Post by mikek10 on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
I was answering your last paragraph Meanwhile, I would like to understand why the motion FB instances must still be called even after the Execute is set to FALSE, especially in view of the fact that the next instruction is programmed to abort the previous one, with BufferMode set to 'Aborting'. All these unnecessary FB calls are an unnecessary overhead on the CPU anyway. Is there any precise rule about when to cease calling the various instances? (It should precisely be the 'done' status that says this one has finished its work).
Last updated: 2024-07-18

Post by ph0010421 on Help with __SYSTEM.VAR_INFO ^{CODESYS Forge talk (Post)}
hi all I have a FB with IN/OUT variable. Inside the FB, I want to get the address of the IN/OUT variable. If I use __SYSTEM.VAR_INFO, I get the address of the FB copy rather than 'external' variable. VAR_IN_OUT MyVar: bool; END_VAR VAR Info: __SYSTEM.VAR_INFO; END_VAR Info := __VARINFO(MyVar); This give me the address of MyVar but I actually want the address of the variable passed to MyVar Any clues please?? thanks, ph
Last updated: 2025-01-24

Post by kuapiz on Camera RTSP Feed ^{CODESYS Forge talk (Post)}
Hello, I'm facing the same problem, I can access the FLIR AX Series camera through the IP converter software (go2rtc). In the CODESYS 3.5.19 patch 7 software, the streaming does not appear in the webvisu even using the URL "http://xxx.xxx.x.xxx:1984/stream.html?src=flirr". I used the "RTC" and "MJPG" modes. HW: PFC200 750-8217/600-000. FW: v27. If anyone has a solution, could you help us?
Last updated: 2025-03-05

Post by kuegerls on OpC UA server on Raspberry Pi MC SL - Certificate Issue ^{CODESYS Forge talk (Post)}
Hello, I have set up an OPC UA server following several guides, including this one: https://revolutionpi.com/documentation/tutorials/opc-ua-codesys-nodered/. The license for the runtime is installed on the device. However, I am unable to create a certificate for the OPC UA server in the security screen. I always get the error message: "The certificate has not been created by the device." Does anyone have an idea what might be causing this issue? Any help would be greatly appreciated! Thanks in advance! Best regards, Stefan
Last updated: 2025-04-02

Post by josul on Web Client HTTPS Communication Issue ^{CODESYS Forge talk (Post)}
Thank you for the suggestion. There is a certificate created in the quarantine directory relating to the URL used for the webclient FB. This certificate should have been valid as it was created only the week before this problem was encountered. I investigated a separate location using the same https URL and it has 2 certificates in the same quarantine directory, 1 is created almost 200 days ago, the other over 100 days ago. There have been no similar problems encountered with these certs or https at all.
Last updated: 2025-06-09

Post by imdatatas on Use MC_Home without enabling the drive for homing method 35 ^{CODESYS Forge talk (Post)}
Hello, As far as I know, no matter which home mode is selected, the axis must be in Standstill mode to run MC_Home according to PLCopen state machine. However, if the function you want can already be done from a parameter in the driver of the vendor you are using, you can try to perform the same function by sending the required value to that parameter via communication with the SDO write command. Regards, Imdat
Last updated: 2025-06-25

Post by timvh on How to change keyboard layout on the virtual keyboard? ^{CODESYS Forge talk (Post)}
Maybe you have the "Devices" tab open(?), but the "templates" are in the POU pool. You can open it from the menu: View - POUs, or if it is already open, select the POUs tab which is normally next to the Devices tab. All objects which are part of a library are in the POU pool, because they should be device independent (at least most of them).
Last updated: 2025-09-18

Post by food on Beaglebone Black OPC-UA Server ^{CODESYS Forge talk (Post)}
Man, this was a long time ago. I think the problem probably stemmed from not loading the certificates from the client and the server on the server and client respectively in the correct manner. I believe I ended up getting around it just by removing all security on the server. In the end we did not move forward with that architecture so I never had to actually fix it.
Last updated: 2024-04-10

