Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0 ^{CODESYS Forge talk (Post)}
Hello, I am facing a problem with the new Softmotion 4.17.0.0 version. Has anyone encountered a similar problem, what is the solution? I would be happy if you could share it. Problem description: -- "SMC_FreeEncoder" encoder axis is the master, -- The motor of the servo driver on the EtherCAT bus is the slave axis. -- When the MC_CamIn block executed, the InSync output is activated. However, although the master encoder axis position value changes, there is no movement in the slave servo axis! Test steps: 1-) EtherCAT servo axis installed, configured and motion test was performed with MC_Jog. No problem. 2-) Softmotion general axis pool > SMC_FreeEncoder was added and pulse amount configuration was performed. No problem. 3-) Incremental encoder actual count value was transferred to the "SMC_FreeEncoder.diEncoderPosition" variable as DINT under the ethercat task in every cycle and the encoder axis position value was observed. No problem. 4-) A simple CAM table with a 1:1 ratio was created under the project tree. (For example: Simply, when the encoder rotates 1 turn, the motor will rotate 1 turn.) 5-) The SMC_FreeEncoder axis enabled with MC_Power and brought to the StandStill state. 6-) The MC_CamTableSelect block was run with default input values ​​(all absolute) and only the Cam table name was specified. The Done output was seen successfully. No problem. 7-) The MC_CamIn block was activated with default input values ​​(absolute) and only the master encoder axis name, slave servo axis name, CamTableID input pins was specified and then "Execute" input set to TRUE. 8-) The InSync output information of the MC_CamIn block observed as TRUE. However, although the encoder axis value changed, the position value of the slave axis did not change at all, it did not move. It always remained at 0.0mm. 9-) When I repeated the same steps above, only changing the master axis to SM_Drive_Virtual instead of FreeEncoder and gave movement to the virtual axis, this time the slave axis moved successfully. However, when the same steps and operations are performed with the same IDE just downgrade SoftMotion version from 4.17.0.0 to 4.10.0.0, everything works normally and without problems as expected in MC_CamIn block with FreeEncoder master. (By the way, The used IDE version is Codesys V3.5 SP20patch3.) Best Regards Imdat
Last updated: 2024-11-11

Post by schweizer on Position und Größe optimal anpassen (Container.Height - Visu.Height) funktioniert nicht. ^{CODESYS Forge talk (Post)}
Hallo Forum Hat jemand Erfahrung mit dem Optimalem anpassen der Position und Grösse der Visualisierungselemente? Bei uns funktioniert in der Codesys 3.5 SP20 nur die Anpassung auf der x-Achse mit (Container.Width - Visu.Width). Die y-Achse wird jedoch mit (Container.Height - Visu.Height) nicht beeinflusst. Wir haben dies nach dem Beispiel von Codesys "Position und Größe optimal anpassen" umgesetzt und keinen Erfolg. Besten Dank für eure Hilfe.
Last updated: 2024-07-29

Post by schweizer on Position und Größe optimal anpassen (Container.Height - Visu.Height) funktioniert nicht. ^{CODESYS Forge talk (Post)}
Hello forum Does anyone have experience with optimally adjusting the position and size of the visualization elements? For us, the adjustment on the x-axis works in Codesys 3.5 SP20 with (Container.Width - Visu.Width). However, the y-axis is not affected with (Container.Height - Visu.Height). We implemented this according to the example from Codesys "Optimally adjust position and size" and had no success. Thank you very much for your help.
Last updated: 2024-07-29

Post by trusty-squire on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
What do you mean by continuous movement? You want to continuously follow a dynamic target position? SMC_ControlAxisByPos, which is typically used with CNC Interpolators, could work for that. Instead of feeding the target position in from the Interpolator, feed in the target position from your server instead. Once you enable the FB, it will continuously move the axis to track the fSetPosition input. https://content.helpme-codesys.com/en/libs/SM3_CNC/Current/SM_CNC_POUs/SoftMotion-CNC/Direct-Axis-Control/SMC_ControlAxisByPos.html
Last updated: 2024-09-12

