Post by gatto on Two licenses have to be installed forgot to enable one license ^{CODESYS Forge talk (Post)}
Hi. What type of PLC do you have? What activation method do you use? What license ticket did you purchase and want to activate? Can you describe the process you followed step by step?
Last updated: 2026-02-02

Post by derpaul on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
Hello, my PFC200 has run for a few month now without problems. But now it freezed 2 times a day. LEDs were green but the PLC was not reachable. After power off -> on. I found that the MQTT had an error: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED. And MQTT hadn't reconnect since then. I tried a cold and a warm reset but nothing helped. How can I solve this? Regards, Paul
Last updated: 2023-09-21

Post by maxkemmeren on PFC200 (750-8214) high linux load average, but seems random. Possibly EtherCAT related. ^{CODESYS Forge talk (Post)}
Have you received any feedback or found any solutions to the load problem. We are running into similar issues, even without codesys running the load avarage is above 1 meaning that it is to busy already without plc code running. Hope you might have some more insight.
Last updated: 2024-07-11

Post by flappyman on licenses question ^{CODESYS Forge talk (Post)}
I hope this tread will be able to help me. I got your new licenses and it was working perfectly fine. Unfortunately, my PLC got severely damaged and it can not run anymore. Is it possible to somehow release the license so I could use it again. I have all information for the device and can provide it.
Last updated: 2024-08-05

Post by winki on Not Possible to connect using control SL ^{CODESYS Forge talk (Post)}
Hello, I used to connect into my gateway using control SL tool 4.13, (it was called Update Linux.) I formated my computer, so today I install the new version of codesys and all package. Now I am not able to connect to my PLC using control SL. It says, check the status. Normally it used to worked perfectly before that.
Last updated: 2025-01-07

Post by fabiodasilveira on PLC Shell commands via ST Code ^{CODESYS Forge talk (Post)}
Thank you, Bingo. I have added the instructions below to the CODESYSControl.cfg file, but they haven't changed anything. [SysSocket] Adapter.0.Name="ETH0" Adapter.0.EnableSetIpAndMask=1 Adapter.1.Name="ETH1" Adapter.1.EnableSetIpAndMask=1 Regarding your second suggestion, could you please expand a bit on that?
Last updated: 2025-03-03

Post by chanmina on Engineering IDE from linux? ^{CODESYS Forge talk (Post)}
For a long time now, I have used VirtualBox on a Linux Mint host to run the Codesys IDE without any problems. Every day, I put it to good use, and it never fails. Wine is not something to be trifled with. Probably not worth the effort. For Linux PLC developers, Codesys Go might be a game-changer. Very excited to give it a try.
Last updated: 2025-05-27

Post by matthew on Persistence Manager Backup ^{CODESYS Forge talk (Post)}
Hi @eschwellinger yes I have been using xDoubleStorage It happened again and I checked and the files were still there with there contents, restarting codesys or rebooting would not even reload them. Doing a download and then starting the PLC loaded them and began working again. Some sort of mismatch error or something?
Last updated: 2024-05-14

Post by imdatatas on Auto Declare window disappears by itself in the Ladder editor ^{CODESYS Forge talk (Post)}
Hello Everyone, The "Auto Declare" window disappears by itself in the Ladder editor. For example, a new function block is wanted to be added to the Ladder editor. (For example; MC_Jog block and instance name will be fbMcJog). To do this, "Empty box with EN/ENO" is added to the ladder line from the Toolbox on the right and when you type MC_Jog in the empty box and press enter, normally the "Auto Declare" window appears and you are expected to be asked to write the instance name here. However, this "Auto Declare" window closes itself immediately, it does not wait for the user to enter a value or close the window. I often encounter this situation in many IDE versions. Does this seem like a bug? If anyone has encountered a similar problem while creating a new program name, function or function block instance name regarding the "Auto Declare" window and knows a solution, I would be glad if you could share it. Best wishes Imdat
Last updated: 2025-03-06

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, In our workshop we have a Lenze i950 servo drive that has an EtherCAT bus and CiA402 compatibility. The WAGO is PFC200 750-8212 and as per documentation it has built-in license for SoftMotion Light functionality. It is not capable of supporting the full SoftMotion functionality like gearing and synchronizing. I added the EtherCAT esi files from Lenze and the EtherCAT master does see the drive, then I added a SoftMotion Light Axis object. The problem is that I can only energize the axis, I cannot execute any other commands. I set the positive and negative torque limits from the PDOs to 200% and when I try to move the axis by force it does not move back to its original position. I use the SML function blocks from the PLCOpen library and the error from the function blocks is that the op mode cannot be changed. Then I tried using a standard SoftMotion axis object and everything works fine, except the MC_Home function block. The axis moves back to its position when forced out of it. I follow this guide from Lenze - Lenze i950 CODESYS V3 What could cause this issue with the SoftMotion Light axis object? Best Regards Konstantin Kolev
Last updated: 5 days ago