Post by hoatran on Use third party actuator with IO-Link Master (IFM) ^{CODESYS Forge talk (Post)}
The generic sensor FB is for controlling the sensor via its cyclic input (PDI) and output (PDO). In this case, ifm raw cyclic input and output data are WORDs (16 bits total) The PDO data from the Buerkert unit are SINT (8 bits) In this case, I would use the unpackword fb from the CAA memory library to unpack the valve feed back value into the appropriate location.
Last updated: 2024-04-23

Post by dkugler on Alarm State Icon ^{CODESYS Forge talk (Post)}
thank you for pointing me to this "bug"!! I haven't recognized, the bit is reset after the first alarm is gone. I use this only for warnings, so it's not a drama, but was not correct in the past. I solved it now simply stupid by counting up a variable every time an alarm appears and decreasing it if an alarm is gone. The "warning lamp" is activated by checking the counter is > 0 The nice side effect, i'm able to show the number of active alarms in the state line now.
Last updated: 2024-04-24

Post by mondinmr on First IO address of a CAADiagDeviceDefault. ^{CODESYS Forge talk (Post)}
I have a device CAADiagDeviceDefault: IoConfig_Globals.Axis_A In our library, we perform introspection of the Etc_SlaveDiag. In that case, we have connectors, and by searching for them by address, I can find them in the IO mapping using the offset and size provided by EtherCAT. However, a Lenze i700 drive, instead of placing the IO mapping in the Etc_SlaveDiag device, places it in a sub-device CAADiagDeviceDefault. So, when I perform introspection, I cannot find the IO correspondences. Yet, in the CAADiagDeviceDefault, I do not find the connectors and cannot do the matching. Is there a way with a pointer or reference to a CAADiagDeviceDefault to obtain the address of the first input and the address of the first output? This is because we have our own motion library with many EtherCAT devices that automatically configure the mappings, but I can't manage to do so with the Lenze i700.
Last updated: 2024-08-22

Post by kurtk on dynamic modbus devices ^{CODESYS Forge talk (Post)}
I am CODESYS neophyte getting my wheels on. My goal is to re-platform an existing PLC application written in 61131 ST I've got the majority of the code/variables in a compilable form - excluding all the IO and comms nuances I am not sure whether this the right forum An important functionality which I implemented on the other platform was totally dynamic modbus devices... Most configurations I have come across impose static MB configs in which all configured devices MUST be present and functional... I have monkeyed around with MB enough to know that herding a half dozen MB cats into a working config can be tricky. I just do them one at a time and dynamically turn them on/off in whatever combination is convenient with ID, IP, baud, parity etc being runtime tweakable. I am totally curious whether this is possible with codesys, or whether its device configuration corrals one into a static cage which requires re-building the code to support flexible variations. Best regards
Last updated: 2025-08-19

Post by kurtk on runtime dynamic modbus devices ^{CODESYS Forge talk (Post)}
I am CODESYS neophyte getting my wheels on. My goal is to re-platform an existing PLC application written in 61131 ST I've got the majority of the code/variables in a compilable form - excluding all the IO and comms nuances I am not sure whether this the right forum An important functionality which I implemented on the other platform was totally dynamic modbus devices... Most configurations I have come across impose static MB configs in which all configured devices MUST be present and functional... I have monkeyed around with MB enough to know that herding a half dozen MB cats into a working config can be tricky. I just do them one at a time and dynamically turn them on/off in whatever combination is convenient with ID, IP, baud, parity etc being runtime tweakable. I am totally curious whether this is possible with codesys, or whether its device configuration corrals one into a static cage which requires re-building the code to support flexible variations. Best regards
Last updated: 2025-08-19

