Readme-Datei des GPIO-Beispiels von "C:\Program Files\CODESYS 3.5.20.40\CODESYS\CODESYS Control SL Extension Package\4.14.0.0\Examples\GPIO" angeschaut Die Übersicht der verfügbaren GPIOs sieht folgendermaßen aus - wobei ich das auf die reduziert habe, die für mich von Interesse sind: gpiochip0: GPIOs 0-31, parent: platform/30200000.gpio, 30200000.gpio: gpio-0 (SODIMM206 ) gpio-1 (SODIMM208 ) gpio-2 ( ) gpio-3 ( ) gpio-4 ( |sd-vsel ) out hi gpio-5 (SODIMM210 ) gpio-6 (SODIMM212 ) gpio-7 (SODIMM216 ) gpio-8 (SODIMM218 ) gpio-9 ( ) gpio-10 ( ) gpio-11 (SODIMM16 ) gpio-12 (SODIMM155 |regulator-usb1-vbus ) out lo gpio-13 (SODIMM157 ) gpio-14 (SODIMM185 |regulator-usb2-vbus ) out hi gpio-15 (SODIMM91 )** Füge ich nun das GPIO (1 Bit)-Gerät in meinem Codesys-Programm hinzu funktioniert der Bus solange bis ich die Richtung in den GPIO-Parametern von "not used" auf "Output" stelle (siehe Bild gpio_parameter). Dann funktioniert nach Download der Bus nicht mehr. Gibt es noch eine andere Möglichkeit das zu steuern oder muss ich noch Einstellungen tätigen? Für die Zeile mit dem echo (export/unexport) aus dem Beispiel fehlen mir trotz sudo die Zugriffsrechte. "The Kernel Linux has deprecated GPIO user space SysFS. However, the kernel config CONFIGGPIOSYSFS is still enabled on Toradex's BSP to support customers using it in their legacy applications. You can check the configuration by running zcat /proc/config.gz | grep CONFIGGPIOSYSFS. For GPIO access from userspace, the new char device API, also known as libgpiod, must be used." Dies steht in der Verwendung der GPIOs - eine Ausführung des zcat-Kommandos liefert ein =y zurück.
Last updated: 2025-03-17

Post by dnordenberg on BOOL variable in OPC UA and modbus simultaneously ^{CODESYS Forge talk (Post)}
How can I have an BOOL variable that is read/write in both modbus TCP server and from OPC UA at the same time? Variables with %MX.n %QX.n addressing which is used for BOOL/coils in modbus server is not allowed in OPC UA symbol list on Schneider M251 controllers. I have already asked on Schneiders forum but there are not a lot of codesys experts over there :( So OPC symbols can't have a address and the modbus TCP server needs a address. So how should I do it then? It seems like an impossible combination. Since I want read/write access from both ways I can't just simply make a second variable and assign it the value of another since it would be a one way assignment. I also tried using VAR_CONFIG which then makes the address syntax %Q or %M in my main variable list and that fools OPC UA Symbol Configuration to allow it and then I add the complete %MX.n address of it in the VAR_CONFIG list. This semi works, I can toggle the BOOL from modbus but the OPC UA symbol seems to be read only. It displays symbol status but nothing happens when I toogle it. I think I need another way to have the variables and symbols pointing to the same bits in memory... My plan B is to write a BOOL array compare FB that saves a history bit from previous cycle and if that does not match current status at next cycle for either the OPC symbol or the modbus variable then it copies the new status over to the other. Maybe ugly but it's like my last alternative. Kind regards David