Post by fajean on Issue with library updates ^{CODESYS Forge talk (Post)}
We make heavy use of internally developed libraries, which are often nested on multiple levels. I routinely work simultaneously on several libraries along with a project that use them. I make changes to a library and immediately perform a download (online or otherwise) in the project. For the longest time, we had zero issue with this. But starting a good while back, with 3.5 SP19 I think, CODESYS started not noticing library updates in other instances most of the time. When the update is missed, the project sees no need to update the code, and any download ignores the new code. A "Clean all" does not solve the issue. But if I close and then re-open the project, then the new version is noticed and the download works. The other solution is saving the library to the registry multiple times (say, 20-30 times, less if lucky), and then at some point the project notices the changed library. I am now on SP21, and it is still not fixed. This is driving me mad, any tasks probably takes me double the time or more due to this problem. My colleague has the same problem on a separate computer. Is this a known issue? Is there a setting somewhere that changes how updates are checked? Thanks for any help!
Last updated: 2 days ago

Post by bertcom on STRING conversions to DWORD ^{CODESYS Forge talk (Post)}
Good afternoon. I want to communicate with a Domino Industrial Printer using its Codenet protocol. The printer wants a series of Hexadecimal characters with no spaces or '00' characters. Because of that i chose the option to make the prefix and subfix for my code in a string. I have variable data in another string. With a complete program of a lot of CONCAT functions i eventually get the format of code that the printer accepts ( tested it with the hercules tool). Hercules String : 1B4F513030311B7532626C61636B04 The problem is : Codesys adds automatically 'code' to the code to show it is a string. Codesys string : '1B4F513030311B7532626C61636B04' The printer does not understand this. My idea is to convert the string datatype to an LWORD. I have no idea how to do this. I random types in STRING_TO_DWORD, as return i get 0. That didn't worked. Also on internet the explenations around string converting in codesys are very limited. If there in anyone who can explain me how to do it, i would appreciate it a lot ! Thank you!
Last updated: 2025-01-29

Post by mubeta on Profibus DP master with EL6731 and automatic restart of slaves ^{CODESYS Forge talk (Post)}
WHEREAS, I have already searched various posts and forums, where mostly there are few references and mostly geared toward integration in TwinCAT. I am looking for how to properly configure the EL6731 board as a DP master, (where I have its 3S license), with CoDeSys 3.5.19.x. I have three types of slaves, all integrated with their GSD descriptors. In the tab for the various slaves, I don't see options related to node restart on 'station return'. On the card manual, I read that for each slave I should be able to configure parameter 8000:2C: “8000:2C Restart behavior after DP fault Reserve, must be 0 BIT1 RW 0x00 (0dec)” However, in the project I see no way to configure this parameter, in any of the boards; and the arrays do not always have such an extensive size; most of the time they are only two or three words in size. The problem is that, after the hot reset of CoDeSys, the master restarts by starting all slave nodes, but if one or more get lost and go offline, there is then no automatic restart upon their return. I would need to figure out any solution, even via software, how to figure out that this one is back available and restart it.
Last updated: 2025-02-02

Post by sunfloweeerrry on Edgelogix-rpi-1000-cm4102032 SPI port connection to PiFace I/O Driver in CodeSys. ^{CODESYS Forge talk (Post)}
Hello, I hv a problem. Couldn't solve this for 2 days now. So I'm quite new at CodeSys and I have to use the spi port x30 on the edgelogix rpi 1000. So what I have to do is just 'add device' at the SPI where I hv to pick the 'SPI master' after that I hv to change the parameters according to the edgelogix I did found in the spidev.h but nothing got updated so I 'add device' again where I pick the PiFace I/O Driver and I put my variables at the I/O Mapping, which i put the input startbit at the in part and led at the out part. I want to make the led blink according to my structured text code but somehow the hardware didn't connected with the CodeSys spi port. Nothing happens. Any idea what I have to do?
Last updated: 2023-08-18

Post by kleeswi on Visualization scaling problem with B&R T30 panel ^{CODESYS Forge talk (Post)}
The probelm arises for the B&R T30 panel after updating Codesys from 3.5.17 to 3.5.19 patch 5. We have to use 3.5.19 for other reasons so we cannot downgrade the version. The scaling problem only exists for the B&R 6PPT30.0702.20F025 panel, the B&R T50 panel and a esa lumia panel work. When we choose a fixed resolution it looks also good, however we also want to support the esa lumia panel with a different resolution. The images show the anisotropic and isotropic option. In the anisotropic option it scales the hight correctly but not the width and in the isotropic option is scales both hight and width false, it also does not start in the top left corner. Does someone have any suggestion why it does not work anymore with the new codesys version and are there workarounds? I added all versions with visualization packages as an image, visuElems is 4.4.0.0.
Last updated: 2024-07-29

