Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
I don't know why the EtherCat fails, but what happens is: First I have only one 1WireMaster running on my Raspberry Pi and EtherCat is running fine. Then I'd like to add a 2nd 1WireMaster. Therefore I enable a 2nd GPIO Pin on the raspberry in the file "/boot/firmware/config.txt". dtoverlay=w1-gpio,gpiopin=4,pullup=0 dtoverlay=w1-gpio,gpiopin=23,pullup=0 To be able to use this 2nd 1WireMaster in Codesys Runtime I Adjust the CODESYScontrol.cfg file and add there: PlaceholderFilePath.2=/sys/devices/w1_bus_master2, $OneWire2$ After a reboot the EtherCat Master is not working any more. I didn't even add a 2nd OneWire Master in Codesys, but still if I do the EtherCat does not work. Do you have an idea why?
Last updated: 2025-10-21

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
The machine I'm currently using (Celeron J1900) already has the Kernel RT patch. I checked the performance according to the documentation. After running CyclicTest for 4 cores, the value for each core is around 6-7. I went through the entire process according to the documentation (I envy the TaskMonitor results in the documentation). The documentation states: "CODESYS Virtual Safe Time Provider The CODESYS Virtual Safe Time Provider is a standard interface that the user can use to transfer a second and external time base to the CODESYS Virtual Safe Control. The implementation is done as a client, which must run on another system with an independent time base." How do I implement this? I've been struggling for two weeks now - I'm too old to give up.
Last updated: 2025-11-17

Post by msirotkin on EtherCAT status errors ^{CODESYS Forge talk (Post)}
Hello, I'm trying to understand the reason for the many errors on the EtherCAT master status page. If we set the cycletime to 1ms we see a lot of rxerrors and lostframes, but the send and recive times are quite good (see attachement). And the status of the EtherCAT bus is good (no other errors, all is green, slave has no errors) But when we set 2ms cycletime the lostframe errors are gone, but periodically increses rxerror counter (see attachement). The questions is, what do these errors actually mean and what we can do to get gid of them? Linux RT, imx8, Codesys runtime for ARM 3.5.21.10, Ethercat 4.10 Thanks
Last updated: 2025-11-25

Post by gseidel on Can't get SMC_SmoothPath to work ^{CODESYS Forge talk (Post)}
Hi bertus, I cannot see any problem in the code you posted. Just some ideas: What is the value of D_ANGLE_TOL? - Do you need the assignment bAbort := NOT bDecoder? Does it help to leave it out? Any errors (e.g. SMC_SmoothPath.Error/ErrorID) or PLC log messages? What if you comment out SMC_SmoothMerge and SMC_LimtiDynamics, is corner smoothing still not working? Is bDecode written from a different task (e.g. visu)? Then I would recommend to assign to a local variable (bDecodeLocal := bDecode) and use that for all FBs. Otherwise, FBs might see different values of bDecode in a single cycle, which will cause problems. Regards, Georg
Last updated: 2025-12-17

Post by infinitetool on No connection could be made because the target machine actively refused it ^{CODESYS Forge talk (Post)}
Hi! I'm having trouble connecting to a device in Deploy Control SL. I'm able to see the device is available during a scan, and I can ping the device as well, but when I try to connect I get the message "No connection could be made because the target machine actively refused it". I've worked on this for hours including turning off the firewall on the device PC but nothing seems to work. The device is running a fresh install of Windows 11 IoT Enterprise 2024 and the Development System is 3.5.21.50 running on Windows 11. Thank you in advance for any ideas!
Last updated: 2026-03-10

Post by sheberle on No Bootproject possible ^{CODESYS Forge talk (Post)}
Hello Alex, the message is generated by the CODESYS code generator based on the DevDesc settings of the memory areas available for the target. The problem arises when after too many online changes the area is full. Therefore no more boot project can be generated. Short-term remedy as described in the dialog: Clean and fresh download. This way the initial memory size will be "used" again After how many online changes did this error occur? There is no set limit on the number of online changes, but making too many changes could be a risk. br Simon
Last updated: 2026-03-31

Post by pernockham on Images not shown in webvisu ^{CODESYS Forge talk (Post)}
Two issues. Ive been struggling to get the user management the way I want it. I want to protect the device from unauthorized upload/download, but I do not want login requirement on webvisu. The combination that seems to work is to use "runtime device user management" while keeping the visu user management in "legacy mode"? Initially this seemed to work, but now images are not loaded when using direct access, while they are still shown if I access the webpage via Automation server. Im guessing its connected to the authorization changes? Anyone able to help out? Thanks Also, I read that legacy mode should be avoided, is it possible to use "runtime based visu user management" while keeping direct access to the webpage without login. System is a "Control for linux SL, version 4.20.0.0" Per
Last updated: 2026-04-10