Last updated: 2025-07-14

Post by timvh on Get Alarm status in Codesys ^{CODESYS Forge talk (Post)}
You are right, that you can use the GetState method, but it is not that simple. You first have to get a list of (filtered) alarms from the AlarmManager. You can find an example in Forge how to do this. See https://forge.codesys.com/prj/codesys-example/alarm-manager/home/Home/ Then you can go through this list to get the state of all the (filtered) alarms. See below the code which you could use. This is all based on the example from forge. Create a program: // This example shows how to access alarms via structured text. PROGRAM PLC_PRG VAR xInit : BOOL := TRUE; udiResult : UDINT; fbAlarmFilterCriteriaAll : FB_AlarmFilterCriteriaAll; fbAlarmManagerClient : FB_AlarmManagerClient; itfAlarmManagerClient : IAlarmManagerClient := fbAlarmManagerClient; xAlarm1 : BOOL; xAlarm2 : BOOL; xWarning : BOOL; iNrOfAlarmsInAlarmList : INT; iNrOfActiveAlarmsInAlarmList : INT; paitfAlarm: POINTER TO ARRAY [0..0] OF AlarmManager.IAlarm; iAlarmIndex : INT; eAlarmState: AlarmManager.AlarmState; END_VAR IF xInit THEN xInit := FALSE; fbAlarmManagerClient.itfAlarmFilterCriteria := fbAlarmFilterCriteriaAll; // register alarm client to get updated about alarm status / changes udiResult := AlarmManager.g_AlarmHandler.RegisterClient(itfAlarmManagerClient, 0, 0); END_IF // Polling the number of alarms udiResult := AlarmManager.g_AlarmHandler.GetActiveAlarms(itfAlarmManagerClient, parritfActiveAlarms => paitfAlarm, iCountActiveAlarms => iNrOfAlarmsInAlarmList); iAlarmIndex := 0; iNrOfActiveAlarmsInAlarmList := 0; WHILE iAlarmIndex < iNrOfAlarmsInAlarmList DO eAlarmState := paitfAlarm^[iAlarmIndex].GetState(); IF eAlarmState = AlarmManager.AlarmState.Active OR eAlarmState = AlarmManager.AlarmState.ActiveAcknowledged THEN iNrOfActiveAlarmsInAlarmList := iNrOfActiveAlarmsInAlarmList + 1; END_IF iAlarmIndex := iAlarmIndex + 1; END_WHILE See below some details about the function blocks: One function block should implement the IAlarmFilterCriteria interface. This can be empty except a few methods. FUNCTION_BLOCK FB_AlarmFilterCriteriaAll IMPLEMENTS AlarmManager.IAlarmFilterCriteria Method implementation (others related to interface are empty) METHOD AreAllAlarmClassesSelected : BOOL AreAllAlarmClassesSelected := TRUE; METHOD AreAllAlarmGroupsSelected : BOOL AreAllAlarmGroupsSelected := TRUE; METHOD GetPriorityFrom : USINT GetPriorityFrom := 0; METHOD GetPriorityTo : USINT GetPriorityTo := 255; The other function block should implement IAlarmManagerClient and get a reference to the FB which implements the IAlarmFilterCriteria FUNCTION_BLOCK FB_AlarmManagerClient IMPLEMENTS AlarmManager.IAlarmManagerClient VAR_INPUT itfAlarmFilterCriteria: AlarmManager.IAlarmFilterCriteria; END_VAR Method implementation (others related to the interface are empty) METHOD GetFilterCriteria : AlarmManager.IAlarmFilterCriteria // see VAR_INPUT for filter GetFilterCriteria := itfAlarmFilterCriteria; Off course you have to add the AlarmManager to your application and add some alarms to it.