Post by danieldiaz on Problem with FB execution ^{CODESYS Forge talk (Post)}
Hello everyone, I've been working on a system which needs an error function, with this purpose I've created a FB programmed in LD, after debugging I run the simulation. It seems that the variable linked to a coil doesn't change the value when the contacts are associated to input variables. When I use internal variables the logic works properly. I don't know if the problem is related to the variables definition or with the logic program. As you can see in the image, I1 and I2 are variables declared on the FB, the rest are input variables. If I force the eStop and Reset signals to TRUE the coil value should change, but it doesn't. However in the second network if I1 is TRUE the coil change to TRUE as it has to be. To sum up, my doubt is why that coil doesn't change its value? I would like someone to shed a light on this. Thanks!
Last updated: 2024-04-02

Post by manuknecht on Detect "Cancel" Press in FileOpenSave Dialog ^{CODESYS Forge talk (Post)}
Thanks for your response! It seems like the VisuElems library has updated functions to the ones you used but apparently these older ones still work, even if I couldn't find them in the library documentation and they are also not suggested automatically by Codesys (when using Ctrl + Space). However, its precisely what I was looking for and it works. Thanks!
Last updated: 2023-09-20

Post by turndapage on Can't Add Symbol Configuration ^{CODESYS Forge talk (Post)}
I've got a Weintek HMI with CodeSYS built-in. I've got it connecting to CodeSYS and downloaded. The connection guide says I need to add a symbol configuration by right-clicking on the application and adding it, but it does not show up in the available objects. Is there something else I have to do to create a symbol configuration object?
Last updated: 2023-10-04

Post by timvh on Send file from codesys to...... ftp, cloud, etc ^{CODESYS Forge talk (Post)}
You can use the (open source) FTP client in Forge. This works on 64 bit systems. See: https://forge.codesys.com/prj/ftp-client/code/HEAD/tree/ As this is open, the idea is that when you use it and make improvements to the source code, that you also commit this in a branch so others can also benefit from it.
Last updated: 2023-11-07

Post by ewi04 on Recipe Manager - RecipeManCommands, load & write wrong values, Bug? ^{CODESYS Forge talk (Post)}
The individual structures were declared in a separate global variable list on a trial basis. But even this did not change the behavior. A total of 1667 variables are processed in a recipe. A reduction (e.g. saving only the first three drive parameter sets) also brought no change.
Last updated: 2023-11-15

Post by spoun on Problem with edge gateway config mode ^{CODESYS Forge talk (Post)}
I installed patch 3 now and i get a new message, although i located and modified the files in system32 and sysWOW64 still doesn't work. One thing i noticed is thta in system32 folder CODESYSGatewayV3 now i have two different XXXXXXXX files with the latest being created today at the time of installation
Last updated: 2024-10-21

Post by rafaelbrito on Integration C Code ^{CODESYS Forge talk (Post)}
I tried to use C code in the library that I have been developing in the project, but without success. I tried to use the CODESYS Control SL Extension Package to generate XXXdep.h and XXXltf.h, but without success. Do you have a better example of how to generate these files and how to compile them?
Last updated: 2024-12-03

Post by s1ack on Wago PFC200 Ethernet / IoDrvEthernet Issue? ^{CODESYS Forge talk (Post)}
I changed the interfaces to br0 & br1 as they are designated on the Wago PFC200. That issue is resoved. However, on site I have very high system cpu usage, system as in Linux. Presently it is not known why - my bench system does not exhibit such high system usage. In the past this was due to IGMP network traffic every 250uSec from synchronized inverters.
Last updated: 2025-01-22

Post by jeffersonhui on SP20 Visualization Element Dynamic Colors ^{CODESYS Forge talk (Post)}
I am using Codesys SP20 patch 5 and in a visualization element, the "Color variables" section does not have a section to set up dynamic color values linked to variables. In a previous version (SP18), I get the option to add variables for Normal & Alarm state colors. Does anyone know how to get the dynamic color variables to work?
Last updated: 2025-02-19

Post by eksheep on Unit Tests and C007: Unknown Type ^{CODESYS Forge talk (Post)}
Hello, I am attempting to implement unit tests for my POUs. When building and running the unit tests I receive error C007: Unknown Type for all types defined in the library, Standard, 3.5.18.0. Which is included in the POU Library Manager. Any input would be appreciated. TIA.
Last updated: 2025-08-27

Sort by relevance or date