Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
I have now conducted some tests. The problem occurs when the Python script establishes an OPCUA connection, even if I only establish the connection without reading or writing any data. Is there another way to exchange data between Python and CODESYS without having to put in a lot of effort?
Last updated: 2024-06-24

Post by gseidel on SMC_ERROR SMC_CGR_INVALID_POSPERIOD ^{CODESYS Forge talk (Post)}
Hi blitz, that usually means that the modulo period, when converted to increments, is larger than 2^31. (The bus bandwidth is usually 2^32.) What is your "technical unit", do you program in angular degrees? And what is the modulo period? If you want you can post the drive configuration (screen shot of the "General" and "Scaling/Mapping" page). Best regards, Georg
Last updated: 2025-12-16

Post by davidbo on Two licenses have to be installed forgot to enable one license ^{CODESYS Forge talk (Post)}
I have to install "Basic M" and "Visualization M", but it seems that during installation of "Basic M" you have to enable "Visualization S" I assume if you here after want to install my "Visualization M". And I forgot to enable "Visualization S" How do I fix that?
Last updated: 2026-02-02

Comments in arrays and assigning RST coil's to 600 outputs ^{CODESYS Forge talk (Thread)}
Comments in arrays and assigning RST coil's to 600 outputs
Last updated: 2023-08-31

How to use MC_Home and Configure Task ^{CODESYS Forge talk (Thread)}
How to use MC_Home and Configure Task
Last updated: 2018-04-20

PFC 200 memory gets full and hangs ^{CODESYS Forge talk (Thread)}
PFC 200 memory gets full and hangs
Last updated: 2020-04-05

General question about Codesys and control RTE ^{CODESYS Forge talk (Thread)}
General question about Codesys and control RTE
Last updated: 2020-01-27

A few quick Ethernet/IP and ModBus questions ^{CODESYS Forge talk (Thread)}
A few quick Ethernet/IP and ModBus questions
Last updated: 2021-02-22

raspberry pi B+ GPIO 5 and 6 always TRUE ^{CODESYS Forge talk (Thread)}
raspberry pi B+ GPIO 5 and 6 always TRUE
Last updated: 2016-10-07

Scaling Problems mit Visualization and iPAD Pro Safari ^{CODESYS Forge talk (Thread)}
Scaling Problems mit Visualization and iPAD Pro Safari
Last updated: 2022-06-01

Running and A-axis smoothly at constant velocity ^{CODESYS Forge talk (Thread)}
Running and A-axis smoothly at constant velocity
Last updated: 2016-01-22

Using it with beckhoff CX9020 and getting PLC disconnections ^{CODESYS Forge talk (Thread)}
Using it with beckhoff CX9020 and getting PLC disconnections
Last updated: 2013-09-09

Low latency communication between raspberry pi and arduino ^{CODESYS Forge talk (Thread)}
Low latency communication between raspberry pi and arduino
Last updated: 2019-06-09

Did a library update and now can't open project ^{CODESYS Forge talk (Thread)}
Did a library update and now can't open project
Last updated: 2023-09-25

Threads and TID created by CODESYSControl Win V3 ^{CODESYS Forge talk (Thread)}
Threads and TID created by CODESYSControl Win V3
Last updated: 2023-10-02

How to switch between dynamic IP address and dynamic? ^{CODESYS Forge talk (Thread)}
How to switch between dynamic IP address and dynamic?
Last updated: 2023-11-08

Codesys Raspberry Runtime 4.10.0.0 and RSM Utility 3.5.19.0 ^{CODESYS Forge talk (Thread)}
Codesys Raspberry Runtime 4.10.0.0 and RSM Utility 3.5.19.0
Last updated: 2023-11-21

About byte swap and convert into 16 bits ^{CODESYS Forge talk (Thread)}
About byte swap and convert into 16 bits
Last updated: 2023-12-04

ScriptEngine - execute "Export -> Bootproject and firmware (SD Card)" from python ^{CODESYS Forge talk (Thread)}
ScriptEngine - execute "Export -> Bootproject and firmware (SD Card)" from python
Last updated: 2024-07-05

Codesys and CANopen manager sensors with same NodeID ^{CODESYS Forge talk (Thread)}
Codesys and CANopen manager sensors with same NodeID
Last updated: 2024-07-22

Ruspberry PI and working with profinet slave. ^{CODESYS Forge talk (Thread)}
Ruspberry PI and working with profinet slave.
Last updated: 2024-07-30

CNC Jumps G20 - SMC_NCInterpreter and long time to process ^{CODESYS Forge talk (Thread)}
CNC Jumps G20 - SMC_NCInterpreter and long time to process
Last updated: 2024-08-03

Communication between PLC and HMI- sending DUT data ^{CODESYS Forge talk (Thread)}
Communication between PLC and HMI- sending DUT data
Last updated: 2024-08-23

Communication between PLC and HMI- sending DUT data ^{CODESYS Forge talk (Thread)}
Communication between PLC and HMI- sending DUT data
Last updated: 2024-08-23

Communication between PLC and HMI- sending DUT data ^{CODESYS Forge talk (Thread)}
Communication between PLC and HMI- sending DUT data
Last updated: 2024-08-23

Sort by relevance or date