Last updated: 2025-09-02

Post by john-robinson on Limiting Memory Access of an Array to Within its Bounds ^{CODESYS Forge talk (Post)}
Recently we had an issue regarding some simple code to calculate a rolling average. The code indexes from zero to 199 to properly store the current input into a circular buffer which then allows us to calculate a rolling average: VAR input_5s : REAL; outs_arr : ARRAY[0..199] OF REAL; i : USINT := 0; END_VAR ___ //this code runs every five seconds, calculating a rolling average outs_arr[i] := input_5s; i := i + 1; output := OSCAT_BASIC.ARRAY_AVG(ADR(outs_arr), SIZEOF(outs_arr)); IF i >= SIZEOF(outs_arr) THEN i := 0; END_IF There is a simple bug in this code where the index will be set to 0 when it has surpassed the length of the array in bytes (800 in this case) rather than larger than the number of reals in the array (200). The solution here is simple, replacing i >= SIZEOF(outs_arr) with i >= SIZEOF(outs_arr)/SIZEOF(outs_arr[0]). In this example when the index increased to 201 and the line outs_arr[201] := input_5s was called, codesys arbitrarily wrote to the address in memory that is where outs_arr[201] would be if the array was that long. I would like to find a way to wrap the codesys array inside of a wrapper class that checks if an input is within the bounds of an array before writing to that value. I know how I would implement that for a specific array, I could create a method or class that takes an input of an array of variable length, ie. ARRAY[*] OF REAL, but I don't know how to make this for any data type. I am wondering if anyone has ever done anything similar to this, or has any better suggestions to ensure that none of the programmers on this application accidentally create code that can arbitrarily write to other locations in memory.
Last updated: 2024-03-05

Post by mp9876 on Device logon problem following fresh install ^{CODESYS Forge talk (Post)}
All screenshots are enclosed in MS Word document. NOTE; 4 questions features at the end. Any assistance would be greatly appreciated! Hi everyone, I am still having device logon problem following a fresh install Here are the STEPS I went through following a FRESH CODESYS Win 64 3.5.19.60 install on a different computer. ‘Gateway not configured properly’ when attempting to REFRESH from the Users and Groups. Then did Gateway manage and confirmed it was ok: This message popped out as it was a fresh install: YES then: Initially went with Administrator twice (user & password) but it did not like it. No device is responding to …: Continued by setting a new user Pressed OK and obtained the following message: Stopped and Restarted PLC at that point: Obtained the following: Attempted to login a 2nd time without success. Then I scanned the network to see if matching device can be detected: Only way to get it detected was to remove the tick in the ‘Hide non-matching devices…’ Attempted a WINK but got a return like this one: REFRESH either @ Users and Groups or @ Access Rights returns: Then created user ‘mp’ at Project level ang logged in: Understandably device user mp9876 was not valid for the Project. Device information A few questions comes to my mind following these connection attempts: 1- Gateway not configured properly message pops out because of a non-compatible device ? 2- Why would the device not be compatible ? 3- Any way to make the device compatible ? 4- Any ideas on how to get this connectivity problem to the device solved ?
Last updated: 2024-03-17

Post by alexgooi on Codesys KNX implementation ^{CODESYS Forge talk (Post)}
Dear forum, We are currently doing some research on the Codesys KNX implementation (https://store.codesys.com/en/codesys-knx-sl.html). We almost have it working but we are missing the last part. The setup: We have a Codesys virtual control container running on docker (4.17.0.0), the I/O is running over an Ethernet IP coupler (Weidmüller), and this is running fine. As far as I’m concerned this tells me that the ethernet device is working properly (the container has access to the outside world, including multicast). Underneath this ethernet adapter the KNX module is added (see picture). In the KNX device (Codesys) 2 input variables are added (see picture), and these are exported to ETS (ETS 5). In ETS A Codesys KNX device has been imported and the Codesys export was imported, afterwards the group addresses are attached to the variables (see picture). Afterwards this configuration is downloaded to the Codesys controller (Container) via ETS. ETS asks for the