Post by balazska2 on Position values with integer variables ^{CODESYS Forge talk (Post)}
Hello guys! https://content.helpme-codesys.com/en/CODESYS%20Visualization/_visu_elem_label.html My question: Could I give an integer variable to the Position records (in the Element list => Position => width / height)? If yes, how? I defined a TEST integer variable with 300 value. I tried to add this variable to the width record (.TEST or only TEST), but if I saved, the value jumps back to 0. Thanks for your help! :)
Last updated: 2024-10-03

Post by arvindkumar on Wago plc not going back to RUN Mode after Power failure ^{CODESYS Forge talk (Post)}
Hi im using wago pfc750-8207 plc and my programming software was codesys v2.3, im facing some issue in my plc after power failure my plc not going back to run mode sometimes, i did sourecode download, boot application created and still facing this issue, out of 10 power failure 8 times its going to run mode some time its missing to go run mode and only sys indication is in on condition Kindly please help me.
Last updated: 2023-12-15

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Hello everyone, I have a very simple program for the process, but it's driving me crazy and I can't see the problems I'm left with: Short topological description: Dual Core Berghof controller with softmotion runtime version 3.5.19.30; Two axes with servodrive on canopen bus, clocked distributed from master; Ethercat I/O node; 2 ms ethercat task, 2 ms canopen bus cycle time; I/O objects of the canopen master and canopen drives connected to the ethercat task cycle; Problem 1: Two separate programs each manage their own axis and drive, with separate state machines. A first axis moves primarily in velocity, except having to position itself absolutely at a predetermined point at the end of the job; the second axis, on the other hand, is a paper unwinder that changes, for each job cycle, from actions in absolute, relative, and cam displacement with the master axis. Well, the state machine of both axes was written in such a way as to call running the useful FB and change it on state change in this way: CASE i_stateMachine OF 0: o_Power(Enable := TRUE, bRegulatorOn := FALSE, bDriveStart := FALSE, Axis := o_PaperUnwinderAxis); o_MoveAbs(Execute := FALSE, Axis := o_PaperUnwinderAxis); o_MoveRel(Execute := FALSE, Axis := o_PaperUnwinderAxis); o_CamSelect(Execute := FALSE, Master := o_MachineAxis, Slave := o_PaperUnwinderAxis, CamTable := cam_PaperUnwinder); o_CamIn(Execute := FALSE, Master := MachineEncoder, Slave := o_PaperUnwinderAxis); o_CamOut(Execute := FALSE, Slave := o_PaperUnwinderAxis); o_SetPosition(Execute := FALSE, Axis := o_PaperUnwinderAxis); IF ... THEN i_StateMachine := 10; END_IF; 10: o_Power( Enable := TRUE, bRegulatorOn := TRUE, bDriveStart := TRUE, Axis := o_PaperUnwinderAxis ); IF o_Power.Status THEN i_StateMachine := 20; END_IF; 20: (* Avanzamento carta *) o_MoveAbs( Execute := TRUE, Position := o_Somewhere, Velocity := 25.0, Acceleration := 3666.7, Deceleration := 3666.7, Jerk := 48000.0, Direction := MC_DIRECTION.positive, Axis := o_PaperUnwinderAxis ); IF o_MoveAbs.Done THEN o_MoveAbs(Execute := FALSE, Axis := o_PaperUnwinderAxis); i_StateMachine := 30; END_IF 30: d_HomingPosition := ...; o_SetPosition( Execute := TRUE, Position := d_HomingPosition, Mode := FALSE, Axis := o_PaperUnwinderAxis ); (* ... *) IF o_SetPosition.Done = TRUE THEN o_SetPosition(Execute := FALSE, Axis := o_PaperUnwinderAxis ); o_LogServer.Append(sMessage := '...', lscClass := LOGSERVER_CLASS.ALWAYS, sdt := o_CommonsMgrData.systime.sdtLocal); i_StateMachine := 40; END_IF; 50: ... The code above is a sketchy example of what I wanted to write. But it gives me a spot problem: in some, the state change results in a drive error, which is unrecoverable except with a reinitialization via SM3_ReinitDrive(). Things are improved a little if in the program I always run the call of all softmotion blocks in this way: o_Power(Axis := o_PaperUnwinderAxis); o_Jog(Axis := o_PaperUnwinderAxis); o_Halt(Axis := o_PaperUnwinderAxis); o_MoveAbs(Axis := o_PaperUnwinderAxis); o_MoveRel(Axis := o_PaperUnwinderAxis); o_CamIn(Master := MachineEncoder, Slave := o_PaperUnwinderAxis); o_CamOut(Slave := o_PaperUnwinderAxis); If I don't execute all the calls of all the motion FBs used, when exchanging machine state often (but not always), the axis goes into error with event id THE_FB_WASNT_CALL... Done a little diagnostics it seems that the FBs return the bDone, before they are completely terminated. I tried doing the machine state exchange not with the bDone bit of the FBs, but with the 'standstill' state of the axis. It didn't seem to change anything. Problem 2: During the use SM3_ReinitDrive() I get the erro in the log: "NetID 0: SDO read error for object 16#607C..." Assuming that the device involved it's one of the two servodrive, (no others device are present in the network), I don't found any object 0x607C in the 'possible object list in/out' of the two drive, and I don't understand where this object can be listed. So any ideas and suggestions regarding these two issues will be very, very welcome. If you need the source project, I am willing to send it.
Last updated: 2024-07-17

