Post by mp9876 on Problems with simulation in Window 10 ^{CODESYS Forge talk (Post)}
Hi Eschwellinger, sorry for so late reply but I found a solution back then; uninstall completely Codesys V3x64 and re-installed Codesys V3x32 to properly note the password I created and everything went ok. thank you for your suggestion and have a good day/evening Mike
Last updated: 2024-05-30

Post by davidbo on Toradex and CODESYS and licensing ^{CODESYS Forge talk (Post)}
I am evaluating a Toradex product for use with CODESYS. Toradex and CODESYS are partners, but using "CODESYS Virtual Control for Linux ARM64 SL" together with a carrier board "Verdin mallow" However it doesn't seem to be a soft container for licenses. So how do I install a license
Last updated: 2025-10-20

Post by navan on License Reset Request – CODESYS Control Win V3 Standard L ^{CODESYS Forge talk (Post)}
Dear CODESYS Support Team, My IPC hardware failed and was replaced. The CODESYS Control Win V3 Standard L license now shows “Activation Invalid” in CodeMeter Control Center. Please reset or reissue the license to my new IPC. Details: Product: CODESYS Control Win V3 Standard L 32 bit Version: 3.5.20.10 Ticket : Xxxx-xxxx-xxxx-KJE4 New Container ID: (130-......837) Thank you,
Last updated: 2025-10-23

Post by kalmeyer on Stepper motor control with (SM_Drive_RaspStepper_direct) ^{CODESYS Forge talk (Post)}
Hi Helpers I'm trying to work with stepper motor on Rasp 5 for the first time. So I'm pretty new.😥here. I've used: https://forge.codesys.com/drv/sm3raspistepper/home/Home/ but I get the following error when I insert. I also get 6 errors when I "rebuilder" after installering "SM_Drive_RaspStepper_direct" from the tree. Hope there is help for me. Thanks in advance /Klaus
Last updated: 2025-11-04

Post by aniket-b on Scara3 kinematic robot error ^{CODESYS Forge talk (Post)}
Here I have attached the task monitor data. What is very weird is that I am using MC__MoveDirectAbsolute FB, when I choose Vel/ACC/Jerk Factor to 1.0 it run fine. It ran 10 hours without the issue. But I get the error randomly when I use factor as 0.5
Last updated: 2025-12-29

Post by transmin01 on PCAN serial "No CAN driver found" ^{CODESYS Forge talk (Post)}
Hi, I am using a PCAN mini CAN board which has the Windows drivers installed on the target PLC. PCAN board can be seen in device manager. However, I am getting "No CAN driver found" error. I have read the post https://forge.codesys.com/forge/talk/CODESYS-V2/thread/44aae19318/ and have uncommented the CmpPCANBasicDrv driver in the CodesysControl.cfg file in development PC and have copied it to the target PC. Current CodesysControl.cfg file attached. Is there anything else I am missing? Regards
Last updated: 2023-09-14

Post by damian177 on Codesys and SMS in RPi ^{CODESYS Forge talk (Post)}
Hi, I try use IIoT library to send and receive SMS by Raspbery PI and Codesys. I installed IIoT package and added the SMS library, But something is wrong, when I init communication it doesn't work, When I sniffer my communication (AT commands) beetwen RS232 RaspberryPi and my GSM modem I have only below commands: AT+CMEE=1 OK AT+CPIN? +CPIN: READY Anyone have idea what can be wrong ?
Last updated: 2023-09-28

Post by andre-luis on Check if Codesys runtime is on 'Running' or 'Stopped' state? ^{CODESYS Forge talk (Post)}
Just to share, for those who as me are seeking for this and had found no information anywhere in this World: Every time I stop/start the PLC runtime ( turning into 'Stopped' or 'Running' state ) the 'CODESYSControlService' appears at the Taskmanager list, which could suggest a straight correlation. I was expecting a clever solution, but this one solves for while.
Last updated: 2024-07-02

Post by anuj9326 on OPC-UA Client connection, Linux SL /Raspberry Pi ^{CODESYS Forge talk (Post)}
hello edwin i have did the same and i could connect the opc-ua server but i dont see anything in the resources tree, in the application i linked my variables to the symbol configuration but i dont see that in the uaexpert. if i use the same application with a non linux system i can get those variables values and see the complete tree structure. What could be the problem ?
Last updated: 2024-08-21

Post by anuj9326 on OPC-UA Client connection, Linux SL /Raspberry Pi ^{CODESYS Forge talk (Post)}
hello edwin i have did the same and i could connect the opc-ua server but i dont see anything in the resources tree, in the application i linked my variables to the symbol configuration but i dont see that in the uaexpert. if i use the same application with a non linux system i can get those variables values and see the complete tree structure. What could be the problem ?
Last updated: 2024-08-21