pressing of the programming button, when the virtual programming button is pressed the download starts and finishes without any errors. This tells me that ETS is communicating with the Codesys controller, and that the download process is ok (so far so good). Now the part where we are struggling with, somehow we need to convert the KNX TP to KNX IP. For this we have the following interface: Zenio KIPI SC (https://www.zennio.com/product/kipi-sc/) this is a KNX TP to IP interface. We have the following setup for this device (see picture) (an IP in the same subnet is used). We tried multiple combinations of IP addresses but the TP devices are simply not communicating to the Codesys container. Does anyone has any advice on what to try next. To make the question more explicit how can we link the TP bus to the Codesys device? Kind Regards Alex
Last updated: 2026-01-05

Post by wold on CodeMeter Network Server: Keep runtime dongle local-only and export only a second CmStick ^{CODESYS Forge talk (Post)}
Hello, I am running a CODESYS Control Runtime on a Raspberry Pi. Two CmSticks are connected to the same system: CmStick A - Runtime license - MultiCore license - KNX license CmStick B - Engineering / Developer licenses My goal is: The runtime on the Raspberry Pi shall use CmStick A locally. Licenses from CmStick A shall NOT be provided by the CodeMeter Network Server. Only licenses from CmStick B shall be available to remote network clients. During troubleshooting I observed that the CodeMeter Network Server collects licenses from both CmSticks. The KNX license appears to be local-only, but the runtime and multicore licenses of the same dongle are still visible through the server. I would like to know if a supported configuration exists for the following scenario: One CmStick remains strictly local to the runtime. A second CmStick on the same machine is exported through the CodeMeter Network Server. Questions: Is it possible to exclude a specific CmStick from being exported by the CodeMeter Network Server? Can this be configured via License Access Permissions (ACL), WebAdmin, or another mechanism? Can export rules be applied per CmStick, per Firm Code, or per Product Code? If supported, could you provide a configuration example or a reference to the relevant documentation? The reason for asking is that after removing a separately installed CodeMeter server component and returning to a local-only setup, the runtime licensing behaviour became stable again. Therefore I am looking for the officially supported way to keep the runtime dongle local while still providing engineering licenses from a second dongle over the network. Thank you.
Last updated: 2026-08-02

Post by dclements on Feature Request: Read-Only References / Pointer-to-Const Support ^{CODESYS Forge talk (Post)}
I would like to suggest adding support for persistent read-only references or pointers in CODESYS, similar to a C++ pointer-to-const (const T*). For example, something conceptually similar to: POINTER TO CONSTANT ST_MyData or REFERENCE TO CONSTANT ST_MyData The important distinction is that the reference itself may still be passed around or reassigned, but the referenced object cannot be modified through that reference. CODESYS currently supports VAR_IN_OUT CONSTANT, which provides read-only reference semantics for parameters, but there does not appear to be an equivalent type that can be stored in a variable or returned from a method. A practical use case is a registry that owns long-lived definitions. The registry needs to retain ownership of the data while downstream systems maintain persistent references to it. Currently, the main options are: Return the struct by value, which loses reference semantics and requires a copy. Return POINTER TO ST_Definition, which allows consumers to modify registry-owned data. Convert the structure into a Function Block and expose a getter-only interface, which provides the desired encapsulation but introduces more complexity and memory overhead. A read-only reference/pointer type would allow libraries to expose persistent, zero-copy access to internally owned data while preserving encapsulation. This would be particularly useful for library APIs and object-oriented CODESYS architectures where ownership of data should remain with one component while other components are allowed to observe it. Similar requests for constant references/pointers have been discussed on CODESYS Forge previously, so this appears to be a recurring use case rather than something specific to one application.