Post by gseidel on Beckhoff AS1060 and EL7041 configuration ^{CODESYS Forge talk (Post)}
Hi pmanuele, while I don't have firsthand experience with the EL7041 and the step motor AS1060, there are two things you can check: If you use an external encoder, please make sure you use the alternative device description calles "EL7041 1Ch. Stepper motor output stage (50V, 5A) Rev24 with external Encoder". The SoftMotion driver will set the feedback type automatically, and use the correct object for the actual position (16#6010:21 instead of 16#6010:20) If you have problems with changing the controller mode, I assume to velocity, please make sure you change the PDO mapping so that the actual velocity (16#6020:33) and set velocity (16#7010:33) are mapped by PDO. Hope this helps, Georg
Last updated: 2 days ago

Post by mubeta on parker servo and position ^{CODESYS Forge talk (Post)}
Reading between the lines of what you did not specify, it therefore seems to appear that in the programme, at the end of the movement order, there is an order to remove power and switch off the pulse modulation. if this is the case, it is obvious that the motor then remains free. If the position is to be maintained at the end of the movement, the motor current modulator, which on the PLC side is controlled via the MC_Power method, must not be interrupted. Another possibility is that in the motor drive settings, the standstill torque current is set very low or zero and without position monitoring. You have to check this via the servo motor drive.
Last updated: 2024-08-05

Post by niallel on CamBuilder and first boundary position not zero ^{CODESYS Forge talk (Post)}
Hi, I've read the CamBuilder documentation and it shows to use the left boundary of the first segment as SMCB.BoundImplicit(), so that the transition is as smooth as possible. With this it sets X and Y to 0. My first slave position is not 0 (say for example it's 100), so I would set it with SMCB.Bound(0,100). My question is that when the cam goes back to the start (Periodic := TRUE) , will it blend with the last position (360, 100) if I do this? I imagine it will, but the documentation isn't clear as the information in the Periodic Cams only says to set Smooth Transition in the cam properties - but when I'm defining it with code there isn't an option for Smooth Transition to be set. Hope this makes sense? Many thanks,
Last updated: 2024-10-23

Post by eschwellinger on Project compiling error in Simulation mode ^{CODESYS Forge talk (Post)}
I fear you need to update if you need a solution for this.
Last updated: 2023-09-08

Post by eschwellinger on Problem with edge gateway config mode ^{CODESYS Forge talk (Post)}
yes add in: c:\Windows\System32\config\systemprofile\AppData\Roaming\CODESYS\CODESYSGatewayV3\XXXXXXXX\Gateway.cfg [CmpEdgeGateway] MaintenanceMode=1
Last updated: 2024-10-21

