Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
I have now conducted some tests. The problem occurs when the Python script establishes an OPCUA connection, even if I only establish the connection without reading or writing any data. Is there another way to exchange data between Python and CODESYS without having to put in a lot of effort?
Last updated: 2024-06-24

Post by kaotic2499 on Upgraded Raspberry 2b to Raspberry 5, Trends Broken? ^{CODESYS Forge talk (Post)}
Is there anyone who can assist me? ill just have to raise this as a bug with codesys otherwise. I see this as the only way foward. ill attempt a fresh install of RPI in the next day or two, but thats all i had previously so 🤷‍♂
Last updated: 2025-10-21

Post by alessandro on Configuring a CIP object for Explicit Message ^{CODESYS Forge talk (Post)}
We used this with shared memory codesys. and work. OpENer is an EtherNet/IP™ stack for I/O adapter devices; supports multiple I/O and explicit connections. And we adapt this also for Implicit message. But for arrive to the end we spend a lot of time. :-(((
Last updated: 2025-10-24

Post by vtec35 on search runtime 4.9.0.0 for pi 3 ^{CODESYS Forge talk (Post)}
Hello everyone, following corrupted data on the SD card of our Pi3B+ provided with a machine, we reinstalled a CODESYS image for Raspberry Pi, but we cannot find the 4.9.0.0 runtime that is compatible with the project. Currently, the machine is on 4.1.0.0, and we tried a more recent version 4.13.0.0, but there are error messages. Thanks in advance.
Last updated: 2025-10-24

Post by mg0815 on ERROR: Calling the program "AlarmStorage_Prg" is not allowed from multiple tasks ^{CODESYS Forge talk (Post)}
I use Codesys 3.5.21.1 too I have absolutelly the same fault. Do you know the solution? I get the same massages accept the last one (up to your's from 2025-08-03 04:38) The last messages do not appear. (your's later than 2025-08-03 04:40) Reagards Mg
Last updated: 2025-11-04

Post by kalmeyer on Stepper motor control with (SM_Drive_RaspStepper_direct) ^{CODESYS Forge talk (Post)}
I AM VERY GRATEFUL FOR YOUR HELP. I HAVE INSTALLED: CODESYS SOFTMOTION VER. 4.19.0.0 AS SEEN IN THE ATTACHED FILE. BUT IT DOESN'T CHANGE THE FACT THAT I GET 6 ERRORS WHEN I HAVE INSTALLED SM_Drive_RaspiStepper_Direct DO YOU HAVE ANY SUGGESTIONS ON WHAT I CAN DO NOW? /KLAUS
Last updated: 2025-11-10

Post by ahofer on Deploy Control SL kein Zugriff aus der vertuellen Maschine ^{CODESYS Forge talk (Post)}
Mein Windows mit CoDeSys (V3.5.20.60) läuft in einer virtuellen Maschine. Bis jetzt konnte ich daraus über das Tool "Update Raspberry Pi" auf den Raspberry zugreifen. Mit dem Deploy Control SL geht das jetzt leider nicht mehr. An Wondows wurde eigentlich nichts verändert Weiß jemand Rat? Danke schon mal und VG Toni
Last updated: 2025-12-04

Post by michaelhepiroc on CIA405.RECV_EMCY ^{CODESYS Forge talk (Post)}
Hi Reinier, I'm wondering if you managed to get this FB to work? I was just trying it, and found it not to work, I get an EMCY message in the CodeSys program under the Device Status, but the FB doesn't pick up any EMCY messages from the Bus. Cheers.
Last updated: 2025-12-08

Post by kaotic2499 on Upgraded Raspberry 2b to Raspberry 5, Trends Broken? ^{CODESYS Forge talk (Post)}
There is currently a bug with the Raspberry Pi 64 SL where it is unable to Trend Global Retain or PersistantVars. The work around is to use standard Global Variables for Trend Data. This will be patched by Codesys in the near future reference "VIS-6170"
Last updated: 2025-11-13

Post by gatto on warning C0195 ^{CODESYS Forge talk (Post)}
Good morning dear codesys users. I'm using 3.5.20.40 and I get this warning C0195 when I assign an initial value to xyz. However, if I do it on a single byte (abc), it doesn't display any warning. Why? VAR_GLOBAL abc : BYTE := 100 ; xyz : ARRAY [1..10] OF BYTE := [10(100)] ; END_VAR
Last updated: 2025-11-20

Post by timvh on Textfield display problem ^{CODESYS Forge talk (Post)}
Did you test this with the latest version of the CODESYS Visualization add-on? Something that you might want to test is if it works better when you disable the "Support client animation and overlay of native elements". Double-click on the VisualizationManager in your project to find this setting.
Last updated: 2025-11-21

Post by bertram on Installation IOT Libraries kann nicht installiert werden ^{CODESYS Forge talk (Post)}
IOT Package SL 1.12.0.0 läst sich nicht Installieren da keine Installation gefunden wurde in die die das Package installiert werden kann. Windoof 11 Installer 2.5.0 Codesys V3.5 SP21 Patch 3+ 64 Bit. Hat jemand einen Rat für mich ? Bin um jeden Tip dankbar. herzliche Grüße an alle.
Last updated: 2025-11-25