Last updated: 2 hours ago

Post by struccc on Inheritence of struct, ^{CODESYS Forge talk (Post)}
Strangely reminds me to my struggles... Want to do something "Elegant", reusable, universal, practical... In CODESYS??? 🙃 First of all, before you get too deep into this: If you could find a way, to make a "universal" log entry object, containing the variable length data itself, you wouldn't be able to store them in an array, or access them like an array, or pass them by value as a type. (please correct me, if I'm wrong, incorrect, or not precise). Because... Basically you can't declare a type with variable memory footprint. This is a very deeply embedded characteristic of CODESYS, and all IEC 61131-3 systems, and it has many reasons behind. And yes, it is a very common trap / mistake, to forget about. So, with a log entry - I guess - it's pretty much the purpose: store data and metadata together, and then handle it in a uniform way. There are ways to handle this, really depends on what is the purpose. For example: 1. Entries with fixed length (Maybe it is not as evil as it looks for the first time. Depends on the situation, but definitely the fastest and easiest code) You can have your base object, with an internal, fixed length string or byte array variable. I would go with a string, and call it _Data.; And then you can make properties, like As_Bool, As_Int, As_Real... In the 'set' accessors, you can do like: pReal := ADR(_Data); // POINTER TO REAL As_Real := pReal^; In the 'get' accessors, evidently: pReal := ADR(_Data); // POINTER TO REAL pReal^ := AS_Real; Or, can use ANY type, if you are not obsessed with variable / property like access: 2. Fixed length, but nicer First, some disadvantage to any values: - You can only assign values with write access. No literals, constants, etc... - Can only be used as input variable of function or function_block - Therefore, stg you could reach: LogEntry.Initialize (stVariable|rVariable|iVariable|xVariable); Just a quick example (it's funny to play with ANY): Be careful it was not tested. I'm sure can be done better, please feel free to comment FUNCTION_BLOCK FB_LogEntry VAR_INPUT MsgClass : UDINT; // Like DEBUG, WARN, ERR... MsgCode : UDINT; // Like Errors.ERR_FAILED MsgTS : DT; // The timestamp END_VAR VAR _Data : STRING(80); // Our data container... _Descr : __SYSTEM.AnyType; // A standard descriptor for our data, containing TYPE_CLASS, address and size END_VAR METHOD SET_Value : BOOL VAR_INPUT anyValue : ANY; END_VAR VAR I : DINT; diSize : DINT; pStr : POINTER TO STRING; END_VAR // Check what did we receive in anyValue. diSize := anyValue.diSize; // We use constant __SYSTEM.TYPE_CLASS to identify the received data type CASE anyValue.TypeClass OF // Maybe we don't want to store references, pointers... and who knows what else... __SYSTEM.TYPE_CLASS.TYPE_REFERENCE, __SYSTEM.TYPE_CLASS.TYPE_POINTER : SET_Value := FALSE; // For the planned types we will be just fine. TYPE_CLASS.TYPE_BOOL, TYPE_CLASS.TYPE_INT, TYPE_CLASS.TYPE_REAL : SET_Value := TRUE; // Optionally string can be handled separately, maybe we have received STRING(255), but practically it is shorter than 80 bytes... TYPE_CLASS.TYPE_STRING : pStr := anyValue.pValue; diSize := MIN(anyValue.diSize, LEN(pStr^) + 1); // Get the actual size, and rewrite the received structure member diSize := MIN(SIZEOF(_Data), diSize); // Can chop down the received string to our length... SET_Value := TRUE; // Maybe want to play a little bit more here, to narrow down or convert datatypes, etc... // Or just reject any other datatype ELSE SET_Value := FALSE; RETURN; END_CASE // Fail, if the received value is still larger than our container... IF diSize > SIZEOF(_Data) THEN SET_Value := FALSE; END_IF // Here we should be ok, just set up the _DataType structure, and copy store the data IF SET_Value THEN THIS^._Descr.TypeClass := anyValue.TypeClass; // The typeclass is already filtered