Post by arnog on Two drives on one axis, Gantry Robot ^{CODESYS Forge talk (Post)}
Hi TK_Jenssen did you found a solution I am setting up the samelike gantry only with two z-axes which are mounted on fix position with an X axes between the two z-axes. The movement and position of both z-axes must be very well aligned and calibrated. Maybe also to be adjusted by programming. Can you sent an example of your solution?
Last updated: 2023-08-25

Post by rmaas on Responsive Design Example ^{CODESYS Forge talk (Post)}
Hi, I just tried the example project with control WIN x64 and for me this is working correct. The only difference is that it is showing 'TabletPortrait' when i hold my smartphone in portrait mode and 'Monitor' when i hold my smartphone in landscape mode. This is because smartphone resolutions have increased i guess... You could check what resoution is detected and change accordingly in IsSmartphone method.
Last updated: 2024-07-04

Post by kblundy on Change the Opening Position of the Dialog using VU.FbOpenDialog ^{CODESYS Forge talk (Post)}
I hope the community can help me with this. I need to use the Visu Utils FbOpenDialog to control the opening and closing of a dialog. I have the Opening and Closing working, but I can’t get the dialogue's position to be controlled. The code looks like this: PROGRAM OPEN_DIALOG VAR xOpenLatchSettingDialog : BOOL; TopLeftDialog : VisuStructPoint ; fbOpenLatchSettingsDialog : VU.FbOpenDialog ; END_VAR IF xOpenLatchSettingDialog THEN xOpenLatchSettingDialog:= FALSE ; TopLeftDialog.iX := 100; TopLeftDialog.iY := 23; fbOpenLatchSettingsDialog(sDialogName := 'visu_AlarmLatchSettings', xExecute := xOpenLatchSettingDialog , xModal := TRUE, itfClientFilter := VU.Globals.OnlyTargetVisu, pTopLeftPosition := ADR(TopLeftDialog)); CloseVisuDialog(sDialogName:= 'visu_AlarmLatchSettings'); ELSE xOpenLatchSettingDialog:= TRUE ; IF fbOpenLatchSettingsDialog.xError THEN xOpenLatchSettingDialog := FALSE; END_IF END_IF I can't seem to work out a way to make the values in TopLeftDialog.iX and TopleftDialog.iY be passed correctly in the call and for it to change the position of the dialogue box. The code is compiled, but the position has not been changed. Any guidance or suggestions for revising this code would be incredibly valuable. Your insights could be the key to solving this issue.
Last updated: 2024-05-05

Post by mubeta on parker servo and position ^{CODESYS Forge talk (Post)}
With this kind of motor nominal tourque I can belive that it can be moved very easy. 1,6 Nm is, for example, the torque required for unscrew a small loose cap from a bottle.
Last updated: 2024-08-05

Post by mubeta on parker servo and position ^{CODESYS Forge talk (Post)}
In general, drives have parameter sets to adjust behaviour in such cases: position recovery, adaptation with resistant torque, out-of-position window failure, etc. (Much depends on the type of configuration set for the axis: positioner, speed controller, torque controller, etc.). I have used that type of drive very little, in only two cases and a long time ago. To tell you what is normal is impossible. I know by reputation they are very simple objects, without too many pretensions and adjustments possible. Try running traces by monitoring actual position, motor current, torque and following error. These are the most sensible curves to understand what is going on. Maybe by fine tuning the motor tuning, the current controller or the speed controller you will get something closer to what you want. For example, from DS, the motor has a standstill torque of 3 Nm. Observe with traces whether this is effective: motor current trend. And afterwards, when you have your own accurate picture of the situation, you can also hear from the product's local support to see if you can steal a few more things from it performance-wise.
Last updated: 2024-08-05

Post by mubeta on parker servo and position ^{CODESYS Forge talk (Post)}
... you say 1.6 Nm is only enough torque to unscrew a loose bottle cap ... This the the value of torque: from 1,2 Nm to 1,4 Nm that is cosidered acceptable for an old people. 1,6 Nm the torque considered acceptable for general use caps.
Last updated: 2024-08-07