Post by mubeta on Strange problem with the ‘MC_SetPosition’ function ^{CODESYS Forge talk (Post)}
CoDeSys 3.5.19.7 Target Berghof MX6 In a simple SoftMotion programme with two stepperless modular axes from CMZ, one is simply controlled in speed, but a spot must perform a positioning. I use the function MC_SetPosition() both to reference the axis at power-up and also to correct the actual position to a fixed machine reference detected with proximity. The function has only one instance and I actually use a booelan variable to control the ‘Execute’ input. Well, I cannot correctly change the axis position on the fly if it is running at high speed. The servomotor works in a speed range between 0°/s and 720°/s, (gearbox output with a 1:6 ratio). As long as the servomotor is operating at speeds below about 400 °/s, the function is able to correct the position correctly even when forcing values far apart, but at high speeds, from 400 °/s upwards, the correction no longer takes place. For example, trying to correct the position of 280° into 300° with absolute mode, the axis that is moving at speed actually shifts the position by a few degrees, not the expected 20. I don't understand why with the servo drive running slowly the position shift occurs correctly, while increasing in speed it no longer works.
Last updated: 2025-01-09

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Thank you for your interest. Your answers are in line with what I knew, so at least it comforts me that I did not misinterpret the situation. However, I don't have an exact match as, for this project over the past few days I have: 1) I have gone back to leaving the various FBs of the motion always called, all of them, and in the state machine I use a boolean to activate the various useful Execute. (But in the future I want to go back and try the programming technique with which I wanted to develop this project); 2) For the occasional error: SMC_FB_WASNT_CALLED_DURING_MOTION perhaps it was due to the fact that I had set the Ethercat bus synchronism only at the CAN master level, but not at the level of individual drives. I have now also activated it for the individual drives and it does indeed seem to have been resolved, but having also adopted the programming technique mentioned in point 1), I cannot say whether this was the solution to the problem, or instead the previous point. Is there an error ‘regulator or start not set’ in the device log before the error ‘motion generating FB wasn't called for at least one cycle’? I can't answer that right now. By now the machine is running and I am no longer there, at this one. Also, I seem to remember that the 'fbeFBerror' drive structure (5-element array), does not cycle, BUT ONCE THE 5 EVENTS AFTER SWITCHING ON, IT DOES NOT UPDATE ANYMORE (but that's another issue), so diagnostics were not easy.
Last updated: 2024-07-24

Post by laruso on Runtime device Enable/Disable procedure ^{CODESYS Forge talk (Post)}
I implemented the parts from the CAA Device Diagnosis Example.project and could use it for switching on and off, the CAN devices that were located under the CANbus and CANopen_Manager. But i can't do the same with I2C_master_test_version or devices below this one. In the example project there is only the EtherCAT Master, CANbus and CANopen_Manager, and Ethernet with devices below.
Last updated: 2023-10-27

Post by ggis on Unable to connect to git remotes through Codesys. ^{CODESYS Forge talk (Post)}
When trying to connect to a Github repository in the Git remotes windows of Codesys, the user can be the account username or the account email, while the password is the Github token. (I know this is an old topic, but I lost some time figuring it out from the guides.)
Last updated: 2023-11-10

Post by abauza on Image Pool using in other libraries ^{CODESYS Forge talk (Post)}
Hi I have done some tests and i realised that it's an issue with the visualizator simulator because i uploaded the program to a device and tried to see on the Web browser and I see correcctlu the images of the image pool of the library. I post this for anyone that have the same problem.
Last updated: 2024-08-20

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Just verified the behaviour. Still is the same. It should be attached here. But I also tried the DCF-file with the axis in the lab with the real drive: The MC_Power block never goes out of busy. Had not time to investigate further, though.
Last updated: 2024-01-08