THIS^._Descr.diSize := diSize; // Set the (adjusted) size THIS^._Descr.pValue := ADR(_Data); // This will not change, just to be sure {IF defined (pou:SysMem.SysMemCpy)} SysMem.SysMemCpy(_DataType.pValue, anyValue.pValue, TO_UDINT(anyValue.diSize)); {ELSE} // An ugly replacement MemCpy FOR I:=0 TO diSize - 1 DO _Descr.pValue[I] := anyValue.pValue[i]; END_FOR {END_IF} // Otherwise, in case of failure maybe better set an empty value (overwrite the former data descriptor) ELSE THIS^._Descr.TypeClass := TYPE_CLASS.TYPE_NONE; THIS^._Descr.pValue := ADR(_Data); THIS^._Descr.diSize := 0; END_IF METHOD GET_Value : BOOL VAR_INPUT anyValue : ANY; END_VAR VAR I : DINT; END_VAR // We just have to serve the data, using the __System.AnyType structure received // Roughly we can say: IF anyValue.TypeClass = _Descr.TypeClass AND anyValue.pValue <> 0 // This should not be possible, already taken care of by Codesys (?) THEN {IF defined (pou:SysMem.SysMemCpy)} SysMem.SysMemCpy(anyValue.pValue, _DataType.pValue, TO_UDINT(MIN(anyValue.diSize, _Descr.diSize))); {ELSE} // An ugly replacement MemCpy FOR I:=0 TO MIN(anyValue.diSize -1, _Descr.diSize - 1) DO anyValue.pValue[I] := _Descr.pValue[I]; END_FOR {END_IF} // Just to make sure, that our string is terminated... IF anyValue.TypeClass = TYPE_CLASS.TYPE_STRING THEN anyValue.pValue[anyValue.diSize -1] := 0; END_IF GET_Value := TRUE; RETURN; END_IF // ... But can play more CASE anyValue.TypeClass OF TYPE_CLASS.TYPE_WSTRING : ; // Could do conversion TYPE_CLASS.TYPE_XSTRING : ; // Wow, I have to figure this out TYPE_CLASS.TYPE_PARAMS : ; // BTW, what is this, how to use? TYPE_CLASS.TYPE_ANYNUM : ; // ... END_CASE Be careful it was not tested. I'm sure can be done better, please feel free to comment 3. If you really want to do entries with variable size In a standard environment, it would be similar to the previous, except you dont have the container variable _Data, just use a pointer, practically _Descr.pValue At Initialize (SET_Value), you have to allocate the memory, would be easy with SysMem.SysMemAlloc - nowadays with SysMem.SysMemAllocData -, and you make sure to release it after use with SysMem.SysMemFreeData... SysMemAlloc was already hidden. The problem with this, that sooner or later your application will totally fragment the dynamic memory, and fail... So should look for some form of dynMaybe MemUtils.MemoryManager (I am not sure what is the status and the future of it). 4. You will end up by a LogEntry Factory ... 5. You could still have a look at this IEC Snippets BTW, Standard Codesys Logger is not a bad choice either. If you are really interested, I share some more code / library.
Last updated: 2025-03-09

Post by struccc on Application failing to boot after system reboot ^{CODESYS Forge talk (Post)}
I started to experience the same issue, after upgrading to 3.5.19 , and still persists with 3.5.20.3 , using CodesysControlWinV3 x64 on Windows. Unfortunately, this is a live application, normally it is running for months without interruption - so it was a surprise at the last cold start... It was not possible to go online with the original version, so I couldn't see the application, or system status, just the log message. First time I manually clean the Application from the PlcLogic directory (there was no coredump file in there), then I could start the runtime service, and do a fresh download, and set the bootproject. I could not try a cold system reboot - it's in a 24/7 production environment, and I was under heavy pressure to start... What I did, I have created a backup from the * complete * runtime directory, from the failed, and fixed version - before and after download. This directory in my case C:\ProgramData\CODESYS\CODESYSControlWinV3x64\55096128 - At the next shutdown, it was sufficient to copy back this backup completely, and could start the runtime service afterwards. Ugly, but local staff with some skills can do it without