Post by arwie on Frustration-Fueled Feedback on Project File Management and Git Integration ^{CODESYS Forge talk (Post)}
An other approach is to split the application into a hard real-time part running in CODESYS and the business logic running in Python asyncio. The business logic part is usually bigger and changes more often. As Python code is pure text, vscode and git are your friends. A performance example on YouTube (CODESYS SoftMotion + Python): https://www.youtube.com/watch?v=BT-L0H_4Aic Docs and code on GitHub: https://github.com/arwie/controlOS_demo/blob/main/docs/codesys_python_link.md Real-time variable exchange between a CODESYS application and a Python application running in parallel, using POSIX shared memory.
Last updated: 2026-06-21

Post by charly29160 on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hallo Herr Schwellinger - Danke für die Info. Der Fehler besteht weiterhin: Follow-up: Rootless mode is not the cause here — verified with ps aux, the runtime binary runs as root: root 1974 48.9 0.7 854852 62140 ? SLl 13:00 0:04 /opt/codesys/bin/codesyscontrol.bin /etc/codesyscontrol/CODESYSControl.cfg gpioinfo gpiochip0 as root also works flawlessly (all 54 lines listed correctly, no permission errors at the kernel level). So the block is happening purely inside CmpCharDevice's own sandboxing, not at the Linux/kernel permission level and not due to a dedicated unprivileged user. The correct config key to whitelist /dev/gpiochip0 for CmpCharDevice is still what I'm looking for. Im Voraus herzlichen Dank für Ihre Hilfe Karl Schuler
Last updated: 2026-07-20

Post by charly29160 on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hallo Herr Schwellinger - Danke für die Info. Der Fehler besteht weiterhin: Follow-up: Rootless mode is not the cause here — verified with ps aux, the runtime binary runs as root: root 1974 48.9 0.7 854852 62140 ? SLl 13:00 0:04 /opt/codesys/bin/codesyscontrol.bin /etc/codesyscontrol/CODESYSControl.cfg gpioinfo gpiochip0 as root also works flawlessly (all 54 lines listed correctly, no permission errors at the kernel level). So the block is happening purely inside CmpCharDevice's own sandboxing, not at the Linux/kernel permission level and not due to a dedicated unprivileged user. The correct config key to whitelist /dev/gpiochip0 for CmpCharDevice is still what I'm looking for. Im Voraus herzlichen Dank für Ihre Hilfe Karl Schuler
Last updated: 2026-07-20

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, basically the i950 drive support CiA402 Basic and CiA402 Advanced modes. I attached pictures of both mode supported functions. It also support CSP, VL, CSV and CST modes. It seems the homing mode is in CiA402 Advanced mode but how can you not have the homing mode in both modes? It is a vital part of any servo system. If I use the SoftMotion standard demo mode, I can move the servo absolute and relative but cannot home it. But in SoftMotion Light mode, I cannot execute any motion function. Here is the official manual for i950 servo drive - i950 Documentation Best Regards Konstantin Kolev
Last updated: 2026-02-13

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
And the strange thing for me is that if i connect with an older IDE version (where I only have 4.17.0.0 installed) I can see both "CODESYS Control for Linux SL" and "CODESYS Edge Gateway for linux". And that I loose (both presence and possibility to update) the first option (Control SL) if i let the updater install "Control for linux SL" vers. 4.18.0.0 or later. (Note that runtime 4.17.0.0 is installed and it is running and I can login to that system, but no apparent option available to update it to 4.19.0.0). Attached print screen where I connected the "deploy sl tool" to the same system, where the upper (IDE) one has 4.19.0.0 installed, while the lower one has 4.17.0.0 installed..
Last updated: 2026-02-17

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
I am experiencing an issue when trying to define the Y-axis limits in a Trend Graphic using variables. When I set the Minimum and Maximum values as variables, an error is triggered. My goal is to make the Y-axis limits dynamic so they can adjust according to the installation. Both variables are initialized as follows: gP_YMin = -100.0 gP_YMax = 100.0 However, I still get the following error: "The minimum axis value must be less than the maximum axis value" Does anyone have an idea why this is happening or how to resolve it?
Last updated: 2026-03-22

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
I am experiencing an issue when trying to define the Y-axis limits in a Trend Graphic using variables. When I set the Minimum and Maximum values as variables, an error is triggered. My goal is to make the Y-axis limits dynamic so they can adjust according to the installation. Both variables are initialized as follows: gP_YMin = -100.0 gP_YMax = 100.0 However, I still get the following error: "The minimum axis value must be less than the maximum axis value" Does anyone have an idea why this is happening or how to resolve it?
Last updated: 2026-03-22