Post by dkugler on Webvisu client connection monitoring ^{CODESYS Forge talk (Post)}
you can give this code snippet a try. It's extracted and simplyfied from my code: Install VisuElemBase lib if not installed yet. Execute in visu task: VAR pClientData : ARRAY [-1..100] OF POINTER TO VisuElemBase.VisuStructClientData; END_VAR VisuElemBase.g_ClientManager.BeginIteration(); pClientData := VisuElemBase.g_ClientManager.GetNextClient(); WHILE pClientData <> 0 DO pClientData[pClientData^.GlobalData.GlobalClientID] := pClientData; END_WHILE You have to make shure every no longer updated pointers in the array have to be deleted and no longer used by your code! Usage of this pointer access at your own risk :-) Works with SP16. From SP17 and newer there will be warnigs etc. using this solution as I remember. It will be great, if Codesys publishes a example or give a hint how to accesse this client values with the VisuUtil lib or other future-proof way!
Last updated: 2024-09-09

Post by micik on Python scripting - print whole project tree ^{CODESYS Forge talk (Post)}
Hello, I have found a script for printing device tree in Codesys project. This script is available as code snippet as an exmaple for using Python in Codesys. However I feel main documentation is lacking. For example, where can I find that object has "is_device" attribute? Code examples are given here: https://content.helpme-codesys.com/en/CODESYS%20Scripting/_cds_access_cds_func_in_python_scripts.html However, I have a question how to print the whole Project tree and not just devices? Of course I need to remove check: if treeobj.is_device: But simply removing this test condition will not produce what I want. I need to print PLC Logic, Application, ad other nodes in the Project tree. Where to find this documentation?
Last updated: 2024-08-12

Post by gatto on CAA File open Problems ^{CODESYS Forge talk (Post)}
Ciao, here same question https://forge.codesys.com/forge/talk/Engineering/thread/2538729618/ in this post https://forge.codesys.com/forge/talk/Engineering/thread/4586a90290/?limit=25#d531 i find : keep in mind that all files which are generated / or read should be exist in the iecfilepath this means: for Windows (Control Win as example) c:\ProgramData\CODESYS\CODESYSControlWinV3x64\268E8ADF\PlcLogic for Linux /var/opt/codesys/PlcLogic I never use codesys on windows but im sure on linux we can manipulate file only inside /var/opt/codesys/Plc Logic. Or you need to modify the file codesyscontrol.cfg for change path permission, but this is another history Buone feste !
Last updated: 2024-12-21

Post by timvh on ernesto881124 ^{CODESYS Forge talk (Post)}
You will need a USB to RS485 converter to connect the PC to the Modbus RTU Slave Device. In Windows this converter will be recognized as Serial COM poort (e.g. COM2, or COM3, see the windows device manager to find this out). Select this port in your CODESYS application. On the PC you need to use the CODESYS Control Win (SoftPLC) to run your application. It will not work in simulation mode, because then the Modbus Communication will not be activated.
Last updated: 2023-09-14

Post by taqamert on Codesys 2.3 & Peak PCAN ^{CODESYS Forge talk (Post)}
Despite working on it for days, I haven't achieved any results. I followed the necessary steps one by one as mentioned in the file you sent, but there hasn't been the slightest change. I couldn't find the step you mentioned "Set the 'Can Board Type' to PCAN USB" in the Word document. There is no such setting anywhere I looked. Is there a more detailed explanation available, or can you explain it in more detail? What am I missing?
Last updated: 2024-07-16

Post by trusty-squire on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
What do you mean by continuous movement? You want to continuously follow a dynamic target position? SMC_ControlAxisByPos, which is typically used with CNC Interpolators, could work for that. Instead of feeding the target position in from the Interpolator, feed in the target position from your server instead. Once you enable the FB, it will continuously move the axis to track the fSetPosition input. https://content.helpme-codesys.com/en/libs/SM3_CNC/Current/SM_CNC_POUs/SoftMotion-CNC/Direct-Axis-Control/SMC_ControlAxisByPos.html
Last updated: 2024-09-12

Sort by relevance or date