programming tool... I don't store any live data, configuration, log files, persistent data in this directory - the only reason I need this is to edit the CodesysControl... .cfg file.... And to see the logfiles in emergencies like this. The application concerned doesn't use any retain area. - exactly for these reasons - Maybe that is causing the problem with the newer runtime versions As far as I see, this problem occurs only if the power of the Windows PLC is interrupted without a proper shutdown. Unfortunately, this can happen sometimes. The newer versions, seems tp modify CodesysControl.cfg on the fly, and register the applications, and bootproject information after download. (I don't really see CodesysControl.cfg a proper location for this... but that's just my feeling) So now I had a look at CodesysCotrol.cfg on my laptop and I found: [CmpRetain] ;Retain.SRAM.Size=0x200200 ;Retain.SRAM.Address=0xFA3C5776 ;SimulateSRAM=1 [CmpApp] ;Bootproject.CreateOnDownload=0 ;Bootproject.StoreOnlyOnDownload=0 ;Bootproject.InvalidateByRename=1 ;Bootproject.InvalidateBySetting=1 ;Bootproject.InvalidateNever=0 ;PersistentForce=0 ;RetainType.Applications=InSRAM ;RetainType.Applications=OnPowerfail ;RetainType.Applications=None ;Exception.Hardware.GlobalStop=1 Application.1=MyTestAppNoRetain The last line appeared after download and boot project creation. Maybe... Should set RetainType.Applications=None? I wonder about all these settings, but... Will write separately about it. I hope this helps a little...
Last updated: 2024-11-21

Post by patrik on Wish: CODESYSControl.cfg - again ^{CODESYS Forge talk (Post)}
Really good post. I hope that it gets seen by CoDeSys staff. I often find the documentation lacking when it comes to using CoDeSys in more complex ways. If using standard "basic PLC functionality", then it's fine and functions are documented in a sufficient way. Once you go outside of that bubble then I find the documentation not enough. CODESYSControl.cfg is a good example of this. And why isn't more of this integrated in the IDE. like changing port of the webserver. Why is it hidden in this file and not accessible through the IDE. It feels like a layer of complexity purposely left in so you don't change it if you don't know what you are doing. Like the argument is if you have the know-how to find the file you have the know-how to edit it. I find the documentation lacking when it comes to more complex libraries too. Like the element collections library. there is parameters I still don't quite know what they do. I can't find any documentation about them. There is an example project to download from CoDeSys so you can see how you are supposed to set your factories up. I leave some parameters like it is in the example. Should I? I don't know. Does it work. Yes. But I could perhaps create memory leaks if I get something wrong and I don't see that until way later. In the create method of your element factory you have a function called __vfinit and you just have to accept that it works. Why can't I get insight in what it does through documentation? Don't CoDeSys want us to know how these work so we can't use them to accidentally break something? I find the error logging lacking too. I've had the CoDeSys service crash but it doesn't say why. I've seen windows noticing the crash but no error code was sent or error message. Also in my current issue where the application fails to start after power outage. I can see in the log that it fails to load retain in the application as one log entry and application failing to start as another. But why? Why does loading the retain fail? give me more information! Is it just a skill issue with me? I don't know. If it is then I'd still want CoDeSys to step up their game when it comes to documentation. I'm sorry if a lot of frustration comes though in this post. I really like the product and what I can do with it compared to other PLC brands.