Post by blitz on SMC_ERROR SMC_CGR_INVALID_POSPERIOD ^{CODESYS Forge talk (Post)}
Codesys - SMC_ERROR SMC_CGR_INVALID_POSPERIOD - Invalid modulo period less than or equal to zero or greater than half the bus bandwidth. Has anyone seen this error and actually understands what it means and how to get rid of it? I tried to work around it by reducing the number of increments on the drive but then the drive itself starts throwing errors.
Last updated: 2025-12-15

Post by worker69 on Alarmgruppenvorlage kann über Kontextmenü keine weitere Latch Variable hinzugefügt werden ^{CODESYS Forge talk (Post)}
Hallo, ich habe das problem, dass ich in einer Alarmgruppenvorlage keine wietere LATCh Variable hinzufügen kann. Wenn ich dies über das Kontextmenü versuche, dann erscheint folgende Fehlermeldung "Der Objektverweis wurde nicht auf eine Objektinstanz festgelegt". Ich verwende Codesys V3.5.19 P0 und 23.5.19 P7 Was mache ich falsch
Last updated: 2026-01-05

Post by bdschnapp on OPC-UA ApplicationUri / ProductUri ^{CODESYS Forge talk (Post)}
From Codesys support: The format of the URN is always the same. It's always urn:<vendor>:<product>:OPCUA:Server. What I think you can influence the vendor and product (DeviceName) through settings in the runtime cfg file:</product></vendor> [SysTarget] VendorNameUnicode="T\00E\00S\00T\00" DeviceNameUnicode="t\00e\00s\00t\00" Note that these are 16-bit strings, thus the ASCII padded with nulls
Last updated: 10 hours ago

Post by elektron785 on Nach Neuinstallation Plug-In Fehler ^{CODESYS Forge talk (Post)}
Ich kann nur sagen, dass ich die gleichen Probleme habe. Aber auch erst neuerdings. Zuerst kam auch die Meldung mit dem falschen Versionsprofil. Habe jetzt schon mehrere Sachen versucht Neuinstallation / Reparatur. Alles deinstalliert. Leider hat das bei mir noch nicht geholfen. Codesys läuft unendlich langsam - immer wieder keine Rückmeldung.
Last updated: 2026-01-22

Post by peteryapab on Login Screen to small for 10" screens ^{CODESYS Forge talk (Post)}
Hi! I hade made a visualization within Codesys V3.5 SP21 Patch 3, where i call for the user management and login. The VisuUserManagement.VMU_Login and VisuUserManagement.VMU_Login2 are to small for the screen it looks good and works fine if you are on a computer with large scrren but gets finicky on the smaller screen. any ide´s how to make the login dialog bigger?
Last updated: 2026-02-01

Post by timvh on CODESYS: Combining Master Redundancy with EtherCAT Ring Topology – Is it Supported? ^{CODESYS Forge talk (Post)}
Yes, this works (at least we have it running with Wago PLC and Beckhoff I/O), but the concept works. You need 2 PLC's with at leat 3 network interfaces. And 2 switches (can be unmanaged). See the attached simple diagram for the solution.
Last updated: 2026-02-05

Post by mrkm-dic on CODESYS: Combining Master Redundancy with EtherCAT Ring Topology – Is it Supported? ^{CODESYS Forge talk (Post)}
Hi! thanks for reply. We tested the configuration you proposed as well; however, when the cable between the controller and the switch was disconnected, the Active and Standby roles were swapped. Did you observe the same behavior in your configuration using WAGO and Beckhoff?
Last updated: 2026-02-06

Post by gatto on EXCEPTION [watchdog] how to find position cause ^{CODESYS Forge talk (Post)}
hi. My plc is weidmuller UC20-WL200-AC, IDE CODESYS 3.5.20.40, see picture for task settings. sometime i've got the plc stop. Reading the log, I find: EXCEPTIONPOSITION : IP=0x(nil) (no IECcontext could be retrieved) component CmpIecTask EXCEPTION [Watchdog] occurred: App=[Application], Task=[TASK_O_MAIN] component CmpIecTask How to find the position of problem?
Last updated: 2026-02-06

Post by yr00 on OPC UA datasource low read frequency ^{CODESYS Forge talk (Post)}
Hello everyone, I am trying to test the OPC UA client feature in Codesys. My setup is the following; I have a Codesys simulation/ visualization running on Control Win V3. My OPC UA server is hosted on a Siemens 1518 PLC using PLCSim Advanced. The setup is completely virtual so there are no really PLCs. Everything is on my laptop. Writing data from the Codesys simualtion to the server is very quick. I have a PLC program running on another 1500 PLC which reads data from simulation via the server, and changes in the simulation (e.g. button pressed) appear within hundreds of miliseconds if not tens of miliseconds in my PLC program. However, when it comes to reading data from the OPC UA Server by Codesys, it taks around 1-2s. I connected a UAExpert client and it gets update very quickly so I am fairly sure the problem is with Codesys. I have tried changing the update rate in datasource -> General and Diagnosis, but it doesn't seem to have an effect. Do you guys have any suggestion on what I can do?
Last updated: 2023-08-29

