Post by ofey on OPC server crash ^{CODESYS Forge talk (Post)}
Hi! I repeatly encounter a crash of the OPC server, which forces a reboot of the controller with frequent connect/disconnect to the server. Have any of you encountered this before? And is it a workaround? ie. deny that particular client connection by timeout or similar instead of crashing the PLC? This is during a development phase of the user interface. Up to 3 others connect/disconnect frequently to test their code. It is a bit troublesome of the PLC crashes several times a day because of this :( I greatly appreciate all comments. I hope it exists a fix for this, or something that hinders the crash. I attached the logfile for the crash
Last updated: 2024-11-26

Post by cihangur on OpC UA server on Raspberry Pi 64 SL runtime ^{CODESYS Forge talk (Post)}
After my tests, I noticed two issues. 1- WinCC disconnects the connection after receiving the GetEndPointResponse message from CoDeSys. (I found it with UAExpert and Wireshark.) 2- It establishes a connection despite waiting for a while on the network with DNS. As a result of this information: I solved the problem by adding the line "193.193.193.150 t9pac" to the C:\Windows\System32\Drivers\etc\hosts file and making Windows accept messages coming from the IP number 193.193.193.150 as coming from t9pac. (t9pac is the name of my PLC running CoDeSys.) If there is a setting that will allow CoDeSys OPC UA to respond to GetEndPointRequest with its IP address, this problem will not occur.
Last updated: 2024-12-12

Post by mkintegration on Reading Absolute Encoder Position From Yasakawa Drive ^{CODESYS Forge talk (Post)}
I am looking to read in the absolute position of a yaskawa servo drive Sigma 7 that is using absolute encoder. It looks like yaskawa outputs this across there CN1 I/O connecter and during operation just outputs encoder pulses. But at boot up transmits the Multiturn data position and the Position within one rotation (pulse train) on two different wires. Once the drives are enabled it just uses incremental pulses. Does any one have experience with what IEC blocks to use to read this information in. I attached the Yaskawa Manual section that talks about the format.
Last updated: 2025-02-26

Post by mkintegration on Reading Absolute Encoder Position From Yasakawa Drive ^{CODESYS Forge talk (Post)}
I am looking to read in the absolute position of a yaskawa servo drive Sigma 7 that is using absolute encoder. It looks like yaskawa outputs this across there CN1 I/O connecter and during operation just outputs encoder pulses. But at boot up transmits the Multiturn data position and the Position within one rotation (pulse train) on two different wires. Once the drives are enabled it just uses incremental pulses. Does any one have experience with what IEC blocks to use to read this information in. I attached the Yaskawa Manual section that talks about the format.
Last updated: 2025-02-26

Post by struccc on Multiple applications on one device sharing variables. ^{CODESYS Forge talk (Post)}
I don't exactly recall where (I think some release notes), but I read the information that this multiple application / sub application feature is to be discontinued. Please, correct me, if I'm not right about this I am a bit sad about that - I was using that feature with more or less success. However I understand the reason behind the change: it introduces huge complexity, especially when dealing with multicore and safety support... AS I understand, it's to be replaced with the new virtual plc architecture, and standard ways for synchronizing / sharing data... So, for now the "Add application" context menu item was removed, but behind the scene it is still supported... Hint: if you still want to experiment with it, might try copy-paste things within the PLCLogic tree...
Last updated: 2025-02-28

Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by rossanoparis on Internal Error (ARM): Unsupported conversion! With new version v3.5 SP21 ^{CODESYS Forge talk (Post)}
I have updated CODESYS development tool to the version v3.5 SP21 (64bit) The previous version was v3.5.20.40 Compiling an existing application with the new evelopment tool I get the following error. kunbusiodrvrevpibridge, 1.4.1.0 (kunbus gmbh): IoDrvScanModules [IoDrvRevPiBridge](Line 51, Column 1 (Impl)): Internal Error (ARM): Unsupported conversion! This error was not reported in the previous compiler version and is now highlighted in a third-party library, which I cannot change or modify. The error is due to the following conversion: m_udiError := TO_UDINT(excCode); . The excCode variable is a system type, declared as shown below, and should be converted to a UDINT excCode : __SYSTEM.ExceptionCode; m_udiError: UDINT; . I would appreciate it if someone could provide feedback on this issue.
Last updated: 2025-04-15