Last updated: 2024-11-21

Post by bertus on Can't get SMC_SmoothPath to work ^{CODESYS Forge talk (Post)}
Hello all, I am trying to run a XY trajectory from a static G-Code file. Everything works except the smoothing/blending of the corners. My setup: Codesys v3.5sp18 Raspberry Pi 4 CODESYS Control for Raspberry Pi SL, using demo license. Zero axes (only using the interpolator). The order of processing for my decoding is: SMC_NCDecoder (ok) SMC_SmoothMerge (ok) SMC_SmoothPath (not ok) SMC_LimitDynamics SMC_CheckVelocities I created following instances and buffers: fbNCDecoder: SMC_NCDecoder; fbSmoothMerge: SMC_SmoothMerge; fbSmoothPath: SMC_SmoothPath; fbLimitDynamics: SMC_LimitDynamics; fbCheckVelocities: SMC_CheckVelocities; aNCDecoderBuffer: ARRAY[0..49] OF SMC_GeoInfo; // buffer stage 1 (fbNCDecoder) aSmoothMergeBuffer: ARRAY[0..19] OF SMC_GeoInfo; // buffer stage 2 (fbSmoothMerge) aSmoothPathBuffer: ARRAY[0..99] OF SMC_GeoInfo; // buffer stage 3 (fbSmoothPath) aLimitDynamicsBuffer: ARRAY[0..39] OF SMC_GeoInfo; // buffer stage 4 (fbLimitDynamics) My original G-Code file has a lot of short G1 elements but this example, I reduced it to a simple square: N000 G51 D10 N010 G38 O1 N020 G00 X0 Y0 F50 E1000 E-1000 N030 G01 X0 Y-37.5 N040 G01 X-75 Y-37.5 N050 G01 X-75 Y37.5 N060 G01 X0 Y37.5 N070 G01 X0 Y0 N080 G50 N090 G39 O1 In the Codesys CNC settings, I have these instances activated: SMC_SmoothMerge SMC_SmoothPath SMC_LimitDynamics SMC_CheckVelocities And with those settings (and the path-preprocessing button actived), the G-Code viewer shows the square with nicely blended corners (see attached picture). However, when running it on the PLC, it doesn't blend the corners at all. Below the relevant part of my code. The process is started with bDecode. // stage 1: decoding G-code fbNCDecoder( ncprog := square, bExecute:= bDecode, bAbort:= NOT bDecode, nSizeOutQueue := SIZEOF(aNCDecoderBuffer), pbyBufferOutQueue := ADR(aNCDecoderBuffer) ); // stage 2: merge short linear segments fbSmoothMerge( bExecute := bDecode, poqDataIn := fbNCDecoder.poqDataOut, nSizeOutQueue := SIZEOF(aSmoothMergeBuffer), pbyBufferOutQueue := ADR(aSmoothMergeBuffer), piMaxDifference := PI_MAX_DIFFERENCE, usiMaxDegree := 5, wFeatureFlag := 1, wAdditionalParamNumber := 0, dMinimumCurvatureRadius := D_MIN_CURVATURE_RADIUS ); // stage 3: smooth corners fbSmoothPath( bExecute := bDecode, bAbort := NOT bDecode, poqDataIn := fbSmoothMerge.poqDataOut, eMode := SMC_SMOOTHPATHMODE.SP_SPLINE5_MIN_CURVATURE, eAddAxMode := SMC_SMOOTHPATHADDAXMODE.SPAA_NONE, nSizeOutQueue := SIZEOF(aSmoothPathBuffer), pbyBufferOutQueue := ADR(aSmoothPathBuffer), dAngleTol := D_ANGLE_TOL, bSymmetricalDistances := TRUE, bImprovedSymmetricCuts := TRUE ); // stage 4: keep acc/dec and velocity within limits fbLimitDynamics( bExecute := bDecode, bAbort := NOT bDecode, poqDataIn := fbSmoothPath.poqDataOut, wAxis := 16#07, nSizeOutQueue := SIZEOF(aLimitDynamicsBuffer), pbyBufferOutQueue := ADR(aLimitDynamicsBuffer), bIncludePathSettings := TRUE, dMaxVel := 2500, dMaxAccDec := 10000 ); // stage 5: check the path speed fbCheckVelocities( bExecute := bDecode, bAbort := NOT bDecode, poqDataIn := fbLimitDynamics.poqDataOut, dAngleTol := D_ANGLE_TOL); pathQueue := fbCheckVelocities.poqDataOut; // repeat until MaxDuration ... Any idea what I'm doing wrong? Is smooth path supposed to work at all when using a demo license? Thanks.
Last updated: 2025-12-17

Sort by relevance or date