Post by gunstr on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
I now tried to install 4.17.0.0 on a fully clean installations: A brand new RPi 4B Install latest Raspberry Pi OS Lite, Release date 13 May 2025, 64bit run sudo apt update && sudo apt full-upgrade When asked - Select to install the updated version of '/etc/initramfs-tools/initramfs.conf' Install CODESYS Control for Raspberry Pi SL. version 4.17.0.0 Log output: [INFORMATION] Connected successfully! [INFORMATION] Successfully connected to target (192.168.0.197) [WARNING] No supported container engine found on device. You have to install a supported container engine to use Virtual Control. Please contact the Administrator of the device. [WARNING] Error detecting container architecture [INFORMATION] Finished reading device information [ERROR] Error output: /var/lib/dpkg/info/codesyscontrol.postinst: 88: check_legacy_extensionapi_folder: not found [INFORMATION] Standard output: Selecting previously unselected package codesyscontrol. [INFORMATION] Standard output: (Reading database ... 76772 files and directories currently installed.) [INFORMATION] Standard output: Preparing to unpack .../codesyscontrol_raspberry_4.17.0.0_all.deb ... [INFORMATION] Standard output: Unpacking codesyscontrol (4.17.0.0) ... [INFORMATION] Standard output: Setting up codesyscontrol (4.17.0.0) ... [INFORMATION] Standard output: make config rw [INFORMATION] Standard output: set folder permissions [INFORMATION] Standard output: prepare permissions [INFORMATION] Standard output: check legacy extension api folder [INFORMATION] Standard output: create and install daemon [INFORMATION] Standard output: codesyscontrol started [WARNING] Unable to detect Raspberry Pi Architecture. Setting armv6l as default, you can change this through the settings panel. [INFORMATION] Standard output: codesyscontrol stopped [ERROR] Expected exit value of command failed: expected 0, received 1 [WARNING] Error setting the Raspberry Pi Architecture [ERROR] Error installing codesyscontrol If I read the log correctly the control is actually installed but cannot start. I'm running out of ideas how to proceeed now, any suggestions are welcome.
Last updated: 2025-09-03

Post by ryandmg on Web Client (HMI) Disconnects from Webvisu (Weidmuller u-OS) ^{CODESYS Forge talk (Post)}
Thanks So Much for the reply! Were using the Weidmuller UV66-ADV-10-CAP-W The HMI is pointed to the URL which is assigned through u-OS. Basically when you log into the controller's webserver via browser you can view the installed apps. One of which is the Codesys runtime. When you click on that it takes you to the visualization. That corresponding url is what the HMI is looking for. I apologize I don't have that on hand as I'm in the office right now. I don't think I tried connecting using the port you mentioned and https in lieu of the u_OS URL. I can certainly try. Out of the box the u-OS is set for HTTP. Since we're isolated I havent changed that yet. When this has happened while logged on via chrome on my laptop, simply refreshing brings the visualization right back. In the case of the HMI in kiosk mode, we power cycle the HMI to force a reconnect, log back in u-OS and the visualization is back.
Last updated: 2023-09-06

Post by pernockham on Persistence Manager: Config File not found? ^{CODESYS Forge talk (Post)}
Back in november I paused this, but wanted to reattempt using the persistent manager, the behavior is still the same. Most "login attempts" s are stopped with the message "One or more errors occurred" but I have no idea what that error might be. The only clue is this message is presented while the lower left status box says "Generating code...: relocation pou". For clarification. Build/Generate code is successful, no errors. Error appears when I try to download/login (physical or simulation) to a device. I did manage to login (in simulation mode) at one point, but then the error message "PersistenceChannel: Config file not found!". And no persistence files were created. I have done device-tree/reset-orgin also clean/clean all etc. Removed/re-inserted persistance manager. Behaviour is just the same. Removing Persistence Manage and everything is working OK. Is there possibly more info somewhere about the "One or more errors occured"-message?
Last updated: 2025-03-20

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Ok, so i made some tests in the meantime and i have some conclusions. It apears that the enable bit is activated only when a motion function is executed. I implemented a very simple program with MC_Power and MC_Jog. If i enable everything on MC_Power, the enable GPIO pin stays off. However, as soon as the MC_Jog function is used the enable GPIO pin turns ON and remains ON. In version 0.0.0.4 this is not happening. The GPIO enable pin turns on or off when the MC_Power is enabled or disabled. From this behaviour i understand that in version 0.0.0.6 the GPIO enable bit is activated together with pulse and dir pins when motion starts. When motion stops, enable bit remains with the last state (on in this case) and you cannot turn it off for example. For me this bit is useful because i can turn on and off the stepper drive with MC_Power function. Now i can turn it on, but never off.
Last updated: 2025-04-04