Post by andrej on Creating, using an external Function. ^{CODESYS Forge talk (Post)}
Hello all, I would like to create a simple which runs directly on Control WinV3 x64 3.5.21.0 For this purpose I created a simple dll myAdder.dll in Cpp // MyAdder.cpp // cl /LD /EHsc MyAdder.cpp /Fe:MyAdder.dll #include <windows.h> extern "C" __declspec(dllexport) int __cdecl CmpMyAdder_Add(int a, int b) { return a + b; } I added the dll in the respective folder. Furthermore I "registred" the dll in the CODESYSControl.cfg. However, when I want to use the library I get the error message: Uresolved reference: *'CMPMYADDERADD' * Can you give me a hint what step I missed or where I need to declare the dll, such that the dll resp. the reference can be resolved. Many thanks and kind regards
Last updated: 2025-04-18

Post by alex2 on Error Highlighting Not Working in CODESYS v3.5 SP10 on Windows 11 ^{CODESYS Forge talk (Post)}
Hello everyone, I'm currently using CODESYS v3.5 SP10 on Windows 11, and I've noticed that syntax errors are not automatically underlined in red as they normally should be. Is there a specific setting that needs to be enabled for this feature to work? If so, could you please let me know where to find it? I’ve already tried uninstalling and reinstalling CODESYS, but that didn’t resolve the issue. Also, i have a teammate who have exactly the same computer as me and he didnt encounter any issue. Thank you in advance for your help!
Last updated: 2025-05-13

Post by durallymax on Dynamical scaling of bar graph without the bar itself ^{CODESYS Forge talk (Post)}
I'm a fan of the analog indicators from ISA101. To recreate these, I use a number of rectangles that are dynamically sized and colored based on the input configuration. To keep it standard and easy, everything is built around 100px height. Then when instantiated in a frame, it can be resized as needed with the math remaining the same. The math logic is in a METHOD called by the rear most rectangle. These indicators do not use a "filling" bar graph, rather a fixed bar graph with a carrot to track the current value.
Last updated: 2025-06-06

Post by kareem-pt on Velocity is too low even though correct value is reported ^{CODESYS Forge talk (Post)}
Hello, I'm playing around with a single axis. I've setup scaling and set the drive to move 360 degrees in the commissioning tab. The axis does move 360 degrees, but it moves much slower than the 360 degrees per second that I set for the velocity. It seems to be about 3 times slower (taking about 3 seconds instead of 1). This is despite the set and actual velocity both being displayed as 360. The acceleration, deceleration and jerk are all set to very high values. I'm just running this on my PC, using demo mode (no license purchased yet). I've attached a video showing the problem. Does anyone know what the problem could be? Thanks
Last updated: 2025-06-06

Post by pernockham on AC Persistence - values are not read from file during start? ^{CODESYS Forge talk (Post)}
I swear I tested this like 20 times yesterday without success. Repeated it today and it works. Maybe the system needed a "real" power reboot? To note. To make a manual edit of a variable I tried some different approaches this is what worked for me. "system/online edited" gvl_var.example_variable REAL:F16#2FFB334H-4 767.7 "manually edited" (with runtime stopped followed by a "cold start" to read from file) gvl_var.example_variable REAL:790.1 (the system will use the manual value but will not set an equivalent "hex" value until next online edit/write cycle)
Last updated: 2025-09-03

Post by sean-barton on Function block method default arguments ^{CODESYS Forge talk (Post)}
I have default arguments specified for function block methods but when calling a method, an error is produced requiring me to supply all the arguments despite there being default values. According to the online documentation, under section "Calling a Method" and subsection "argument passing" of the following link: https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_obj_method.html "Passing an argument for an input ... can be omitted ... for which a default or initial value was specified in the declaration..." I have found this to be the case for all Codesys IDEs I've used, 3.5.11, 3.5.16, 3.5.17, 3.5.19. Am I missing something?
Last updated: 2023-12-21