Post by rmaas on CSV file and string manipulation. ^{CODESYS Forge talk (Post)}
the $N stands for newline and $R stands for line break. maybe these combinations are considered as 1 character/position? Not sure, just a thought... see also: https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_operands_constant_string.html#:~:text=A%20string%20constant%20is%20a,belong%20to%20this%20character%20set.
Last updated: 2024-09-27

Post by batuhanarslan on Dynamic Image Show ^{CODESYS Forge talk (Post)}
Hello Everyone, I have 5 images with same position in the screen. I would like to pass around them with giving an GlobalIndexImageId how can I do it. In properties part I don't understand the which one is doing that. Best Regards
Last updated: 2024-10-13

Post by dagi89 on CAA File open Problems ^{CODESYS Forge talk (Post)}
Dear All, i am using Runtime CODESYS Control Win V3 - X64 Version 3.5.20.40, by using CAA file library (3.5.19.0) seems not fasible to open a file n 'C:\ciao.txt' or others absolute path. The error on File Open is 5114 File Operation Danied.. here below the implemented code and the windows file's properties. I use to implement codesys in RPI and this operation is immediate... Can someone help me in it?? Thanks in advance Dagi89
Last updated: 4 days ago

Post by bernhardw on Probleme mit MC_HALT_SML und MC_STOP_SML ^{CODESYS Forge talk (Post)}
Hallo … ich verwende: SoftMotionLight im Positions-Mode Ethercat-Bus Servoverstärker: Metronix BL4104-C . MC_HALT_SML funktioniert nicht zuverlässig (Achse fährt manchmal zu weit oder bis zum Softwareschalter) Ich habe festgestellt, dass intern beim Aufruf von Positions- auf Velocity-Mode umgeschaltet wird - und dann wird wahrscheinlich intern auf Drehzahl 0 abgeregelt. Kennt jemand dieses Problem? – der Wechsel der Betriebsart ja ist nicht verzögerungsfrei! MC_STOP_SML Der Baustein hat keinen Eingangsparameter "Deceleration" Die Achse stoppt und bleibt im Positions-Mode. Aber die Verzögerung ist nicht wie beschrieben: nicht "Objekt 6085h: quick_stop_deceleration" - sondern "Objekt 6084h: profile_deceleration" - aus zuvor aufgerufenem MC_MOVE_ABSOLUTE_SML Ich wäre dankbar für jeden Hinweis Gruß Bernhard
Last updated: 2024-08-05

Post by snhatton on Running webvisu with Codesys Control Win V3 in Simulation Mode ^{CODESYS Forge talk (Post)}
Yes, you can use the CODESYS ControlWin V3 Soft PLC. However, if simulation is enabled on the device this will disable all communication, so you need to turn off simulation to view the visualization in a web browser. In simulation mode, all IO and communication is disabled for standalone testing. In addition, make sure to set the start visualization in the WebVisu object in the application tree. I hope this helps!
Last updated: 2023-12-04

Post by totorovic on Softmotion not working with simulation mode ^{CODESYS Forge talk (Post)}
Good morning, I think that the mode Simulation does not support the Softmotion functionnality because it runs the CODESYS process with normal priority wich is not a good thing for real-time behavior. If you want to test your PLC project, please use a Codesys Control Softmotion (and your computer must have the Ethercat driver installed) or much easier, download your code into the C6 Smart. BR
Last updated: 2024-05-13

Post by aliazzz on Runtime licenses not detected => DEMO Mode 2hour ^{CODESYS Forge talk (Post)}
Hi! After upgrading all my licensed runtimes to V4.14.0.0 (= RaspberryPi SL, LinuxSL and ControlWin x64 SL) I found out via the logfiles they all defaulted back into DEMO mode while all runtimes have a USB dongle inserted. So, my main question is how I can get the Dongle license detected? I use License Server 4.14.0.0 and Edge Gateway 4.14.0.0 on all platforms Any suggestions are welcome.
Last updated: 2024-12-15

Sort by relevance or date