Post by gseidel on AXIS_REF_SM3 Error Codes? ^{CODESYS Forge talk (Post)}
Hi SLUCodesys, dwErrorId is a drive specific error number. The drive documentation should be consulted to interpret it. (Note that you should use MC_ReadAxisError to read this error, see https://content.helpme-codesys.com/en/libs/SM3_Basic/Current/SM3_Basic/POUs/Diagnostics/MC_ReadAxisError.html. Accessing the internal variable will result in outdated values if the acis error is not mapped by PDO and is not recommended in general.) uiDriveInterfaceError holds errors of the SoftMotion driver for the drive. It is also an internal variable, not intended for direct access. It is intended for logging, the PLC log will contain the drive interface error, consisting of this number and an error text. My recommendation for handling axis errors in the CODESYS application: 1) Use MC_ReadStatus on the axis to find out whether it is in state Errorstop 2) If in Errorstop, there are two possibilities: an error reported by the drive (MC_ReadAxisError) or an error of the SoftMotion function blocks (output MC_ReadStatus.FBErrorOccured). 3) If there is no drive error, you can use SMC_ReadFBError https://content.helpme-codesys.com/en/libs/SM3_Basic/Current/SM3_Basic/POUs/Diagnostics/FBError/SMC_ReadFBError.html Best regards, Georg
Last updated: 2025-09-24

Post by farren on How to stay in a method until something is finished. ^{CODESYS Forge talk (Post)}
I know I'm thinking about this wrong -- too many decades of procedural and event-driven programming and only a few months of PLC ST programming...... I've created a visualization with a button that when pushed calls a method. I want the method to take a pressure reading, wait one minute and then take another pressure reading. I'm looking for leaks. I'm using TON for the delay. It seems like what is happening is that the method gets called once and it takes the first reading and starts the TON. But then execution continues, leaves that method call, and the second reading never happens. I can force the method to keep running until the whole thing is done with a While loop, but I understand that is considered BAD in PLC programming. If it push the button again to call the method again, it picks up where it left off and if the timer is complete then it runs the remaining code. How do I keep that method running until it is complete with just one call without using a while loop that ties up the PLC for a minute? Thanks! -Farren
Last updated: 2025-10-31

Post by fajean on Issue with library updates ^{CODESYS Forge talk (Post)}
We make heavy use of internally developed libraries, which are often nested on multiple levels. I routinely work simultaneously on several libraries along with a project that use them. I make changes to a library and immediately perform a download (online or otherwise) in the project. For the longest time, we had zero issue with this. But starting a good while back, with 3.5 SP19 I think, CODESYS started not noticing library updates in other instances most of the time. When the update is missed, the project sees no need to update the code, and any download ignores the new code. A "Clean all" does not solve the issue. But if I close and then re-open the project, then the new version is noticed and the download works. The other solution is saving the library to the registry multiple times (say, 20-30 times, less if lucky), and then at some point the project notices the changed library. I am now on SP21, and it is still not fixed. This is driving me mad, any tasks probably takes me double the time or more due to this problem. My colleague has the same problem on a separate computer. Is this a known issue? Is there a setting somewhere that changes how updates are checked? Thanks for any help!
Last updated: 2026-02-13

Post by tk096 on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Meanwhile, I would like to understand why the motion FB instances must still be called even after the Execute is set to FALSE, especially in view of the fact that the next instruction is programmed to abort the previous one, with BufferMode set to 'Aborting'. All these unnecessary FB calls are an unnecessary overhead on the CPU anyway. Is there any precise rule about when to cease calling the various instances? (It should precisely be the 'done' status that says this one has finished its work). In general: - Motion function blocks have to be called until they report 'Done', 'Error', 'CommandAborted' or a subsequent motion FB with BufferMode=Aborting is started in the current cycle. - Setting the Execute input to FALSE will not abort any ongoing motion of the motion function block. For example, one case that is often problematic is the execution of the Axis Halt instruction. When, after a MoveAbosulte instruction this returns the event as 'done' and indeed the axis is in standstill, the state machine first sets the move instruction to FALSE, and the next cycle sets the Halt request to TRUE. Some of the time everything works out fine. Occasionally, however, in this exchange, the axis goes into fault, also losing the OPERATIONAL state. I think the error SMC_FB_WASNT_CALLED_DURING_MOTION is only a follow-up (and misleading) error that results from the axis not being in operational state anymore (bus problems). Is there an error 'regulator or start not set' in the device log before the error 'motion generating FB wasn't called for at least one cycle'? Which error does the respective function block (Halt.ErrorId) report?
Last updated: 2024-07-22