Post by royw on Profinet library for C# ^{CODESYS Forge talk (Post)}
Hi, I don't know if I'm in the right place or if it's even possible... I'm looking for a way to address a Profinet device with Record Read and Write from my own PC. I actually only need very few commands to configure our device. This means setting the MAC address and a serial number. We would like to do this from a C# program. Now we are looking for a library or something similar. Since you can do it from Codesys, I thought there might be a DLL or something similar that you could use for this. As I said, we don't want real-time queries of the cyclic data but only record read/write. Does anyone have any helpful hint? Thanks in advance
Last updated: 2023-12-22

Post by dhumphries on Ethernet/IP Issue ^{CODESYS Forge talk (Post)}
Make sure the O->T and T->O bytes required by the remote device match the configuration in Codesys. Most of the EDS files I've imported have not worked by default. See the attached images for the connections and assemblies tabs. Note that the connections are in Bytes and the assemblies are in bits, you have to have enough bits to equal the bytes. Either mismatch will give a red/orange triangle. Page 343 of the manual (assuming the STF10-IP is an applied motion microstep driver) has some recommended connection settings, you should be able to confirm the input and output bits somehow, some devices have a web GUI, some require a software tool.
Last updated: 2024-02-03

Post by alexgooi on Is it possible in the log to see previous shutdown ^{CODESYS Forge talk (Post)}
Hi DavidBo, In general Codesys is used to control equipment and an exception is the worst thing that can happen in your installation. If you cannot prevent the exception from triggering, you could implement a Try catch statement, with this solution your controller keeps on running and you are able to handle the exception. __TRY //This statement will trigger an exception Result := 4/0; __CATCH(exc) //Handle the exception HandleException(exc, strExceptionText => strExceptionText); // From the Codesys help file //Create a log file //-------------------------------------------------------- __ENDTRY What you also could do is implement implicit checks, these functions cover most of the exceptions (like dividing by zero) See picture But in general avoid a complete controller shutdown!
Last updated: 2024-02-09

Post by dkugler on Toggling Visualizations using HMI Physical Buttons ^{CODESYS Forge talk (Post)}
the magic option is named "Use CurrentVisu variable" activate this option in the Visualization Manager an have a look: https://help.codesys.com/webapp/_visu_obj_manager;product=core_visualization;version=3.5.14.0 if your button is pressed, "feed" the string varable VisuElems.CurrentVisu := 'visu1'; with the correct name of the depending visu. alternative: place a frame element at a empty main visu, konfigure all visus to be shown by this frame. With setting the switching variable of the frame to the index value of the depending visu, it will switch to it. Advantage: the visu names are not hardcoded as string in the ladder lodgic. Good luck! Hint: If you have multiple VisuClients(Target, WebVisu,...) all will show the same visu. Independent switching is much more difficult, but there is a example from codesys.
Last updated: 2024-02-13

Post by dhumphries on Toggling Visualizations using HMI Physical Buttons ^{CODESYS Forge talk (Post)}
Nothing wrong with ladder, in a lot of applications it is simpler than ST or CFC, you're a lot less likely to have syntax issues in a ladder diagram than in structured text as long as you stick with traditional ladder elements. Your attempt was almost valid, but you tried to change the currentvisu variable using a blend of structured text and ladder, which isn't allowed. You need to use the MOVE operator and define the visualization name as a string on the input side and the visuelems.currentvisu as the target on the output side.
Last updated: 2024-02-28

Post by mp9876 on Device logon problem following fresh install ^{CODESYS Forge talk (Post)}
Yes it had been the case I believe as I have seen that message regarding they were not the same. I had update the device though to match them and that still did not fix the problem. I gotta say I wanted to get out of that situation and attempted a lot of things and then I did two things at the same time that fixed my problem: Wiped the 64 bit version and installed the 32 bit version Installed latest SP20 I wish I knew which one of these actions fixed the problem but now I gotta catch up on this IDE learning; it's been quite a learning experience I have to say! Thank you very much for your time and advice; much appreciated!
Last updated: 2024-03-19