Post by pradeepradha on Update Raspberry Pi option is missing under Tools menu ^{CODESYS Forge talk (Post)}
Hello, the option to update Rasberry Pi from under the Tools menu is missing in my installation. Currently I have the build 3.15.19.50, along with the Pi package 4.11.0.0. But the same problem is observed even with the latest build and Pi packages. I have tried clean install with both the versions but cannot solve the issue. I never faced this on Windows 10, but now the new PCs are with Windows 11 - this is the only difference. How can I solve this problem?
Last updated: 2024-09-02

Post by dkugler on EThercat Dynamic configuration ^{CODESYS Forge talk (Post)}
I can confirm that at my 4ms EtherCAT Master the frames per second is equal at round about 500 with Codesys SP19. The same program at SP16 it was at 380-430 f/sec. for me it will be interesting too, whats the reason is for this high frame count/sec? I havn't had the time to use a paket sniffer and analyse all the frames. I can't help with your other questions, sorry.
Last updated: 2024-09-19

Post by mini-developer on Profinet Exor connection drop ^{CODESYS Forge talk (Post)}
Hello, I have a Exor HMI with 2 seperatred ETH interface's. It is Configured as PN Master on ETH interface 1 and the IO's are working, as long as the development PC is connected to the ETH 0 interface. When the PC is disconnected, the PN communication drops and a reconnection is started. I installed the newest device description for Codesys and Firmware for the Panel. The IO Gateway is from Weidmueller What could cause the Problem?
Last updated: 2024-10-16

Post by sebastianrapi on Bibliothek: floatingpointutils ^{CODESYS Forge talk (Post)}
Hallo Zusammen, ich versuche die Bibliothek FloatingPointUtils.compiled-library-v3 zu benutzen. leider kommt dabei folgende Fehlermeldung: Kein Quellcode für dieses Objekt... (siehe Anhang) Wie kann ich diese Bib einbinden? Kann ich diese irgendwo herunterladen? Mein Ziel ist es ein DWORD (float) in ein REAL umzuwandeln. ICh hoffe, dass ich dies mit der Funktion HexStrToReal machen kann. So wie hier: https://gregstoll.com/~gregstoll/floattohex/ convert to float... Oder gibt es bei Codesys einen anderen Weg? Ich verwende v3.5 SP20 Patch 1 + (32Bit) Grüße Sebastian
Last updated: 2024-10-17

Post by vincentger on using ADS1115 ^{CODESYS Forge talk (Post)}
Any reason the ADS1115 wouldnt work with SP20.1 and Runtime 10.0.0.0 on the Raspberry Pi . Using Bullseye or Buster i run into the same issue: Libary and integration works in general as described above BUT i am seeing "bleeding" between the analog inputs . Specifically consecutive ones: So sometimes the raw from AI1 shows on AI2, AI2 on AI3, .. AI4 on AI1. Even with filtering i cant smoothen that out properly and i feel like something is wrong. Almost like the bus is stumbling over itself, or the request from Codesys to the device.
Last updated: 2024-10-28

Post by askic on PLC error log help ^{CODESYS Forge talk (Post)}
Hello, I'm using Codesys 3.5.20.0 version and I noticed that even with the most basic standard project create, there are error messages like shown in the acttached picture. The similar questions are already asked here on the CODESYS Forge Talk, but remained unanswered. Exact screenshot is attached, but essentially I would like to know which component in the Codesys has CmpID = 0x00000019 and what this Timeout means?
Last updated: 2025-01-10

Post by andre-luis on Device diagnosis ( EtherCAT IO card ) ^{CODESYS Forge talk (Post)}
Hi @TimvH, In the meantime, I did some experiments and could find a way to achieve similar result. I made some tests, removing the last card from the array, seeing the change on status. PROGRAM P_IOS_STATUSES VAR devStateInput : DEVICE_STATE; devStateOutput : DEVICE_STATE; devStateEncoder : DEVICE_STATE; END_VAR devStateInput := IoConfig_Globals.EL1819.GetDeviceState(); devStateOutput := IoConfig_Globals.EL2809.GetDeviceState(); devStateEncoder := IoConfig_Globals.EL5151.GetDeviceState(); GVL.bInputCardOK := ( devStateInput = DEVICE_STATE.RUNNING ); GVL.bOutputCardOK := ( devStateOutput = DEVICE_STATE.RUNNING ); GVL.bEncoderCardOK := ( devStateEncoder = DEVICE_STATE.RUNNING ); Many thanks for your quick and extensive reply.
Last updated: 2025-02-06

Post by josul on Web Client HTTPS Communication Issue ^{CODESYS Forge talk (Post)}
Thank you for the suggestion. There is a certificate created in the quarantine directory relating to the URL used for the webclient FB. This certificate should have been valid as it was created only the week before this problem was encountered. I investigated a separate location using the same https URL and it has 2 certificates in the same quarantine directory, 1 is created almost 200 days ago, the other over 100 days ago. There have been no similar problems encountered with these certs or https at all.
Last updated: 2025-06-09