Post by ofey on Codesys Soft PLC OPC UA server ^{CODESYS Forge talk (Post)}
Hi! I'm sorry if this has been asked before. I have tried looking up previous topics regaring this, but even though I'm following tutorials and other posts I cant seem to get this to work consistently. I actually got the connection established on a test project after some trial and error. I only got it to work with the "Anonymous login". But after i deleted the test project and tried to get the same thing to work on another project I cant get it to work anymore. What I'm trying to do: Set up and OPC UA Server using CODESYS with the free soft PLC. I then try to connect to the OPC UA Server with the program "UaExpert". What happens: I get the error Error "'BadUserAccessDenied' was returned during ActivateSession". What I have done in CODESYS: - Added the object "Symbol configuration" and checked some test variables - Checked "Support OPC UA features - In "Communication settings -> device -> Change runtime security policy" I have checked "Allow anonymous login" What I have done in UAExpert: - Found the OPC UA server under "local". (It is showing two servers though, I do not know why. It showed the same when it worked yesterday). Se attachment - Checked "Anonymous" under "Authentication settings in the OPC UA server. I'm new to CODESYS, so it could be something elementary wrong in my settings. Maybe something in the user settings in CODESYS regarding user rights or something?
Last updated: 2023-09-14

Post by cihangur on OpC UA server on Raspberry Pi 64 SL runtime ^{CODESYS Forge talk (Post)}
Hello everyone, I wanted to write here because it is a similar and the most up-to-date topic. I want to connect to CoDeSys Win V3 x64 - 3.5.19.50 with OPC UA using WinCC Advanced V17. (Or to a PLC with CoDeSys Version 4.10.0.0) My settings are exactly the same as the previous comment. I even tried many different settings. I can access all CoDeSys OPC UA variables via TIA Portal IDE and add them to my HMI tags. When WinCC RT Advanced is started, it gives a warning that the connection could not be established and does not update the variables. I can connect to Inovance AM600 using CoDeSys Target version 3.5.11.50. (The same version Win x64 is also connected.) However, a security setting in the current versions prevents me. I would be very happy if those who have up-to-date experience on this issue and find a solution share it. The CoDeSys Security Settings which I can access variables with TIA Portal: CommunicationPolicy: POLICY_BASICSHA256SHA256 CommunicationMode: ALL Activation: Activated UserAuthentication: ENABLED Server Certificate: Valid until 2034 Greetings.
Last updated: 2024-12-06

Post by gunstr on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
We have been using the Codesys Control for Rasberry Pi for several years in many installations without any major issues. But during summer the problem mentioned above has blocked further deliveries. We have made some minor upgrades to the application but I do not really see why that should have any impact. HW is Raspberry Pi 4B, 2GB OS is Booworm Lite Codesys control is version 4.15 (have just installed a few systems lately with this version) The system boots OK but after exactly 30 seconds Codesys is shut down and becomes unreachable. We have tested several different combinations: Upgrade of the Codeys Control to 4.16 Loading different Codesys applications Changing to 4GB version of the Raspberry Pi One of the test applications together with the 4GB HW seems to be stable, but all other combinations fails. Any suggestion what we can do to resolve is appreciated - this is a real business blocker now. Rgds
Last updated: 2025-09-02

Post by ranadheer on Codesys Control for PLCnext (PLC - AXL F 2152) ^{CODESYS Forge talk (Post)}
Hello Jaco Pretorius, I came across your post regarding CodeSys control for PLCnext. I’m currently working on a similar setup and had a quick question. Here am using the CODESYS V3.5 SP21 PATCH2 ,VERSION 3.5.21.20 , and Downloaded extension package 4.16.0.0 (old versions are not available in the extension CodeSys installer) Devices used here are: BUS COUPLER : 2403869 BK PN TPS Module carrier slot 1 : 1088127 AXL SE DI16/1 Module carrier slot 2 : 1088062 AXL SE AI4 | 4-20 Module carrier slot 3 : 1088129 AXL SE DO16/1 Module carrier slot 4 : 1088123 AXL SE AO4 | 4-20 -->Start a New Project Type: Standard Project Device: CODESYS Control Win V3 x64 Language: Structured Text -->Install GSDML File Navigate to: Tools > Device Repository > Install Select the GSDML file path (downloaded from Phoenix Contact for device coupler Part ID: BK PN TPS 2403869) Click Renew Device Repository Close the dialog -->Add Device to Project -->Right-click on Devices > Add Device Issue: Devices from the repository are not available to select or call into the project! I’d really appreciate any guidance or suggestions you can offer. Best Regards Ranadheer Reddy
Last updated: 2025-09-09

Sort by relevance or date