Post by gerdkoch on Dynamic I/Os Mapping ^{CODESYS Forge talk (Post)}
Hi, I assume that you have a Pfc200 G2 or something and work with the original WAGO runtime. Then I would recommend the WagoSysDynamicIoMapping. Here in the example projects there is a PDF file for the library: https://downloadcenter.wago.com/learning-material/details/ll0w3pmdunzvem83g1 There is a global functional component in a GVL of the library. I think it's called DynKbusIoManager or something. The active terminals are registered there. Then there are filter Fb's for e.g. the first clamp with a specific article number. Everything is in the PDF.
Last updated: 2023-08-18

Post by dasch on eCockpit - unable to start simulation ^{CODESYS Forge talk (Post)}
This is a known bug in e!Cockpit. See Release notes of V 1.11: 1 e!Cockpit Release Version 1.11 (2022-07) ATTENTION: If a library that uses asynchronous tasks (e.g. WagoAppConfigTool, WagoAppCloud or function modules such as Dali-Master) is dragged into the project, the simulation cannot be started. It is already sufficient to add the library to the project (an FB does not even have to be instantiated). I guess you are using one of these libraries/modules in your project. We e.G. often use PWM modules, these are also affected.
Last updated: 2023-09-05

Post by nico01 on Integer with comma in visualization ^{CODESYS Forge talk (Post)}
Hello everyone, I created a visualization with a lot of REAL, with one or two digits after the decimal point. This causes me problems in terms of rounding and memory... is it possible to display an integer with a comma, like with PROFACE or SIEMENS? It's just an "abuse" of display, the comma is just on the visualization. This limits the memory (16 versus 64 bytes) and rounding is easier to manage... See print screen on proface software THANKS
Last updated: 2023-09-20

Post by macros8 on Translation - How to get text as reference in Frames translated? ^{CODESYS Forge talk (Post)}
Hi all, I need a help. I want to create Frame where some parameters are done via reference input to this frame. What I have realized that if I use for Label/Caption etc. string variable (%s) it is not included in translation list. This is a quite a big deal and I did not find way how to add text to the list manually. Would you give me a hint how to proceed? I hope there is a way (workaround) how to do it. Thanks a lot. M.
Last updated: 2023-12-01

Post by rafael on Access to user group IDs ^{CODESYS Forge talk (Post)}
Hello, I'm trying to access the group IDs of the connected user. "CurrentUserGroupId" var shows only the first group ID that the user is assigned, I need the other group IDs that the user is in. I find some structs but I can't find where they are used, like "VUM_User" scruct from visuusermgmt, where can I find this vars? https://content.helpme-codesys.com/en/libs/VisuUserMgmt2%20Interfaces/Current/VUM_User.html abyUserGroupIDs seens perfect but I can't find a GVL where it is used.
Last updated: 2024-07-08

Post by rafalkmiec on CodeSysControlWinV3x64 ^{CODESYS Forge talk (Post)}
Hello. I forgot the password to ControlWinV3X64. I watched on youtube that i must delete folder from "ProgramData/CODESYS/CODESYSControlWinV3x64" But the problem is that in the the CODESYS there is no folder named CODESYSControlWinV3X64. I checked if the folder is hidden but it's just not there. I can't find it and can't reset the password. Could you help me to reset this password. I even tried to uninstall and install the CODESYS but nothing helps.
Last updated: 2024-07-11

Post by rafalkmiec on CodeSysControlWinV3x64 ^{CODESYS Forge talk (Post)}
Hello. I forgot the password to ControlWinV3X64. I watched on youtube that i must delete folder from "ProgramData/CODESYS/CODESYSControlWinV3x64" But the problem is that in the the CODESYS there is no folder named CODESYSControlWinV3X64. I checked if the folder is hidden but it's just not there. I can't find it and can't reset the password. Could you help me to reset this password. I even tried to uninstall and install the CODESYS but nothing helps.
Last updated: 2024-07-11

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Yes, this point is part of my misunderstanding. Why, after the execution ot the motion FBs is set to FALSE and exsecuted at lest one time, it must be continuosly called, even if the motion control it's take from another subsequent instruction. This is what I really don't undertand, but what in fact it's happening. For example, in case of stopping a MoveVelocity FB, then Halting the motion by the related FB, the axis at spot goes into error. If there was bad trigger management, the various instructions would NEVER work.
Last updated: 2024-07-18