Post by jari-koivuluoma on Finding out exception code position ^{CODESYS Forge talk (Post)}
Is it possible to find out the code position from where the exception originated using information from this log entry? 2025-07-02T13:56:19Z, 0x00000011, 8, 81, 3, #### Exception: *EXCEPTION* [<excpt>AccessViolation</excpt>] occurred: App=[<app>Application</app>], Task=[<task>Task</task>] 2025-07-02T13:56:19Z, 0x00000011, 8, 81, 3, #### Exception: *SOURCEPOSITION* App=[<app>Application</app>] area=<area>2</area>, offset=<off>13349868</off>
Last updated: 2025-07-02

Post by wollvieh on Problem while updating to new runtime 4.11.0.0 ^{CODESYS Forge talk (Post)}
okay, no ideas. So i made a new fresh image for the raspberry, so far,so good. Licensing the new image was no problem. And, after having trouble while read write files on the raspberry pi, i found the solution for these file operations with the Variable ForceIecFilePath in the CODESYSControl.cfg file. Some people had that issue discussed in that thread : https://forge.codesys.com/forge/talk/Deutsch/thread/d2df08e587/
Last updated: 2024-03-18

Post by hoatran on Use third party actuator with IO-Link Master (IFM) ^{CODESYS Forge talk (Post)}
The generic sensor FB is for controlling the sensor via its cyclic input (PDI) and output (PDO). In this case, ifm raw cyclic input and output data are WORDs (16 bits total) The PDO data from the Buerkert unit are SINT (8 bits) In this case, I would use the unpackword fb from the CAA memory library to unpack the valve feed back value into the appropriate location.
Last updated: 2024-04-23

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
All Sensors from the OneWire Master are assigned already to a seperate task with low prio (26) that runs with 1s cycle time. My EtherCat Task is running with Prio 1. It all works fine, until I adjust the CODESYScontrol.cfg or the CODESYScontrol_Usr.cfg files so that it supports a 2nd OneWire Master in the Codeys Runtime. If I change something in this config file and reboot my EtherCat Master stops working.
Last updated: 2025-10-19

Post by gatewail0 on Digital Clock ^{CODESYS Forge talk (Post)}
You can definitely pull the actual system time into CODESYS without too much trouble. Take a look at the SysTimeRtc or SysTime library—both let you read the current date and time from the Raspberry Pi. You can call SysTimeRtcGet() or SysTimeGetTime() in your PLC code and then format the hours, minutes, and seconds into variables that feed your 7-segment visualization. Once you’ve mapped those values, your Visu display will update automatically each cycle. It’s a pretty common approach for clocks in CODESYS, so you should be able to get it working quickly. golf hit
Last updated: 2025-12-04

Post by damian177 on Codesys and SMS in RPi ^{CODESYS Forge talk (Post)}
I tried initialize my GSM modem by write simple application in C, and GSM modem works, below used AT commands: AtChat: T : "AT" AtChat: F : "OK" AtChat: T : "AT+CMEE=1" AtChat: F : "OK" AtChat: T : "AT+CMGF=0" AtChat: F : "OK" AtChat: T : "AT+CGMI" AtChat: F : "WH_Ltd" AtChat: F : "WH_GM35" AtChat: F : "Revision: RDA BV5" AtChat: F : "OK" AtChat: T : "AT+CGMM" AtChat: F : "WH_GM35" AtChat: F : "OK" AtChat: T : "AT+CGMR" AtChat: F : "Revision: GM35-D_B5_R05_A01_D170914" AtChat: F : "OK" AtChat: T : "AT+CGSN" AtChat: F : "868221045990218" AtChat: F : "OK" AtChat: T : "AT+CNMI=2,1,0,1,0" AtChat: F : "OK" AtChat: T : "AT+CLIP=1" AtChat: F : "OK" AtChat: T : "AT+COPS?" AtChat: F : "+COPS: 0,2,\"26002\"" AtChat: F : "OK" operator name: "26002" AtChat: T : "AT+CREG?" AtChat: F : "+CREG: 1,1" AtChat: F : "OK" at+creg Modem is initialized I do not understand why Codesys SMS library send AT+CPIN? command ?
Last updated: 2023-09-29

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Ok, so i made some tests in the meantime and i have some conclusions. It apears that the enable bit is activated only when a motion function is executed. I implemented a very simple program with MC_Power and MC_Jog. If i enable everything on MC_Power, the enable GPIO pin stays off. However, as soon as the MC_Jog function is used the enable GPIO pin turns ON and remains ON. In version 0.0.0.4 this is not happening. The GPIO enable pin turns on or off when the MC_Power is enabled or disabled. From this behaviour i understand that in version 0.0.0.6 the GPIO enable bit is activated together with pulse and dir pins when motion starts. When motion stops, enable bit remains with the last state (on in this case) and you cannot turn it off for example. For me this bit is useful because i can turn on and off the stepper drive with MC_Power function. Now i can turn it on, but never off.
Last updated: 2025-04-04

Sort by relevance or date