Post by ragarcia on Error while using Codesys SP19 Patch 4 on Windows 11 ^{CODESYS Forge talk (Post)}
Hello everyone, I just installed Codesys SP19 Patch 4 on Windows 11 and every time I open Codesys I get an error that says (Attached image): 'One or more issues ocurred with the current versio profile. Please contact the vendor to resolve these problems. The plug-in {....} (Exactly 4.15.0.0) is required by the current version profile., but has not been installed. It is highly recommended that the tools is terminated. Do you wanto to terminate now?' I cannot install any package since I get this error everytime I open or try to install any package. Can someone help me please, thanks in advanced
Last updated: 2024-03-26

Post by r-niedermayer on Issue with WebVisu on Raspberry PI ^{CODESYS Forge talk (Post)}
Regarding to your application: When clicking in the web visualization, the boolean variable will be tapped for both buttons. The LED in the web visualization lights up as long as the variable is true The used variables should come from the GVL, ad/or thePLC_Prg. We see no difference or problem in both projects: You have created a visuelement Push button a a tapper, that is supposed to control the variable in this way as expected. This is also reflected (switching Bool from false to true) in the program code, as well as in the (GVL declared) variables. Wherever the misunderstanding comes from: no, this is not memory or license related. Our best guess: it is probably more of an applicative/conceptual implementation.
Last updated: 2024-04-11

Post by westcountryewe on Persistence Variables missing and DO NOT retain from Persistence Channel when using Boot Application ^{CODESYS Forge talk (Post)}
We've been experiencing an issue through SP18, SP19 and now SP20 where the Persistence Variables do not retain if we upload our program via a Boot Application. If we use the exact same program, and perform a Direct Upload via the Laptop and Ethernet connection, the Persistence Variables work exactly as expected. I have submitted 2 bug support tickets but I haven't had a response back from Codesys. Has anybody experienced the same issues and discovered a workaround? We have a requirement to utilise the Boot Application method because of logistical restrictions of being able to get out to every site, so at the moment it's a bit restriction.
Last updated: 2024-05-15

Post by adaffern on Runtime on Raspberry pi5 stops after 15 seconds ^{CODESYS Forge talk (Post)}
Hi Guys, I'm new to CODESYS on the pi and I'm struggling to get it working. My issue is that the runtime keeps stopping after approximately 15 seconds. I have installed the runtime package 4.11.0.0 on the pi, trying on both a 64 bit and 32 bit OS. Looking at old forums it all references the 4B and the fact they used 32 bit Debian bullseye (the last version of raspberry pi os) however the pi 5 doesn't offer this version when I try select it in the imager. Has anyone managed to get running using the pi 5? Any help would be greatly appreciated. Thanks, Adam
Last updated: 2024-06-10

Post by fajean on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
4.11 appears to solve the problem. Thanks for your help. I had first installed the 64-bit version of RPiOS, but looking at various posts and the product's page on the store which only lists 32-bit compatibility, I downgraded to the 32-bit version. I did this before trying 4.11, and it did not solve the problem. Thus my working system is 32-bit, and I am wondering if I can go back to 64-bit or not. An 64-bit OS is not listed as compatible on the store's web page, but when installing there actually is a 64-bit version listed (automatically chosen when installing on 64-bit, but otherwise greyed out). Is 64-bit supported and the website is out-of-date, or is that some kind of work-in-progress?
Last updated: 2024-06-13

Post by kthomas on Cant login to Rpi4 but can see it in codesys communications settings. ^{CODESYS Forge talk (Post)}
I have been struggling for over a week to program my rapspberry pi 4 with codesys. I purchased the license. I installed the runtime and the gateway, and I can see the pi in the communication settings. But cannot log in. I have checked the status of the pi with sudo systemctl status codesyscontrol and it is running. I have enabled traffic to and from the pi with iptables and checked the logs and all looks good. I just cannot connect through the codesys ide. Can anyone help me before I lose my mind?
Last updated: 2024-06-22

Sort by relevance or date