Post by mikek10 on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
I was answering your last paragraph Meanwhile, I would like to understand why the motion FB instances must still be called even after the Execute is set to FALSE, especially in view of the fact that the next instruction is programmed to abort the previous one, with BufferMode set to 'Aborting'. All these unnecessary FB calls are an unnecessary overhead on the CPU anyway. Is there any precise rule about when to cease calling the various instances? (It should precisely be the 'done' status that says this one has finished its work).
Last updated: 2024-07-18

Post by aliazzz on Unable to deploy Virtual Control SL on ARM64 (Raspberry Pi5) ^{CODESYS Forge talk (Post)}
An interesting remark for CODESYS Support. I found this after looking through the Runtime Deploy Tool messages when I connect to an AMD64 architecture Successfully Connected to Target ( {MyIP} - AMD64 ) when I connect to an ARM64 architecture (Raspberry Pi5) Successfully Connected to Target ( {MyIP} - ) As clearly seen in the attached .png, the AMD64 target is detected, while the ARM64 target architecture is not detected (displayed). I assume that this is the reason why the pulldown menu isn't populated correctly.
Last updated: 2024-07-28

Post by alexgooi on OPC-UA Boolean format ^{CODESYS Forge talk (Post)}
Dear Forum, We are currently making the switch from OPC-DA (Codesys server) to OPC-UA (Running on a Codesys controller). We are using Codesys version 3.5 SP 20. Our Scada system is expecting Boolean's to be represented as a 0/1 (True Boolean) but the OPC-UA server is representing a boolean as False/True This indeed matches the OPC-UA standard, but is there a way to configure the OPC-UA server's boolean representation? Thank you in advance
Last updated: 2024-08-06

Post by timvh on Stack overflow with really simple function ^{CODESYS Forge talk (Post)}
You have declared the function block in a function and call the instance also from a function. This is not correct, because a function is initialised with every call. The http client function block should be declared as Global Variable if you want to cal it from a Function, but probably it is better to declare it in a Program and also call the instance of the http function block from the same Program.... The variables of a Program are not initialised with each call.
Last updated: 2024-09-20

Post by rmaas on Webvisu cliënt responsiveness ^{CODESYS Forge talk (Post)}
hi, Does anyone know how to optimise the responisiveness of the web visualisation? When i open the webvisu on my laptop it is very responsive, no noticable lag. But when i open it on the HMI (web client) at the customer site there is a lag of +-500 when opening popups etc. The hmi used is: Phoenix Contact WP 6156-WHPS full hd Arm® Cortex®-A53, 1.6 GHz qt web browser The clients performance seems to be the problem, what can i do in my project to decrease the load for the client?
Last updated: 2024-09-28

Post by mtnkyr on Ethercat Master ^{CODESYS Forge talk (Post)}
Hi everyone, I am working on a 3 axes Cartesian robot. I take control of all the axes. In the Ethercat connection, the drive sequence is the same as in the program. For example, in the current program the order is as follows. 1. Axis_Z 2. Axis_X 3. Axis_Y Communication Diagram PLC->Drive_Z->Drive_X->Drive_Y When I try to change the order in the program while keeping the communication diagram the same, there is an axis drive mismatch. How can I fix this?
Last updated: 2024-10-22

Post by cillian on Error when opening HTML5Control Editor ^{CODESYS Forge talk (Post)}
Hello, I am new to this forum so apologies if this is posted in the incorrect area. I am getting an error when trying to open the HTML5 Control Editor - this was working fine previous days. I am using Codesys V3.5 SP20 Patch 3. I have reinstalled the application. Below is a screenshot of what shows when I attempt to open HTML5 Control Editor. Would anyone know the solution to rectifying this problem? Thanks in advance. Edit: This is now fixed.
Last updated: 2024-10-22

Post by winki on Modbus TCP Client ^{CODESYS Forge talk (Post)}
Hello, I am new on CODESYS env. I would like to do some Modbus TCP, but I am wondering If using codesys you must use the device "Modbus_TCP_Client" & "Modbus_TCP_Server". I would like to do it without device, only using ST. Is that possible ? I try the example : MODBUS_master_example, but it is not working. If it is possible to dot it without any Device I will show my code. Thx a lot
Last updated: 2024-10-25

Post by xabier on Problem Update new version Master ethercat ^{CODESYS Forge talk (Post)}
@eschwellinger...How can migrate to the new version if i can´t do it??? The project generate with CODESYS DEvelopmentsystem Version=3.5. SP16 Path9 ...I want open with my version 3.5 SP19 Patch 4...I can´t update the my last version of master ethercat(4.4.0.0) and is not possible. My situation is not the comment tell you ...my situation is impossible upadte new version of master ehtercat if you create the project with older version. Have you got a idea? Can you help me please?
Last updated: 2024-10-29

Sort by relevance or date