Post by rik123456 on Alarmmanagement – Dynamic Alarm List ^{CODESYS Forge talk (Post)}
Hi, I had a question about alarm management in the CODESYS visualization. I am currently investigating to what extent the alarm visualization can be built dynamically. In my program, I have developed a motor block that is used for multiple motors. When the emergency stop of one or more motors is activated, the corresponding motors are displayed in the alarm list (see image). This works quite well. I achieved this by linking variables to a latch, after which a piece of code displays the motors that are in emergency stop. My question is: do I need to create a separate latch for each motor or can I use a single latch to display multiple alarms of a motor underneath each other? This would then look like this: Time…: M1 Emergency Stop Active Time…: M4 Emergency Stop Active
Last updated: 2026-04-20

Post by alex-n on Problem with keeping up the distance between two axes ^{CODESYS Forge talk (Post)}
Hello. I have a task to synchronize the movement of two axes and maintain the distance between them. First axe makes equal steps by trigger using MC_MoveRelative function. The second one is standstill and after another signal should catch up the first one from its position to a specified distance and keep it. I've tried to use MC_Phasing and mostly it works. Second axis catches up the first and starts make step with it. But in one moment this axis can crash into the first and there is no clear connection as to why this is happening. It can work correct for a day or for a week.
Last updated: 2026-06-04

Post by r-niedermayer on C0564 Warning Message ^{CODESYS Forge talk (Post)}
Please see or Online Help on how to initialize variable before using them: https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_pragma_attribute_global_init_slot.html Regarding the Attribute global_init_slot: You can use this pragma to influence the order in which signatures are processed during global initialization. It can only be applied to signatures. By default, the initialization sequence for variables from global variable lists is undefined! However, if, for example, variables from one list depend on variables from another list, it is necessary to initialize one before the other. (Aee OLH and Syntax) The placeholder <slot> must be replaced by an integer value that defines the position in the initialization sequence.</slot> The default value is 50000. A lower value causes an earlier initialization! If several signatures have the same value for the 'global_init_slot' attribute, the order of their initialization remains undefined! Cautious application should therefore be considered! Example: The project contains f.e. two global variable lists GVL_1 and GVL_2. The global variable "A" is part of the global variable list GVL_1: {attribute 'global_init_slot' := '300'} VAR_GLOBAL A : INT:=1000; END_VAR The initialization values of the variables "B" and "C" of GVL_2 are dependent on the variable "A". {attribute 'global_init_slot' := '350'} VAR_GLOBAL B : INT:=A+1; C : INT:=A-1; END_VAR So if you set the 'global_init_slot' attribute of the global variable list GVL_1 to 300, i.e. to the lowest initialization value in the example, then it is ensured that the expression "A+1" is well-defined at the time of initialization of "B".
Last updated: 2024-01-30

Post by gilad on CODESYS SoftMotion Generic DSP402 on WAGO PFC200 + Festo CMMT-AS: MC_Power stays Busy, Controlword remains 0 ^{CODESYS Forge talk (Post)}
Hello, I am trying to connect a Festo CMMT-AS-C4-3A-MP-S1 servo drive to a WAGO PFC200 (750-8210) using EtherCAT and CODESYS SoftMotion. Hardware PLC: WAGO PFC200 750-8210 Drive: Festo CMMT-AS-C4-3A-MP-S1 Communication: EtherCAT CODESYS version: Device description version 6.3.1.1 Drive firmware: 36.10.3 Current Status EtherCAT communication is working correctly: EtherCAT master = Running Drive detected and operational PDO input and output mapping is active Statusword, position and velocity are updating correctly Current PDO mapping: Outputs: 6040 Controlword -> %QW0 6060 Modes of operation -> %QB2 607A Target position -> %QD1 60FF Target velocity -> %QD3 Inputs: 6041 Statusword -> %IW2 6061 Modes of operation display -> %IB6 6064 Position actual value -> %ID2 606C Velocity actual value -> %ID3 SoftMotion Axis I added a SoftMotion CiA402 axis under the EtherCAT slave: Axis type: SM_Drive_GenericDSP402 Axis communication state: operational (100) No SoftMotion mapping errors anymore Problem MC_Power is executed with: Enable = TRUE bRegulatorOn = TRUE bDriveStart = TRUE but: Status = FALSE Busy = TRUE Error = FALSE ErrorID = SMC_NO_ERROR The axis remains in: SMC_AXIS_STATE.power_off DSP402 state = SWITCH_ON_DISABLED The most important observation: Statusword = 32784 (0x8010) Controlword (%QW0) remains 0 all the time SoftMotion never writes 6, 7, or 15 to the Controlword. Additional Information The axis status page reports: "The license is missing or invalid. The PLC runs in demo mode." I am not sure whether: The missing SoftMotion license prevents Controlword generation completely. The axis is still not correctly connected to the EtherCAT slave despite operational communication. There is an additional CiA402 configuration step required for the Festo CMMT-AS drive. Has anyone successfully used a Festo CMMT-AS MP drive with CODESYS SoftMotion Generic DSP402 on a WAGO PFC200? Any suggestions on what should be checked next would be greatly appreciated.
Last updated: 2026-06-24

Post by deeps on web visu on IFM ^{CODESYS Forge talk (Post)}
I have an IFM cr1077 display. I would like to show B&R mapp view on IFM visualization. I used coedsys web browser elemnt for this. I could see IFM working fine in Internet web browser but IFM device shows white screen and freezes. I think there is problem with IFM showing the web browser. Is my understanding of the web visu right? am I doing any mistake here?
Last updated: 2023-08-18

Post by rossanoparis on After un upgrade of "CODESYS Control for Raspberry Pi MC SL" from v4.7 to v4.9 SysFileOpen function stopped working ^{CODESYS Forge talk (Post)}
For those who will step on this thread. Everything is fine, I had only to increase by 1 my place holders number. For sure the system is occupying the number 1 without being declared ... Below the modification I made to get my code working. [SysFile] PlaceholderFilePath.2=/home/pi/hpca/bin, $hpcabin$ PlaceholderFilePath.3=/home/pi/hpca/cfg, $hpcacfg$ PlaceholderFilePath.4=/home/pi/hpca/logs, $hpcalogs$ PlaceholderFilePath.5=/home/pi/hpca/resources, $hpcares$
Last updated: 2023-08-22

Post by fabian on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
Hi all, Is there an update on this topic? Same problem here, I can not add more than 10 Modbus-Slave channels. Is there a workaround? Many thanks! Fabian Codesys 3.5.19 SP2, Modbus 4.3.0.0, Name: Modbus TCP Slave Hersteller: 3S - Smart Software Solutions GmbH Kategorien: Modbus TCP Slave Typ: 89 ID: 0000 0005 Version: 4.1.0.0 Bestellnummer: - Beschreibung: Ein Geraet, das als Slave für einen Modbus TCP Master konfiguriert ist. Version Konfiguration 3.5.11.0
Last updated: 2023-08-28

Post by martinlithlith on Relay board / relays for raspberry pi 3 b+ ^{CODESYS Forge talk (Post)}
hi! im planning a project on a raspberry with Codesys. For this I'll need a number of relays to control heating and fans, all a max of 24v and about 2a. How would i know if the board / relays i buy will be working with Codesys? Does every hat work or does it need a library/driver? is there a list of drivers/libraries created? as this is a hobby project all tips on a relay board or single boards that works with codesys and not to expensive are very welcome.
Last updated: 2023-09-03

Post by macros8 on Alarm Management - latched variable represented as Text list ^{CODESYS Forge talk (Post)}
Hi all, in Alarm management you can latch some variable to show value within the alarm msg. It´s very useful sometime. But I´m wondering whether there is any possibility to represent that value as Text list. It´s quite common in other HMI tools and this is very useful in case of using some ErrorID for detail specification of error. Unfortunately I could not find any way how to do it but I believe that exists :) Thanks a lot. M.
Last updated: 2023-09-06

Post by transmin01 on CANbus issue ^{CODESYS Forge talk (Post)}
Update: This initial issue was when using a Linux target PLC. Since then I have created a Win10 target PC and the Codesys software reported an issue associated with the device version (see attached). I am assuming this is an incompatibility with the xml file from the manufacturer and the firmware version on the module and I am chasing this up with Beckhoff. Question is, why would this not report with a Linux target?
Last updated: 2023-09-14

Post by timvh on CANbus issue ^{CODESYS Forge talk (Post)}
On a PC with the Control Win, this is probably related to the fact that the CAN drivers are not loaded. Go to the folder where your Control Win Configuration file is: - E.g. C:\ProgramData\CODESYS\CODESYSControlWinV3x64\E1FA7ABE - Open the CODESYSControl.cfg - Remove the semi-colon in front of the CAN driver you want to use (section ComponentManager). - Set the component ID to the next number in the list (e.g. Component.8) - Save this file and restart the Control Win.
Last updated: 2023-09-14

Sort by relevance or date